Theben SYN 161 h User manual

310 281 06
t
Operating instructions
SYN 161 h
SUL 181 h
MOUNTING INSTRUCTIONS
Safety information: Electrical devices should only be connected
and mounted by an electrical specialist. Manipulations and modi-
fications on the switch will result in loss of warranty. The national
specifications and applicable safety regulations must be obser-
ved.
Synchron
230 V / 50 Hz
Quartz * R = 3d (72h) LiMh
230 V / 45 – 60 Hz
16 A
250 ˜
*The quartz movement starts automatically after
a few minutes by an applied voltage. The full
power reserve is built up after about 3 days.
24 h Programm

310 281 06
t
Operating instructions
SYN 161 h
SUL 181 h
MOUNTING INSTRUCTIONS
Safety information: Electrical devices should only be connected
and mounted by an electrical specialist. Manipulations and modi-
fications on the switch will result in loss of warranty. The national
specifications and applicable safety regulations must be obser-
ved.
Synchron
230 V / 50 Hz
Quartz * R = 3d (72h) LiMh
230 V / 45 – 60 Hz
16 A
250 ˜
*The quartz movement starts automatically after
a few minutes by an applied voltage. The full
power reserve is built up after about 3 days.
24 h Programm

310 281 06
t
Operating instructions
SYN 161 h
SUL 181 h
MOUNTING INSTRUCTIONS
Safety information: Electrical devices should only be connected
and mounted by an electrical specialist. Manipulations and modi-
fications on the switch will result in loss of warranty. The national
specifications and applicable safety regulations must be obser-
ved.
Synchron
230 V / 50 Hz
Quartz * R = 3d (72h) LiMh
230 V / 45 – 60 Hz
16 A
250 ˜
*The quartz movement starts automatically after
a few minutes by an applied voltage. The full
power reserve is built up after about 3 days.
24 h Programm

310 281 06
t
Operating instructions
SYN 161 h
SUL 181 h
MOUNTING INSTRUCTIONS
Safety information: Electrical devices should only be connected
and mounted by an electrical specialist. Manipulations and modi-
fications on the switch will result in loss of warranty. The national
specifications and applicable safety regulations must be obser-
ved.
Synchron
230 V / 50 Hz
Quartz * R = 3d (72h) LiMh
230 V / 45 – 60 Hz
16 A
250 ˜
*The quartz movement starts automatically after
a few minutes by an applied voltage. The full
power reserve is built up after about 3 days.
24 h Programm

manual
i
Manual Control ON/OFF (Override Control)
Turn the control axis ❶ in direction of arrow by one notch; ON=
+ or OFF = -. The manual control is automatically
annuled by the following counteracting command of the automatic
program sequence.
permanent ON / OFF
i
Permanent Control ON/OFF
Set the hand lever ❷to »perm« = permanent control; turning the
control axis ❶in direction of arrow, the required permanent con-
trol ON or OFF can now be adjusted. Turning the hand lever to
»Auto« = Automatic Control, the permanent control is terminated.
The actual switch position is maintained until the next counterac-
ting command of the automatic program sequence is triggered.An
immediate correction can be carried out by means of the manual
control (override control).
EMV / CEM / EMC / ETY
The time switches are in accordance with the European direc-
tives 73/23/EEC. (Low-Voltage Directive) and 89/336/EEC (EMC-
Directive). If the time switches are used together with other devi-
ces in an installation, take care that the complete installation
does not cause a radio interference.
Service
쮕Theben AG
Postfach 56, D-72394 Haigerloch
Telefon [phone], Telefax: (0 74 74) 692 150
Kundendienst
Telefon [phone], Telefax (0 74 74) 692-207 www.theben.de
ENGLISH
 TIMEGUARD LTD,
Victory Park, 400 Edgware Road
London NW2 6ND
Tel. [phone];
Fax: [phone]
 PETER WARBURTON PTY. LIMITED,
64 Brittania Road, Castle Hill
NSW 2154, Australia,
Tel.: [phone],
Fax: [phone]
AUS

manual
i
Manual Control ON/OFF (Override Control)
Turn the control axis ❶ in direction of arrow by one notch; ON=
+ or OFF = -. The manual control is automatically
annuled by the following counteracting command of the automatic
program sequence.
permanent ON / OFF
i
Permanent Control ON/OFF
Set the hand lever ❷to »perm« = permanent control; turning the
control axis ❶in direction of arrow, the required permanent con-
trol ON or OFF can now be adjusted. Turning the hand lever to
»Auto« = Automatic Control, the permanent control is terminated.
The actual switch position is maintained until the next counterac-
ting command of the automatic program sequence is triggered.An
immediate correction can be carried out by means of the manual
control (override control).
EMV / CEM / EMC / ETY
The time switches are in accordance with the European direc-
tives 73/23/EEC. (Low-Voltage Directive) and 89/336/EEC (EMC-
Directive). If the time switches are used together with other devi-
ces in an installation, take care that the complete installation
does not cause a radio interference.
Service
쮕Theben AG
Postfach 56, D-72394 Haigerloch
Telefon [phone], Telefax: (0 74 74) 692 150
Kundendienst
Telefon [phone], Telefax (0 74 74) 692-207 www.theben.de
ENGLISH
 TIMEGUARD LTD,
Victory Park, 400 Edgware Road
London NW2 6ND
Tel. [phone];
Fax: [phone]
 PETER WARBURTON PTY. LIMITED,
64 Brittania Road, Castle Hill
NSW 2154, Australia,
Tel.: [phone],
Fax: [phone]
AUS