Tone SIMPLE TORQON XT-STC7TE User manual

Part: XT-STC7TE
Part: XT-STC11TE
Sockets not included
SIMPLE TORQON
Electric Torque Control Wrench
STC-TYPE
Bolting made Safe,
Easy and Accurate
Torque Control

SIMPLE TORQON (STC-type)
Supplied by
HOBSON ENGINEERING
10 Clay Place, Eastern Creek NSW 2766
Phone: [phone]
www.hobson.com.au
[email protected] * Specications and design are subject to change without notice
FEATURES and BENEFITS
Model No. STC3TE STC5TE STC7TE STC11TE STC12TE STC21TE
Max.Currenct 13.5A / 6.5A 13.5A / 6.5A 13.5A / 6.5A 15A / 7.5A 15A / 7.5A 12A / 6A
Max.Power Consumption 1100W 1100W 1110W 1400W 1400W 1100W
Frequency 50-60Hz 50-60Hz 50-60Hz 50-60Hz 50-60Hz 50-60Hz
Controllable Torque Range 150~300 300~500 350~700 500~1100 600~1200 1000~2100
Repeated Accuracy ±5±5±5±5±5±5
Free Rotation min (RPM) 28 25 17 15 16 4
Weight (mainbody) Kg 4.6 5.3 6.2 9.0 9.0 19.0
Square Drive 3/4” 3/4” 1” 1” 1” 1-1/2”
Accessories 1 pc. of Metal Case, Instruction Manual & Hex key wrench
1pc. of L-foot, I-bar & Q-connector
SPECIFICATIONS
▫S ØD W L L1 L2 H H1 H2 H3
STC3AE-TE 3/4” 60 85 250 280 225 250 230 110 67
STC5AE-TE 3/4” 70 85 255 285 230 255 230 110 67
STC7AE-TE 1” 75 85 270 315 240 260 270 115 64
STC11AE-TE 1” 85 105 325 370 295 285 290 130 72
STC12AE-TE 1” 85 105 325 370 295 285 290 130 72
STC21AE-TE 1-1/2” 121 105 415 485 375 305 370 180 98
EXTERNAL DIMENSION unit : mm
240V
1. Easy Operation
Simply turn the setting dial to the Nm required.
2. High Accuracy
Repeated tightening torque accuracy ±5%.
3. Rotation in both directions
Torque control, soft start and free-joint mechanism operate
in both clockwise and anti-clockwise directions.
4. No Vibration
No impact during use.
5. Two Reaction Arms
L-shaped arm and Straight bar arm. No opposing force
required by operator.
6. Automatic shut-off at present torque
7. Low Noise Level
XT-STC7TE
Note: Only impact sockets should be used.

SIMPLE TORQON (STC-type)
HOW TO OPERATE
Refer to the full instruction manul included with the tool.
For safe use
Supplied by
HOBSON ENGINEERING
10 Clay Place, Eastern Creek NSW 2766
Phone: [phone]
www.hobson.com.au
[email protected]
1. Conrm rotating directions of socket and
reaction-bar (counteracting).
2. Watch distance between nut and reaction-bar.
Select L-foot or I-bar (Straight-bar) and mount in
Q-connector.
3. Mount Q-Connector on wrench drive, then mount
impact socket securely.
6. Squeeze trigger switch. When required
torque has been reached, wrench stops and
tightening is over.
Attention
Some error is inevitable due to Torque-Coefcient
that varies by coating on the bolts and nuts when
setting required torque.
If high precision torque setting is required, the use
of dial-type torque wrench is recommended.
Tightening
* Specications and design are subject to change without notice
Press trigger intermittently untill the reaction-bar
touches the prop (support)
4. Adjust torque setting dial to required torque value
in Nm.