Theben RAMSES 812 BLE User manual

1
RAMSES 812 BLE
8120150
307400
Clock thermostat
EN
1. Basic safety information
Danger of death through electric shock or fire!
 Installation should only be carried out by a
qualied electrician!
WARNING
•The clock thermostat conforms with EN 60730-2-9 if
correctly installed
•Corresponds to type 1 B in accordance with IEC/EN
60730-2
•Operation and programming only via RAMSES BLE app
•With external input (no SELV, adjustable)
2. Proper use
•Heating control for time-dependent monitoring and
control of room temperature in single-family houses,
ofces etc.
•Use in dry rooms with normal levels of domestic
cleanliness
Disposal
Dispose of device in environmentally sound manner
3. Installation
Mounting the clock thermostat
Electrostatic discharge!
Caution, sensitive electronic components!
When tting, observe ESD safety measures (elect-
rostatic discharge).
!Position the clock thermostat on an internal wall, at
about eye level.
!Avoid drafts or heat emission.
LFor wall mounting



Attach the mounting plate above the wall outlet for the
supply line .
Engage and wire the circuit board carrier .
First, hook in the upper part of the clock thermostat on top,
then engage .
Put on the cover .
Dismounting the clock thermostat
Using a screwdriver, loosen the front panel at the two side
and bottom openings .
Then release the catches on the left and right and remove
the upper part of the housing .
Loosen the plug-in connectors and press the circuit board
carrier together at the top and bottom .
Remove the circuit board carrier through the front.
4. Connection
Power is supplied via L and N (see technical data); the con-
nection to the boiler is made via a relay contact.
!Disconnect the boiler from mains supply before connec-
ting the thermostat.
!In order to eliminate the possibility of EMC interference,
always lay the mains supply feed separate from the
external input (if one is being used).
!Faulty connections will damage the device.

2
N
L
4
3
1
2
56
230 V (N)
230 V (L)
ext
*
**
*external sensor 9070321/9070459
** floating contact
ext
Relay
Relay
Relay
Relay
*external sensor 9070321/9070459
** fl oating contact
Terminal layout
1 Relay
2 Relay
3 230 V~
4 230 V~
5 ext. input
6 ext. input
5. Manual setting at the clock thermostat
Button with LED display for setting
– Comfort mode (green LED on)
– ECO mode (green LED off)
With the button, you can select either comfort mode or ECO
mode.
1. Quick selection of comfort or eco mode
Press the button
▻ Comfort mode or eco mode will be set.
At the next switching time, the quick selection will be reset.
2. Pairing
Press the button for 3 s
▻RAMSES BLE can be connected with a smartphone/
tablet (paired) for 5 min. (green LED fl ashes). If pairing
is successful, the LED goes out.
Delete pairing
Press the button for 6 s
▻All connections saved in the RAMSES BLE (pairing) will
be deleted (red LED fl ashes)
Delete the connection/pairing also on the smartphone/
tablet (Settings →Bluetooth pairing →delete respective
device (RAMSES BLE)).
The PIN will be reset to 0.
3. Reset
Press the button for 12 s
▻Hardware reset (the red LED goes out)
6. Settings and functions – operation via
Theben app
Is my smartphone BLE capable?
Download Bluescan app for Android and iOS
The app can be used to check whether a device is BLE capa-
ble or not.
RAMSES BLE app
Set temperature, adjustable in
increments of 0.2 °C (2 °C
– 30 °C)
Selection RAMSES BLE
Settings, device management
Software info
Info: External input, relay, PIN etc.
Programming of
switching times
Operating modes:
– Programs P1 – P3
– Comfort, reduction, frost
Quick selection
Comfort mode*
Quick selection
Eco mode*
*until the next switching time

3
Connecting clock thermostat and smartphone (via
app) – pairing
The clock thermostats can be programmed using an app
(from Android 4.3, iOS 5) on a mobile end device. Communica-
tion takes place via Bluetooth BLE.
Download the RAMSES BLE app from the App Store or
Google Play Store
Open the app
▻ Window with offl ine mode/assign appears
Press the button on RAMSES BLE for 3 s (green LED at
RAMSES BLE fl ashes)
Press Assign
▻Device list appears
Select device and press ok
Enter the name for RAMSES BLE (e.g. living room …)
Con rm with ok
▻ RAMSES BLE is now paired. Each time when restarting
the app, a connection will be established. This takes
several seconds (the Bluetooth icon on the top left of
the app fl ashes)
Loading additional devices ...
Press device management
▻A window will open
Press +
▻ Further devices will be searched ...
Program
In the program menu,
•programs P1 – P3 can be changed
•a new program, or
•a holiday program can be created, or
•Programs P1–P3 can be set, edited, or deleted.
•A maximum of 24 switching times can be set per pro-
gram, up to a total of 42.
LDuring programming, selected days are shown like , and
unselected days like .
The created programs are automatically sent to the clock
thermostat.
Creating a holiday program
In order to create a holiday program and activate it,
slide the controller to "Activation"
After a holiday program has been created via the app, the
clock thermostat receives the following information:
– active/not active
– Start date and end date with time
– Room set temperature during holiday time

4
Info
Settings
Press Settings
▻A window will open
A window will open
LThe functions in this submenu have to be set by the quali-
 ed electrician.
In the settings, language, temperature (comfort, eco, frost),
wall compensation, optimisation, etc. can be set.
1. Setting the wall compensation
If the installation location is unfavourable, temperature
deviations between detected and actual room temperature
might occur. This difference can be corrected by using the wall
compensation.
2. Setting the controller
Behaviour of a PD controller (pulse duration controller)
With adapted heating systems, a PD controller is characte-
rised by its short transient time, minimal overshoot and high
control accuracy.
– Control period: 5 bis 30 min
– Control range: ± 0,2 K bis ± 5 K
Behaviour of a hysteresis (on/off) controller
In over or undersized heating systems, a hysteresis controller
is characterised by a minimum switching frequency and low
temperature deviations.
– Switching hysteresis: ± 0,2 K bis ± 1 K
3. External input
The external input can be con gured for various external
sensors.
!Input is active, therefore do not use external voltage.
The connected contact must be fl oating and electrically
isolated.
The following options are available with the individual sen-
sors/contacts
Floor Temperature
limit
Floor temperature restriction, fl oor
temperature selection adjustable
between 20 °C and 50 °C; fl oor sensor
(9070321)
Lno safety temperature limiter, but
device type 1 B in accordance with
EN 60730-1
Room
temperature
no options The internal temperature sensor will
be switched off; external temperature
sensor (IP 65) (9070459)
Presence
detector
Temperature
selection
This temperature is used for control
if the HVAC output of the presence
detector is switched. If no presence is
detected, the set program is used for
control
Window contact no options As long as the window contact is swit-
ched, the thermostat controls to frost
protection temperature
Telephone
contact
Temperature
selection
Select temperature for the controller if
the telephone contact is switched

5
Error display at RAMSES BLE
LIf the external input is set to "fl oor" or "room temperature", an
appropriate temperature sensor has to be connected. If this sen-
sor is missing, the red LED fl ashes at one second intervals.
4. Setting the optimisation
The optimisation function allows you to achieve a certain
room temperature at a desired switching point. The display
shows how many minutes earlier the heating starts. This time
applies per K of temperature difference between actual tem-
perature and desired set temperature.
Example
At 06.00 a.m. in the morning, a change in the bathroom is
programmed from reduction (17 °C) to comfort temperature
(23 °C).
Without optimisation function, the room thermostat enables
the heating request for the bathroom at 06.00 a.m. Depen-
ding on the size of the room and the installed heating system,
the bathroom reaches the desired 23 °C at 6.30 a.m., for
example.
With a set optimisation of 5 min/K, the thermostat sends the
heating request earlier, as follows:
Set temperature at 06.00 a.m.  23 °C
Actual temperature  17 °C
i.e. Delta T = 6 K
6 K * 5 min/K = 30 min
The controller sends the heating start 30 min. earlier and
reaches the setpoint temperature at 06.00 a.m.
LThe optimisation value depends on the spatial and heating
conditions.
5. PIN
This function can be used to assign a new PIN.
•The factory setting for the PIN is 0.
•New PIN can be entered (1–6 digits).
•In case of Delete pairing (2nd pairing), the PIN is set to
0.
•If the PIN is 0, the PIN will not be requested during
pairing.
7. Technical data
Supply voltage: 230 V AC +10 %/–15 %, 50 Hz
Controller type: Hysteresis controller or pulse
duration controller
Contact: Swich contact µ max. 8 (1)
A/250 V AC
Temperature setting range: + 2 °C ... + 30 °C in increments
of 0.2 °C
Memory locations: 42
Protection rating: IP 20 in accordance with EN
60529
Protection class: II in accordance with EN
60730-1
Operating temperature: + 0 °C ... + 50 °C
Power reserve: 4 hours
Mode of operation: Type 1 B in accordance with EN
60730-1
Rated impulse voltage: 4 kV
Pollution degree: 2
Software Class A
Theben AG herewith declares that this type of radio installation
complies with Directive 2014/53/EU. The complete text of the
EU Declaration of Conformity is available at the following Internet
address: www.theben.de/red-konformitaet
8. Contact
Theben AG
Hohenbergstr. 32
72401 Haigerloch
GERMANY
Phone [phone]
Fax [phone]
Hotline
Phone [phone]
[email protected]
Addresses, telephone numbers etc.
www.theben.de