Timago FS 913L User manual

1
INSTRUCTIONS FOR USE
2-function folding frame
Product code: FS 913L
1. Characteristics
2-function folding walker is made of crosswise reinforced aluminium
frame. The walker fulfils 2 functions: the rigid and the reciprocating.
Owing to the latter one, it is possible to move the sides alternatively
without the need to lift the walker. The walker possesses locking clips
which are used to switch the functions, wide area of support as well as
stable and long range of walking. Soft and foamed handgrips provide
proper stabilization and comfortable use. Owing to adjustable legs, the
height of the walker can be adjusted according to user’s height. Rubber
tips prevent the walker from sliding. Folded walker takes little space,
and thus, can be easily stored and transported.
Elements of the walker:
a. Handgrip
b. Frame folding clip
c. Rigid function
d. Reciprocating function
e. Height adjustment – locking pin
f. Anti-sliding rubber tip
2. Application
2-function walker is ancillary equipment designed for people with
reduced mobility who need stable support and help while walking. It is
also recommended to the elderly as an aid in keeping balance,
improving walking comfort and ensuring safety from falling. The use of
the walker affects positively on the return to activity of the people with
lower limbs diseases and with locomotion or tilting to erect position
problems.

2
3. Assembly
Unfolding and folding
•To unfold the walker, pull the sides apart to the maximum
position until the handgrips are locked.
•To fold the walker, press the plastic element located in the middle
on the transverse frame and fold the sides.
Height adjustment
•The height should be set on such a level that the user, who is
leaning against the handgrips, stands upright, as far as he or she is
able to, with his or her shoulders in rest position and with slightly
bent elbows. It is inadvisable to hang on the walker with all the
body weight.
•To adjust the height of legs, press the metal pin, select
appropriate height of the leg, and lock the position of the legs
relative to each other. The legs are adjustable in 2.5 cm
increments.
Note! The pins must be set on the same level in each leg.
Selection of functions
•Rigid function – remove locking clips from the upper horizontal
element which reinforces the frame, and place them into the
openings which are located on the same height level but on the
vertical element of the frame.
•Reciprocating function – place the locking clips again into the
mounting openings on the horizontal element.
4. Technical data
Overall width 46 cm
Inner width 44 cm
Overall depth 47 cm
Height adjustment 78-96 cm

3
Weight 2.4 kg
Maximum capacity 100 kg
Frame colour silver, bronze
5. Notes
Timago International Group does not bear responsibility of improper
use of the walker, failure to comply safety regulations and misuse.
6. Maintenance
•Clean the frame of the walker with damp cloth using only water
and mild detergents. Dry thoroughly.
•Do not use for cleaning: strong polishing and abrasive agents,
strong detergents, bleach, petrol or solvents (it may cause frame
damage, visible defects and in consequence - loss of warranty
rights).
•Remove impurities from moving parts of the walker (hinges,
clamping screws, locks).
7. Storage and transport conditions
Device should not be exposed to direct sunlight, water or moisture.
8. Warranty information
All products distributed by our company are covered by a warranty, the
terms of which are described in the warranty card available on our
website. Please contact the retailer from whom you purchased the
product. Please, keep in mind that for warranty purposes, the proof of
purchase (receipt or invoice) should be retained
9. Labels
Reference
number
Manufacturer

4
LOT number Manufacture date
Serial number Medical device
Note
Please read the
instruction
The manufacturer checked for compliance with
essential medical devices requirements.
Our complete line of products is available from our distributors.
Learn more at: www.timago.com. Thank you for choosing Timago!
Timago International Group
Spółka z o.o. i Spółka – Spółka komandytowa
ul. Karpacka 24/12
43-316 Bielsko-Biała, Polska
T.: [phone]
F.: [phone]
E.: [e-mail]
Rev. II, date 20.05.2021