Thermo Scientific Sorvall ST 8 User manual

50138912-a February 2013
Thermo Scientific
Sorvall ST 8 Centrifuge
Instruction Manual
Visit us online to register your warranty.
www.thermoscientific.com/labwarranty

Thermo Scientific
Sorvall ST 8 Centrifuge
Instruction Manual
50138912-a February 2013

© 2013 Thermo Fisher Scientific Inc. All rights reserved.
Delrin, TEFLON, and Viton are registered trademarks of DuPont. Noryl is a registered trademark of SABIC.
POLYCLEAR is a registered trademark of Hongye CO., Ltd. Hypaque is a registered trademark of Amersham
Health As. RULON A and Tygon are registered trademarks of Saint-Gobain Performance Plastics. Alconox is a
registered trademark of Alconox. Ficoll is a registered trademark of GE Healthcare. Haemo-Sol is a registered
trademark of Haemo-Sol. Triton X-100 is a registered trademark of Sigma-Aldrich Co. LLC.
All other trademarks are the property of Thermo Fisher Scientific Inc. and its subsidiaries.
Thermo Fisher Scientific Inc. provides this document to its customers with a product purchase to use in the
product operation. This document is copyright protected and any reproduction of the whole or any part of this
document is strictly prohibited, except with the written authorization of Thermo Fisher Scientific Inc.
Country of Origin (manufacturer):
Thermo Fisher (Suzhou) Instruments Co., Ltd.
No. 297 Taishan Road, New District, Suzhou, Jiangsu
P. R. China
Importer for Europe (authorised representative):
Thermo Electron LED GmbH
Robert-Bosch-Straße 1
D - 63505 Langenselbold
Germany
The contents of this document are subject to change without notice. All technical information in this
document is for reference purposes only. System configurations and specifications in this document supersede
all previous information received by the purchaser.
The pictures published within this manual are for reference only. The values shown on your centrifuge might
differ.
Thermo Fisher Scientific Inc. makes no representations that this document is complete, accurate or
errorfree and assumes no responsibility and will not be liable for any errors, omissions, damage or loss
that might result from any use of this document, even if the information in the document is followed
properly.
This document is not part of any sales contract between Thermo Fisher Scientific Inc. and a purchaser. This
document shall in no way govern or modify any Terms and Conditions of Sale, which Terms and Conditions of
Sale shall govern all conflicting information between the two documents.
Original instruction manual 50138912-a printed in February 2013.

WEEE Compliance
This product is required to comply with the European Union’s Waste Electrical & Electronic Equipment
(WEEE) Directive 2002/96/EC. It is marked with the following symbol:
Thermo Fisher Scientific has contracted with one or more recycling or disposal companies in each European
Union (EU) Member State, and these companies should dispose of or recycle this product. See
www.thermo.com/rohsweee for further information on Thermo Fisher Scientific’s compliance with these
Directives and the recyclers in your country.

Contents
Thermo Scientific Sorvall ST 8 Centrifuge 7
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Items Supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Introduction and Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Directives, Standards and Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Functions and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Mains Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Rotor Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Before Setting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Transporting the Centrifuge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Aligning the Centrifuge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Mains Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Shipping the Centrifuge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Switch on Centrifuge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Open Lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Close Lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Rotor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Entering Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Centrifugation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Short-term Centrifugation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Removing the Rotor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Aerosol-tight Rotors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Aligning the Centrifuge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Contents
8Sorvall ST 8 Centrifuge Thermo Scientific
Maintenance and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Cleaning Intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Disinfection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Decontamination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Autoclaving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Thermo Fisher Scientific Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Mechanical Emergency Door Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Troubleshooting by Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
When to Contact Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Chemical Compatibility Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Thermo Scientific Sorvall ST 8 Centrifuge 9
P
Preface
Before starting to use the centrifuge, read through this instruction manual carefully and follow the
instructions.
The information contained in this instruction manual is the property of Thermo Fisher Scientific; it is
forbidden to copy or pass on this information without explicit approval.
Failure to follow the instructions and safety information in this instruction manual will result in the
expiration of the sellers warranty.
Items Supplied
If any parts are missing, please contact your nearest Thermo Fisher Scientific representative.
Intended Use
This centrifuge is a laboratory product used to separate substance mixtures of different densities.
This centrifuge can become an In-vitro-diagnostics device (Directive 98/79/EC), if used together with
the hematocrit rotor and his accessories.
The hematocrit value is determined using the instructions written in the instruction manual of the
hematocrit rotor. The instructions are based upon the reference method following DIN 58933,
allowing to determinate the erythrocyte volume fraction within the blood.
This centrifuge has to be operated by trained specialists only.
Item Quantity Check
Thermo Scientific Sorvall ST 8 Centrifuge 1
Power supply cable 1
Instruction manual 1

Preface
10 Sorvall ST 8 Centrifuge Thermo Scientific
Symbols used on the centrifuge
Symbols used in the manual
Observe the information contained in the instruction manual to keep yourself and your environment
safe.
This symbol refers to general hazards. Follow the instructions in the instruction manual in
any case.
This symbol refers to biological hazards..
Observe the information contained in the instruction manual to keep yourself and your
environment safe.
This symbol refers to information on hazards, described within the manual.
This symbol refers to disconnect mains before transporting or servicing the centrifuge.
This Symbol refers to check, if the rotor is installed correct by lifting it slightly at the handle.
See “Rotor Installation” on page 31.
This symbol refers to general hazards.
CAUTION means that material damage could occur.
WARNING means that injuries or material damage or contamination could occur.
This symbol refers to biological hazards.
This symbol refers to electrical hazards.

Preface
Thermo Scientific Sorvall ST 8 Centrifuge 11
Precautions
A trained specialist can be a laboratory assistant or medical technologist.
WARNING
•Plug the centrifuge only into sockets which have been properly grounded.
•If a hazardous situation occurs, turn off the power supply to the centrifuge and leave
the area immediately.
Note In order to ensure safe operation of the Thermo Scientific Sorvall ST 8 Centrifuge, general
safety regulations must be followed: Mind the regulations in your country.
It is the general obligation of the operator to make sure, that the proper protective clothing is used.
Mind the „Laboratory Biosafety Manual“ of the World Health Organization (WHO) and the
regulations in your country.
The work environment should guarantee the following:
WARNING
•Maintain a radius of at least 30 cm around the centrifuge.
•Implementation of special measures which ensure that no one can approach the
centrifuge for longer than absolutely necessary while it is running.
The power supply must be interrupted in case of an emergency. Turn off the centrifuge at
the main switch. The mains plug must be freely accessible at all times. Pull out the power
supply plug or disconnect the power supply in an emergency.
If the centrifuge is running, press the STOP key to shut it down.
In case of rotor failure the centrifuge can be damaged. Leave the room. Inform customer
service.
WARNING
Do not open the centrifuge, while it is running.
WARNING In any case of mechanical breakdown rotor failure, like burst of the rotor,
breaking bottles or shaft crack, the centrifuge is not aerosol-tight.
Note Not following these instruction can cause damage.

Preface
12 Sorvall ST 8 Centrifuge Thermo Scientific
WARNING
In order to ensure safe operation of the Thermo Scientific Sorvall ST 8 Centrifuge, the
following general safety regulations must be followed:
•The centrifuge should be operated by trained specialists only.
•The centrifuge is to be used for its intended use only.
•Do not move the centrifuge while it is running.
•Do not lean on the centrifuge.
•Do not place anything on top of the centrifuge during a run. This applies also for the
rotor landing pad.
•Use only rotors and accessories for this centrifuge which have been approved by
Thermo Fisher Scientific. Exceptions to this rule are commercially available glass or
plastic centrifuge tubes, provided they have been approved for the speed or the RCF
value of the rotor.
•Contact the the customer service, if the centrifuge and the rotors are in any
conspicious condition, e.g. showing signs of corrosion and/or cracks.
•Do not use rotors which show any signs of corrosion and/or cracks.
•Do not touch the mechanical components of the rotor and do not make any changes
to the mechanical components.
•Use only with rotors which have been properly installed. Follow the instructions on
the Thermo Scientific Auto-Lock rotor exchange in section “Rotor Installation” on
page 31.
•Use only with rotors which have been loaded properly. Follow the instructions given
in the rotor manual.
•Never overload the rotor. Follow the instructions given in the rotor manual.
•Never start the centrifuge when the door is open.
•Never open the door until the rotor has come to a complete stop and this has been
confirmed in the display.
•The door emergency release may be used in emergencies only to recover the samples
from the centrifuge, e.g. during a power failure (see section “Mechanical Emergency
Door Release” on page 54).
•Never use the centrifuge if parts of its cover panels are damaged or missing.
•Do not touch the electronic components of the centrifuge or alter any electronic or
mechanical components.
•Please observe the safety instructions.

Preface
Thermo Scientific Sorvall ST 8 Centrifuge 13
WARNING
Please pay particular attention to the following aspects:
•Location: well-ventilated environment, set-up on a level and rigid surface with
adequate load-bearing capacity.
•Rotor installation: make sure the rotor is locked properly into place before operating
the centrifuge.
•Especially when working with corrosive samples (salt solutions, acids, bases), the
accessory parts and vessel have to be cleaned carefully.
•Always balance the samples.
Centrifuging hazardous substances:
•Do not centrifuge explosive or flammable materials or substances which could react
violently with one another.
•The centrifuge is neither inert nor protected against explosion. Never use the centrifuge
in an explosion-prone environment.
•Do not centrifuge inflammable substances.
•Do not centrifuge toxic or radioactive materials or any pathogenic micro-organisms
without suitable safety precautions.
If centrifuging any hazardous materials mind the „Laboratory Biosafety Manual“ of the
World Health Organization (WHO).
When centrifuging microbiological samples from the Risk Group II (according to the
"Laboratory Biosafety Manual" of the World Health Organization (WHO)),
aerosol-tight biological seals have to be used.
Look on the internet page of the World Health Organization (www.who.int) for the
„Laboratory Biosafety Manual“.
For materials in a higher risk group, extra safety measures have to be taken.
•If toxins or pathogenic substances have gotten into the centrifuge or its parts,
appropriate disinfection measures have to be taken (see “Disinfection” on page 48).
•Highly corrosive substances which can cause material damage and impair the
mechanical stability of the rotor, should only be centrifuged in corresponding protective
tubes.
Remaining risk: Improper use can cause damages, contamination, and injuries
with fatal consequences.
Remaining risk: Improper use can cause damages, contamination, and injuries
with fatal consequences.
Note If used for Foodstuffs machinery, for cosmetics or pharmaceutical products, only use closed
or aerosol-tight containers for centrifugation.

Preface
14 Sorvall ST 8 Centrifuge Thermo Scientific

Thermo Scientific Sorvall ST 8 Centrifuge 15
1
Introduction and Description
Contents
•“Characteristics” on page 16
•“Technical Data” on page 17
•“Directives, Standards and Guidelines” on page 18
•“Functions and Features” on page 19
•“Mains Supply” on page 19
•“Rotor Selection” on page 20

1Introduction and Description
Characteristics
16 Sorvall ST 8 Centrifuge Thermo Scientific
Characteristics
The Thermo Scientific Sorvall ST 8 Centrifuge is an in-vitro diagnostics device according to the
In-Vitro Diagnostics Directive 98/79/EC.
Several rotors with a wide range of tubes can be used.
The set speed is reached within seconds. The maintenance-free induction motor ensures quiet and
low-vibration operation even at high speeds, as well as guaranteeing a very long lifetime.
The user-friendly control panel makes it easy to pre-set the speed, RCF value, running time,
temperature, and running profile (acceleration and braking curves). You can choose between the
display of speed and RCF or the entry mode.
These settings can be changed even while the centrifuge is running.
With the help of the PULSE key, you can also centrifuge a sample for just a few seconds.
The Thermo Scientific Sorvall ST 8 Centrifuge is equipped with various safety features:
•The housing and the interior consist of steel plate, the rotor chamber of stainless steel, while the
front panel is made of high-impact resistant plastic.
•The lid is equipped with a view port and a lock.
•The lid of the centrifuge can only be opened while the centrifuge is switched on and the rotor has
come to a complete stop. The centrifuge cannot be started until the lid has been closed properly.
•The integrated rotor detection systems ensures that no inadmissible speed settings can be
preselected.
•Electronic imbalance recognition
•Lid emergency release: For emergencies only, e.g. during power failures (see “Mechanical
Emergency Door Release” on page 54)

1 Introduction and Description
Technical Data
Thermo Scientific Sorvall ST 8 Centrifuge 17
Technical Data
The technical data of the Thermo Scientific Sorvall ST 8 Centrifuge is listed in the following table.
Tabelle 1-1. Technical Data Thermo Scientific Sorvall ST 8 Centrifuge
Feature Value
Environmental Conditions Designed and intended for indoor use
Altitudes of up to 2,000 m above Sea Level
max. relative Humidity 80 % up to 31 °C; decreasing linearly up to 50 %
relative Humidity at 40 °C.
Permissible Ambient Temperature during Operation +2 °C to +35 °C
Permissible Ambient Temperature during Storage and
Shipping
-10 °C to +50 °C
Overvoltage Category II
Pollution Degree 2
Heat Dissipation Ventilated
0,31 kWh/h / 1060 Btu/h / 1120 kJ/h
IP 20
Max Running Time 99 h 59 min 50 sec, hold
Max Speed nmax 16000 rpm (depending on the rotor)
Min Speed nmin 300 rpm
Max RCF Value at nmax 24327xg
Maximum Kinetic Energy 8.12 < kJ
Noise Level at Maximum Speed < 58 dB (A) TX-150 Rotor; < 61 MicroClick 24x2 Rotor
Dimensions Ventilated
Height
Height with Lid Open
Width
Depth
310 mm
660 mm
370 mm
490 mm
Weight without Rotor 35 kg

1Introduction and Description
Directives, Standards and Guidelines
18 Sorvall ST 8 Centrifuge Thermo Scientific
Directives, Standards and Guidelines
Tabelle 1-2. Directives, Standards and Guidelines
Tension /
Frequency Directive Produced and inspected according to the following standards and guidelines
Europe
230V 50/60Hz
•2006/95/EC Low Voltage Directive
•2006/42/EC Machinery
•2004/108/EC Electromagnetic compatibility
(emc)
•2011/65/EC RoHS Directive on the
Restriction of the use of certain Hazardous
Substances in electrical and electronic
equipment.
•2002/96/EC WEEE: Directive on Waste
Electrical and Electronic Equipment
•1907/2006 REACH Regulation on
Registration, Evaluation, Authorization and
Restriction of Chemicals (including
requirements for SVHC, substances of very
high concern)
EN 61010-1, 2nd Edition
EN 61010-2-020, 2nd Edition
EN 61010-2-101, 2nd Edition
EN 61326-1 Class B
EN 61326-2-6
EN ISO 13485
USA &
Canada
230V 60Hz
120V 60Hz
FDA Device Class 1 Product code JQC
(centrifuges for clinical use)
CAN/CSA-C22.2 No. 61010-1-04
UL Std. No. 61010-1, 2nd Edition)
CAN/CSA-C22.2 No. 61010-2-020-09-Part 2-020
IEC 61010-2-020, 2nd Edition
IEC 61010-2-101, 2nd Edition
EN ISO 13485
Japan
100V 60Hz
100V 50Hz
China
230V 50/60Hz
IEC 61010-1, 2nd Edition
IEC 61010-2-020, 2nd Edition
IEC 61010-2-101, 2nd Edition
EN 61326-1 Class B
EN 61326-2-6
EN ISO 13485

1 Introduction and Description
Functions and Features
Thermo Scientific Sorvall ST 8 Centrifuge 19
Functions and Features
The following table gives an overview of the important functional and performance characteristics of
the Thermo Scientific Sorvall ST 8 Centrifuge.
Mains Supply
The following table contains an overview of the electrical connection data for the Thermo Scientific
Sorvall ST 8 Centrifuge. This data is to be taken into consideration when selecting the mains
connection socket.
Tabelle 1-3. Functions and Features
Component / Function Description / Features
Structure / Housing Galvanized steel chassis with armoured plating
Chamber Stainless steel
Drive Induction drive without carbon brushes
Keys and display Easy-to-clean keypad and display surface
Controls Microprocessor-controlled
Internal memory The most recent data is saved
Functions RCF-selection
Acceleration / braking profiles Standard and Soft Acceleration/Deceleration
Rotor recognition Automatic / Electric
Imbalance recognition Electronic, contingent on rotor and speed
Lid lock Lid is locking, when being pressed down
Tabelle 1-4. Electrical connection data of the Thermo Scientific Sorvall ST 8 Centrifuge
Cat.
Mains
voltage
± 10 %
Frequency Rated
current
Power
consumption Equipment fuse Building fuse
75007221 ventilated 230 V 50 / 60 Hz 2,0 A 310 W 5 AT 16 AT
75007220 ventilated 120 V 60 Hz 5,0 A 310 W 10 AT 15 AT

1Introduction and Description
Rotor Selection
20 Sorvall ST 8 Centrifuge Thermo Scientific
Rotor Selection
The Thermo Scientific Sorvall ST 8 Centrifuge is supplied without a rotor.
Various rotors are available to choose from.
The technical data of the rotors and the corresponding adapters and reduction sleeves for various
commercially available containers can be found in the corresponding rotor operating manuals.
For more information visit our website at: http://www.thermoscientific.com
Thermo Scientific Rotors Part No.
TX-150 swinging bucket rotor 75005701
TX-150 round buckets 75005702
TX-150 50mL conical buckets 75005703
TX100S clinical swinging bucket rotor with sealed carriers 75005704
TX100 clinical swinging bucket rotor with carriers 75005705
M10 microplate swinging bucket rotor 75005706
M10 with buckets 75005723
MT12 microtube swinging bucket rotor 75005600
HIGHConic III fixed angle rotor 75005709
CLINIConic fixed angle rotor 75003623
MicroClick 24x2 microtube rotor 75005715
MicroClick 30x2 microtube rotor 75005719
8x8 PCR Strip rotor 75005720
Hematocrit rotor 75005733

Thermo Scientific Sorvall ST 8 Centrifuge 21
2
Before Use
Contents
•“Before Setting up” on page 22
•“Transporting the Centrifuge” on page 23
•“Location” on page 22
•“Aligning the Centrifuge” on page 23
•“Mains Connection” on page 24
•“Storage” on page 24