Thermo Scientific mySPIN 6 User manual

Instruction Manual ..................................................2
Manuel d’instructions............................................12
Manual de Instrucciones .......................................22
Bedienungsanleitung.............................................32
Manuale d'uso......................................................42
Instruction Manual
50145670-b • 09 / 2016
Thermo Scientific
mySPIN 6 Microcentrifuge

Safety Precautions
The Thermo Scientific™ mySPIN 6 Microcentrifuge is a personal mini-centrifuge designed for
laboratories in the bioscience, medical, and chemistry fields. It may be used with biohazardous
and/or hazardous materials. This instruction manual cannot address all safety hazards. It is
the responsibility of the user to consult and observe all health and safety precautions and to
assess the instrument’s suitability to the task.
CAUTION
Before starting the centrifuge for the first time, please read this instruction manual carefully.
This manual contains important information, safeguards, and operating instructions.
1. Never use this product in any manner inconsistent with these instructions.
2. This product is intended to be used indoors only.
3. This product is intended for separating aqueous solutions in approved test tubes
compatible to the RCF of this unit.
4. This product is not intended to centrifuge very dense materials. Do not use materials
with a density greater than 1.2g/cm³.
5. Use only the power adapter delivered with the product. Use of other power adapters will
void warranty.
6. Do not put hands in the rotor area unless the rotor is completely stopped.
7. Only use the originally supplied rotors, AC adapters, tube adapters and any other
spare parts delivered with the unit. These parts have been designed to safely meet
the maximum RCF that the centrifuge is able to deliver. DO NOT USE ROTORS OR
COMPONENTS FROM ANY OTHER MANUFACTURER.
8. Always make sure the rotors are securely seated.
9. Never use this product in any manner inconsistent with these instructions.
10. Observe general laboratory safety precautions and regulations.
11. Do not attempt to operate with the cover removed or open.
12. The rotor and lid must always be securely fastened when in operation.
13. Do not use damaged rotors.
14. Do not move unit while the rotor is spinning.
15. Do not attempt to stop the rotor while the unit is running. Doing so may cause injury or
the unit to fail and will void the warranty.
16. Do not immerse unit in water. Injury due to shock or fire may result.
17. The rotor must be loaded symmetrically. Operating this unit with an unbalanced rotor will
cause severe vibration and damage, which is not covered by warranty.
18. Do not fill tubes while inserted in rotor. Spilled liquid may harm unit.
2

3
19. Close tube lids before starting centrifuge. Open lids can be ripped off during centrifugation
and damage the unit. Open lids can cause fluid to be dispersed inside the centrifuge.
20. Do not insert non-standard tubes or other unfamiliar articles into the rotor.
21. Follow all precautions from the Material Safety Data Sheet (MSDS) for any reagent you
use with this instrument.
22. Do not use solvent or flammable liquids near this or other electrical equipment.
23. Do not centrifuge materials that in combination or alone are flammable, explosive, or
corrosive, or may cause any other hazard.
24. Do not operate in a hazardous or flammable environment.
25. Do not use any solvent on the unit that may attack plastic or rubber or cause cracks in
the rotor.
26. Ensure the rotor is protected from corrosion and mechanical damage. The rotor must be
cleaned with a pH-neutral cleaning liquid.
27. Before using any cleaning or decontamination methods except those recommended in
this manual, contact Thermo Fisher Scientific to ensure that the proposed method will
not damage the device.
28. If a single level of hazard protection is required, make sure to use containers that are
tested to Risk Group II or above and that more than one level of protection is provided in
the case of materials of a higher Risk Group.
29. Should the unit fail to work to specification, immediately stop centrifuging and allow the
rotor to come to a complete stop. Clean and troubleshoot the product according to the
instructions under “Trouble Shooting” before any further use of the product. Contact an
authorized dealer or the manufacturer if trouble persists.
30. Always work in a manner which endangers neither the user nor any other person.
31. Repairs are to be performed by trained and authorized service personnel only. Contact
Thermo Fisher Scientific.
32. Opening the instrument housing or improper use of the instrument voids the warranty. If
there is a failure during the warranty period, contact Thermo Fisher Scientific for warranty
service.
33. Do not use units that have not been correctly installed or repaired.
34. Do not attempt to disassemble or modify this product.
35. Store at room temperature in a dry area. Do not expose to sunlight, moisture, or extreme
temperatures for prolonged periods of time.

4
WARNING
The laboratory procedure should ensure that no person or hazardous substances are present
within a 12” (30 cm) zone around the centrifuge when operating.
WARNING
If this product is not used as recommended by the manufacturer, the overall safety will be
impaired.
WARNING
Check MSDS, wear required Personal Protective Equipment, and observe all applicable local
and national regulations before dispensing and disposing of hazardous materials.
WARNING
This product does not contain bio-seals as per IEC/EN/CSA 61010-2-020 and cannot provide
any level of containment in case of a spill or release of toxic, radioactive, or pathogenic micro-
organisms. Thus these materials are not recommended to be used with this product.

5
This mark is the confirmation that the unit conforms to the EU guidelines
and has been tested according to the following EU Declaration of Conformity.
Specifications
Environmental Ratings
Note: for Indoor use
Altitude: up to 2000 m
Temperature: 2 °C to 40 °C
Maximum Relative Humidity: 80% for temperatures up to 31 °C decreasing linearly to 50%
relative humidity at 40 °C
Technical Features
Dimensions: 153 mm x 128 mm x104 mm (LxWxH)
Weight: 1.6 lb (0.73 kg) (with rotor)
1.9 lb (0.86 kg) (with power adapter)
Maximum speed: 6,000 rpm Approx.(with fully loaded rotor)
Maximum RCF: 2,000 x g
Electrical
Power Adapter rating
Input: 100-240 V AC
50/60 Hz, 0.8 A
Output: 12 V DC
mySPIN 6
Input: 12 V DC
Current (under load): Approx. 0.6 A
Power: Approx. 7.3 W
Accessories:
• Six tube adapters for 0.2 mL tubes and six tube adapters for 0.5 mL tubes; PN: 50146145
• One SnapSpin™ strip tube rotor (can be used in place of installed round rotor); PN:
75004063
Conforms to:
ANSI/UL Std. 61010-1
IEC/EN 61010-1
IEC/EN 61010-2-020
CAN/CSA C22.2 No. 61010-1.
NOTE
All accessories are rated for maximum speed.
This product has been tested to the requirements of CAN/CSA C22.2 No.
61010-1 second edition, including Amendment 1, or a later version of the
same standard incorporating the same level of testing requirements.

6
EC Declaration of Conformity
Model: Sprout
Manufacturer: Heathrow Scientific®
Address: 620 Lakeview Parkway, Vernon Hills, IL 60061 USA
European Contact: Emergo Europe
Molenstraat 15, 2513 BH, The Hague,
The Netherlands
This unit has been constructed and conforms to the following:
Safety Standards:
IEC/EN 61010-1
IEC/EN 61010-2-020
UL Std. 61010A-1, 61010A-02-20
CAN/CSA C22.2 No. 61010-1
EMC Standards:
IEC 61326
2012/19/EU (WEEE)
2012/65/EU (RoHS2)
Signed:
Jamie Devin, Managing Director
Disposal Responsibilities:
The equipment you purchased may contain hazardous substances that could impact
the environment. Per regulations on electronic devices in the European Community, you
must use the appropriate disposal systems to avoid exposure of these substances to the
environment. The disposal systems will reuse or recycle hazardous materials from your
equipment responsibly.
The crossed-out wheeled bin symbol invites you to use those systems.
If you need more information on the collection, reuse and recycling systems,
please contact your local or regional waste administration. You can also contact us for more
information on the environmental performance of our products.

Operation
1. Remove the contents from the package, examining them carefully for breakage, defects,
or missing parts. Save the packaging.
2. Place the mySPIN 6 on a sturdy, level surface away from the edge of the counter and
other moving equipment. Make sure the power cord is clear of hot surfaces and other
hazards.
WARNING
Spin balanced loads only!
Do not place the tubes asymmetrically nor load unequal volume tubes. Improper placement of
tubes will lead to insufficient centrifugation and may cause injury or accident.
3. Verify that the power switch is in the OFF position. Plug the power adapter cord into the
rear of the unit and the power cord into an approved outlet.
4. Turn power switch ON. If there is a smooth whirring sound and the unit accelerates
with little or no vibration, mySPIN 6 is ready to use. If there are loud or unusual sounds,
or excessive vibration, DO NOT OPERATE. Contact Thermo Fisher Scientific Technical
Support.
5. On benchtop prepare samples tubes in rack so that tubes are filled to equal levels. Close
tube lids.
6. To open lid, firmly tilt lid toward rear of unit.
WARNING
The laboratory procedure should ensure that no person or hazardous substances are present
within a 12” (30 cm) zone around the centrifuge when operating.
7. Tubes of equal weight and size should be placed opposite each other. Use sample or
water in tube to provide balance. Proper sample balancing illustrated below.
8. Do not force tubes into the rotor. Use adapters and correctly sized rotors for your
application.
2 Tubes 3 Tubes 4 Tubes 6 Tubes
SnapSpin Circular Rotor
7

8
WARNING
Do not open lid until rotor has completely stopped! Avoid severe personal injury or property
damage from moving parts.
WARNING
Do not use damaged or cracked rotors!
Rotor Replacement
To remove SnapSpin™rotor: Press
center button firmly and at the same
time lift rotor
upwards.
To install SnapSpin™rotor: Set
rotor onto the hex shaft.
Press center button firmly and
downward. Rotor should latch
with a click sound.
SnapSpin Strip Tube
9. Close lid securely. A properly closed lid will grasp the front silicon tab keeping the lid
closed. If a clicking sound is heard while the unit is operating, the lid is not fully closed.
Do not attempt to operate with the lid removed or open. Turn power switch ON. Unit will
not operate with lid open. If there is a smooth whirring sound and the unit accelerates
with little or no vibration, mySPIN 6 is ready to use. If there are loud or unusual sounds,
or excessive vibration, DO NOT OPERATE. Contact the Thermo Fisher Scientific Technical
Support.
10. To stop centrifugation, press power switch and wait until the rotor has completely stopped
rotating before opening the lid.

NOTICE
Ensure all parts are throughly dry prior to operation.
Trouble Shooting
Trouble Possible Cause Solution
Not working
No light
• Cord Loose
• Front ON/OFF switch
• Lid not closed
• Check Cord
• Press front ON/OFF switch
• Close Lid
Excessive
vibration
• Rotor not installed correctly
• Rotor not balanced correctly
• Reinstall rotor
• Check for tubes of equal
weight and location (see
Operation)
Noise clicking
sound
• Lid not fully closed • Close Lid engaging silicon tab
with cover
Rotor falls off • Rotor not attached • Reattach rotor (See Rotor
Replacement)
Maintenance
mySPIN 6 is normally maintenance-free. Clean unit only when it is not plugged into an electrical
outlet. When necessary, the housing and rotor can be wiped using a damp cloth and a mild,
non-corrosive detergent.
WARNING
Do not use any solvent on the unit that may attack plastic or cause cracks in the rotor. Ensure
the rotor is protected from corrosion and mechanical damage. The rotor must be cleaned with
a neutral cleaning liquid.
9

thermoscientific.com/centrifuge
© 2016 Thermo Fisher Scientific Inc. All rights reserved.
Heathrow Scientific is a registered trademark of Heathrow Scientific. All other trademarks are the property of Thermo Fisher
Scientific Inc. and its subsidiaries.
Specifications, terms and pricing are subject to change. Not all products are available in all countries. Please consult your
local sales representative for details.
Shown pictures within the manual are examples and may differ considering the set parameters and language.
United States/Canada [phone]
Austria [phone]
Belgium [phone]
France [phone]
Germany national toll free 0800 1 536 376
Germany international [phone]
Italy [phone]
Netherlands [phone]
Nordic/Baltic States/CIS [phone]
Russia [phone]
Spain/Portugal [phone]
Switzerland [phone]
UK/Ireland [phone]
India [phone]
China [phone] or [phone]
Japan [phone]
Other Asian Countries [phone]
Australia [phone]
New Zealand [phone]
Countries not listed [phone]
Thermo Electron LED GmbH
Zweigniederlassung Osterode
Am Kalkberg, 37520 Osterode
Germany