Thermo Scientific Pierce G2 User manual

Select the appropriate program to run:
a. Low MW (< 25kDa)
b. Mixed Range MW (25-150kDa)
c. High MW( >150kDa)
d. Std Semi-Dry
e. 1.5mm thick gels or if unknown
Note: For fast-blotting programs (a, b, c and e), use Pierce
1-Step Transfer Buffer. Transfer time may be increased to
12 minutes for extremely high molecular-weight proteins. Do not
use the Std Semi-Dry transfer program (d) with Pierce 1-Step
Transfer Buffer.
Select the Start button to begin transfer.
Pierce 1-Step Transfer Buffer is a highly concentrated salt solution.
Thoroughly wash the anode and cathode after each use and rinse
the unassembled cassette under hot water while removing any
sticky salt residue with a gloved hand. Rinse with deionized water
and stand parts in a rack to dry. For more thorough cleaning, im-
merse the cassette top (cathode) and bottom (anode) in hot water
and use a gloved hand or clean sponge to remove salt residue.
Rinse with deionized water and stand parts in a rack to dry.
NOTE: Failure to keep cassette top and bottom clean can
result in moving parts sticking and lead to poor transfer
efficiency.
After running at high current, the anode and cathode plates
can become hot. Use caution when separating the gels and
stacks from the plates.
IMPORTANT Review and implement guidelines for proper set-up
before installation. Gels simultaneously transferred must have the
same formulation.
Using the appropriate power cord supplied with the blotter,
connect the blotter control unit to an outlet.
Switch on the Power Button located on the control unit’s rear panel.
For each gel, use four sheets of ~0.83mm thick Western blotting
filter paper and one sheet of nitrocellulose or PVDF membrane cut
to the same size.
Equilibrate filter paper and membrane in Thermo Scientific™Pierce™
1-Step Transfer Buffer for at least 5 minutes. Use sufficient buffer
to cover filter paper and membrane [~50mL per mini-sized (7cm
x 8.4cm) sandwich and ~100mL per midi-sized (8cm x 13.5cm)
sandwich].
Note: PVDF membrane must be wetted with methanol or
ethanol before equilibration in Pierce 1-Step Transfer Buffer.
After electrophoresis, remove gel(s) from cassette(s) and briefly
place into tray containing deionized water or transfer buffer. This will
ensure even wetting, facilitate proper gel placement and improve
gel contact with the membrane.
Assemble and center sandwich(es) on bottom of cassette (anode)
to ensure even pressure (10mm spaces between sandwiches).
Use a blot roller to remove any trapped air bubbles.
1
2
3
4
Cathode (-)
2 sheets of pre-wet filter paper (combined
thickness not to exceed 1.8mm)
Gel
Membrane
2 sheets of pre-wet filter paper (combined
thickness not to exceed 1.8mm)
Anode (+)
Lock top of the cassette (cathode) into place and slide cassette
into the control unit.
Select Pre-Programmed Methods in the Main Menu.
5
6
7
8
10
Quick Start Guide
Thermo Scientific Pierce G2 Fast Blotter
11
Select the number of gels and gel size (mini or midi) for transfer.
a. 1 mini-gel b. 2 mini-gels or 1 midi-gel
c. 3 mini-gels d. 4 mini-gels or 2 midi-gels
9
12

WARNING After running at high current, the anode and cathode plates can become hot. Use caution when separating
the gels and stacks from the plates. When continuously processing multiple samples at ~5A for a maximum of 2 hours,
allow the cassette to cool for 30 minutes or use multiple cassettes to avoid excessive cassette heating.
WARNING Blotter use outside of the workflows described in this manual may put the operator at risk of dangerous expo-
sure to electrical shock. Do not use this instrument for any purposes or in any configurations not described in this manual.
WARNING The blotter base unit can contain dangerous electricity and is not designed to opened by the user.
Disconnect all power to the base unit before maintenance by a qualified technician.
WARNING Do not overfill the cassette with liquid. Excess liquid can overflow into the base unit and possibly cause
electric shock. Follow the appropriate instructions for reagent amounts and empty any remaining liquid in the cassette
upon run completion.
NOTE A grounded circuit capable of delivering the appropriate current and voltage is required for installation. Electrical requirements can
be located on the rear panel of the blotter base. The blotter electrical system will adjust to the proper voltage for the respective country.
Connect the blotter power cord to the rear left side panel of the device and plug into a grounded power outlet.
Blotter Electrical Parameter Rating
Supply Voltage (VAC) 100-240
Frequency (Hz) 50/60
Maximum Power Rating (W) 168
Fuse (Power Center) T3AL, 250V, 3A
ENVIRONMENTALLY FRIENDLY DISPOSAL
According to EU directive 2002/96/EC on electric and electronic equipment and its implementation into national law, all
electric equipments must be separately collected and environmentally friendly recycled. Alternative disposal: If the owner of
the electric equipments does not return it to the manufacturer, he is responsible for proper disposal at a designated collec-
tion point that prepares the device for recycling according to national recycling laws and regulations. This does not include
accessories and tools without electric or electronic components.
For more details, refer to the full blotter user manual available at www.thermoscientific/pierce
Related Thermo Scientific™Products
84731 Pierce 1-Step Transfer Buffer, 1L
84742 Pierce 1-Step Transfer Buffer, 200mL
84783 Western Blotting Filter Paper, 7cm x 8.4cm, 0.83mm thick, 100 mini-sized sheets
84784 Western Blotting Filter Paper, 8cm x 13.5cm, 0.83mm thick, 100 midi-sized sheets
88600 Western Blotting Filter Paper, 8cm x 10.5cm, 0.83mm thick, 100 mini-sized sheets
88018 Nitrocellulose Membrane, 0.45μm, 30cm x 3.5m roll
88518 PVDF Membrane, 0.45μm, 26.5cm x 3.75m roll
2162534 05/13 Printed in China
© 2013 Thermo Fisher Scientific Inc. All rights reserved. Facebook is a registered trademark of Facebook, Inc.
All other trademarks are the property of Thermo Fisher Scientific Inc. and its subsidiaries.
Life Science Research
Africa/Belgium/Europe/Middle East
[phone]
France 0 800 50 82 15
Germany 0228 9125650
Netherlands 076 50 31 880
Switzerland 0800 56 31 40
UK 0800 252 185
Email: perbio.euromarketing@thermofisher.com
thermoscientific.com/pierce
For other regions, visit
thermoscientific.com/piercedistributors
USA [phone] or [phone]
Customer Assistance
E-mail:Pierce.CS@thermofisher.com
thermoscientific.com/pierce
thermoscientific.com/pierce