TOPP C30S/230V User manual

C30S
INSTALLATION AND USE INSTRUCTIONS
CHAIN ACTUATOR FOR
WINDOW AUTOMATION
PATENTED
BEFORE INSTALLING AND USING THE ACTUATOR, IT IS
COMPULSORY FOR THE INSTALLER AND THE USER TO READ
AND UNDERSTAND THIS MANUAL IN ALL ITS PARTS.
THIS MANUAL IS INTEGRAL PART OF THE ACTUATOR
AND MUST BE PRESERVED FOR FUTURE REFERENCE
UNTIL DEMOLITION OF THE SAME.
VER.0.0 REV.02.18
P/N 0P5311
original instructions

INDEX
1- EC DECLARATION OF INCORPORATION OF PARTLY COMPLETED
MACHINERY
........................................................................................................................page 04
2- GENERAL REMARKS
2.1- General instructions..........................................................................................page 05
2.2- Installer and user ..............................................................................................page 05
2.3- Technical assistance.........................................................................................page 05
2.4- Reserved rights ................................................................................................page 06
2.5- Description of personnel...................................................................................page 06
3- TECHNICAL DESCRIPTION
3.1- Rating plate and "CE" marking.........................................................................page 07
3.2- Denomination of the components and dimensions ..........................................page 08
3.3- Technical data...................................................................................................page 09
3.4- Formulas for the calculation of thrust force or tractive force ............................page 10
3.5- Destination of use.............................................................................................page 10
3.6- Use Limits.........................................................................................................page 11
3.7- Package............................................................................................................page 11
4- SAFETY
4.1- General instructions .........................................................................................page 13
4.2- Safety Devices .................................................................................................page 13
4.2.1- Protections against electric hazard ...............................................................page 13
4.3- Safety plates.....................................................................................................page 14
4.4- Residual risks ...................................................................................................page 14
5- INSTALLATION
5.1- General instructions .........................................................................................page 15
5.2- Top hung windows............................................................................................page 18
5.3- Bottom hung windows ......................................................................................page 19
5.4- Electrical Connections......................................................................................page 20
5.5- Control devices.................................................................................................page 21
5.6- Emergency procedures ....................................................................................page 22
6- USE AND OPERATION
6.1- Use of the actuator ...........................................................................................page 23
6.2- Smart Reset System (SAI)..............................................................................page 24
7- MAINTENANCE
7.1- General instructions .........................................................................................page 25
8- DEMOLITION
8.1- General instructions .........................................................................................page 25
9- SPARE PARTS AND ACCESSORIES UPON REQUEST
9.1- General instructions .........................................................................................page 25
FIGURES
........................................................................................................................page 26
3
C30S
INSTALLATION AND USE ISTRUCTIONS

4
C30S
INSTALLATION AND USE ISTRUCTIONS
1- EC DECLARATION OF INCORPORATION OF PARTLY COMPLETED MACHINERY
ORIGINAL
The undersigned, in the name of and
behalf of the following company
Topp S.r.l.
Via Galvani, 59
36066 Sandrigo (VI)
Italia
herewith declares that the person authorised to compile the technical file is
Name: Bettiati Roberto - Topp S.r.l.
Address: via Galvani,59 36066 Sandrigo (VI)
and that to the partly completed machinery
CHAIN ACTUATOR FOR WINDOW AUTOMATION
Type: C30S
Model: C30S/230V - C30S/24V
the following essential requisites of the
2006/42/EC Machinery Directive (including all applicable amendments)
have been applied and fulfilled: Enclosure I: 1.5.1; 1.5.2; 1.5.10; 1.5.11
that the relevant technical documentation is compiled in accordance with part B of Annex VII of the above
mentioned Machinery Directive..
The above identified partly completed machinery is also in conformity with the all the relevant provisions
of the following directives (including all applicable amendments)
EMC Directive 2014/30/EU
RoHS II Directive 2011/65/EU
The following harmonised standards have been applied:
EN 60335-2-103:2015 (applicable parts)
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:2015
EN 61000-6-2:2005.
EN 61000-6-3:2007 + A1:2011 + AC:2012.
EN 50581:2012
and the following technical documents:
EN 62233:2008
The undersigned also undertakes the obligation, in response to a duly reasoned request by the national
market surveillance authorities, to transmit to the a.m. authorities, in electronic or paper format, the
relevant technical documentation on the partly completed machinery.
The above identified partly completed machinery must not be put into service until the final machinery
into which it is to be incorporated has been declared in conformity with the provisions of the above
mentioned Machinery Directive.
This declaration of conformity is issued under the sole responsibility of the manufacturer.
Date: Sandrigo01/02/2018 Signature: Matteo Cavalcante
Amministratore ................................................................

5
C30S GENERAL REMARKS -2
2.1- GENERAL INSTRUCTIONS
BEFORE INSTALLING AND USING THE ACTUATOR, IT IS COMPULSORY THAT THE
INSTALLER AND THE USER CAREFULLY READ AND UNDERSTAND THIS MANUAL
IN ALL ITS PARTS.
THIS MANUAL IS INTEGRAL PART OF THE ACTUATOR AND MUST COMPULSORILY
BE PRESERVED FOR FUTURE REFERENCE.
THE MANUFACTURER HAS NO LIABILITY FOR ANY EVENTUAL DAMAGE TO
PERSONS, ANIMALS AND THINGS DUE TO THE INOBSERVANCE OF THE
PRESCRIPTIONS DESCRIBED IN THIS MANUAL.
IN ORDER FOR THE AUTOMATION UNIT TO OPERATE CORRECTLY, WE
RECOMMEND CARRYING OUT PERIODICAL MAINTENANCE ON IT, AS INDICATED IN
PAR. 7.1 OF THIS MANUAL.
THE WARRANTY ON THE ACTUATOR WILL NOT BE HONORED IF PRODUCT IS NOT
INSTALLED AND USED ACCORDING TO THE INSTRUCTIONS PROVIDED AND THE
REGULATIONS SHOWN IN THIS INSTRUCTION MANUAL AND IF IT IS USED WITH NON-
GENUINE PARTS, ACCESSORIES, SPARE PARTS AND/OR CONTROL/FEEDING UNITS.
2.2- INSTALLER AND USER
THE ACTUATOR INSTALLATION CAN BE PERFORMED EXCLUSIVELY BY
COMPETENT AND QUALIFIED TECHNICAL PERSONNEL SATISFYING THE
PROFESSIONAL AND TECHNICAL REQUIREMENTS FORESEEN BY THE LAWS IN
FORCE IN THE COUNTRY OF INSTALLATION.
THE INSTALLATION TECHNICIAN SHALL ACCEPT FULL RESPONSIBILITY FOR ANY
INSTALLATION ERRORS AND FOR ANY FAILURE TO ADHERE TO THE
INSTRUCTIONS PROVIDED IN THIS MANUAL. THE INSTALLATION TECHNICIAN
SHALL THEREFORE BE EXCLUSIVELY LIABLE FOR ANY DAMAGES CAUSED TO
USERS AND/OR THIRD PARTIES THAT MAY ARISE AS A RESULT OF INCORRECT
INSTALLATION.
THE ACTUATOR CAN BE USED EXCLUSIVELY BY A USER ACTING IN COMPLIANCE
WITH THE INSTRUCTIONS CONTAINED IN THIS MANUAL AND/OR IN THE MANUAL
OF THE ACTUATOR CONTROL DEVICE (e.g.: CONTROL UNIT).
2.3- TECHNICAL ASSISTANCE
Contact the installation technician or retailer for assistance.
INSTALLATION AND USE ISTRUCTIONS

2.4- RESERVED RIGHTS
The reserved rights on this manual "Installation and use instructions" remain property of
the Manufacturer.
Each information herein contained (text, drawings, diagrams, etc.) is reserved.
None part of this manual can be reproduced and disclosed (totally or partially) by any
reproduction means (photocopies, microfilms or other) without written authorization of
the Manufacturer.
2.5- DESCRIPTION OF PERSONNEL
USERS MUST NEVER PERFORM OPERATIONS RESERVED FOR MAINTENANCE
PEOPLE OR SPECIALISED TECHNICIANS. THE MANUFACTURER DECLINES ALL
LIABILITY FOR DAMAGE DERIVING FROM FAILURE TO OBSERVE THE ABOVE
REQUIREMENTS.
Specialised electrician:
A specialised electrician must be able to install the actuator, start it and operate it both
in normal conditions and in the maintenance mode; he/she is qualified to perform all
electrical and mechanical adjustment and maintenance operations. He/she is allowed
to work on live electrical cabinets and junction boxes.
User:
specialised person capable of operating the actuator under normal conditions by using
the relative controls. He/she must also be able to operate with the actuator under
“maintenance” in order to perform simple routine maintenance operations (cleaning),
and start or reset the actuator following an unscheduled stop.
6
2- GENERAL REMARKS
INSTALLATION AND USE ISTRUCTIONS
C30S

3.1- RATING PLATE AND "CE" MARKING
The "CE" marking certifies the compliance of the machine with the essential safety and
health requirements foreseen by the product European Directives.
The rating plate is an adhesive plate in polyester, silk-screen printed in black, having the
following size: L= 50 mm - H= 36 mm.
It is applied externally on the actuator. The plate bears in readable and indelible way the
following data:
• logo and address of the manufacturer
• type and model
• voltage and intensity of power supply (V - A)
• type of service S (min)
2
• absorbed electric power P (W)
• thrust and tractive force F (N)
• idle translation speed (mm/s)
• protection degree (IP)
• symbol of double insulation (only for mod. C30S/230V)
• "CE" marking
• symbol of “WEEE” Directive 2002/96/CE
• serial number
7
C30S TECHNICAL DESCRIPTION -3
INSTALLATION AND USE ISTRUCTIONS

3.2- DENOMINATION OF THE COMPONENTS AND DIMENSIONS
Dimensions in mm LEGEND:
1) Quick coupling
2) Slot side indicator
3) Bracket for bottom hung opening
4) Opening stroke adjustment
switch I= 200 mm; II= 380 mm
5) Connection bracket to the frame
6) Actuator
7) Chain adjustment end
8) Chain end adjustment screw
9) Power supply cable
8
C30S
3- TECHNICAL DESCRIPTION
INSTALLATION AND USE ISTRUCTIONS
Fig. 1
7
8
6
80
335.2
101
3
103
96.5 6.5
1.5
34.12
20
11
Ø5
Ø5
11
54
19
4
2
1
16
86
15
4
49
37
46
53
46
9
5
1 12 12 7
310
276

3.3- TECHNICAL DATA
Tab. 1 contains the technical data characterising the actuators.
9
C30S TECHNICAL DESCRIPTION -3
INSTALLATION AND USE ISTRUCTIONS
MAXIMUM APPLICABLE THRUST LOAD 300 N 300 N
MAXIMUM APPLICABLE TRACTIVE LOAD 300 N 300 N
MAXIMUM THRUST LOAD APPLICABLE ON
TWO SYNCHRONIZED AUTOMATIONS.
500 N
500 N
MAXIMUM TRACTIVE LOAD APPLICABLE ON
TWO SYNCHRONIZED AUTOMATIONS
500 N
500 N
IDLE TRANSLATIO N SPEED 9,5 mm/s 9,5 mm/s
DURATION OF THE IDLE S TROKE 40 s 40 s
TYPE OF SERVICE S2 (1)
3 min 3 min
ADJUSTABLE STROKES ON OUTLET (2)
200 mm / 380 mm
ADJUSTMENT OF THE WINDOW FRAME CONNECTION
AUTOMATIC
MAX. OVERLAPPED PART “D” 50 mm
OPERATING TEMPERATURE -5°C ÷ 50°C
ACTUATOR WEIGHT WITH BRACKETS 1,1 kg
GROSS WEIGHT 1,5 kg
SYNCHRONIZ. TWO ACTUATORS ON THE SAME WINDOW Yes
POWER SUPPLY VOLTAGE 230 V ~ 50 Hz 24 V ± 10%
ABSORBED CURRENT 0,15 A 0,55 A
ABSORBED POWER WITH LOAD 25 W 14 W
PROTECTION AGAINST ELECTRIC SHOCKS Class II Class III
PROTECTION DEGREE OF ELECTRIC DEVICES IP30
PARALLEL CONNECTION OF MORE THAN ONE ACTUATOR
Yes
(See wiring diagram)
ADJUSTABLE STROKES ON OUTLET 200 mm 380 mm
MINIMUM HEIGHT OF THE WINDOW FRAME (3)
Posion
assembly
brackets
0 Top hung 250 mm 500 mm
Boom hung
350 mm 1000 mm
1 Top hung 250 mm 400 mm
2 Top hung 350 mm 500 mm
3Boom hung 500 mm 950 mm
MINIMUM DISTANCE BETWEEN ACTUATOR 60 mm
C30S/230V C30S/24V
(1) Service of limited duration according to EN 60034
(2) Tolerance on the tripping precision of the limit switch at output: ± 10 mm
(3) Distance of the actuator from the window opening hinge valid only with max. stroke 380 mm
Tab. 1

3.5- DESTINATION OF USE
THE ACTUATOR HAS BEEN DESIGNED AND MANUFACTURED TO PERFORM, BY
MEANS OF A CONTROL DEVICE, THE OPENING AND CLOSING OF TOP HUNG
WINDOWS, BOTTOM HUNG WINDOWS, PIVOT WINDOWS, AND SKYLIGHTS.
3.4- FORMULAS FOR THE CALCULATION OF THRUST AND
TRACTIVE FORCE
Top hung windows (A) or
bottom hung windows (B)
F = Force necessary for opening or
closing
P = Weight of the window
(only movable part)
C = Window opening stroke
H = Window height (only movable part)
F = (0,54 x P) x ( )
C
H
P
F
H
C
B
P
F
H
C
A
F
P
Horizontal domes or skylights
F = Force necessary for opening or closing
P = Weight of the skylight or dome
(only movable part)
F = 0,54 x P
The C30S Chain actuator is equipped with the latest TOPP system for the coordinated
synchronization of the chain movement. The electronic speed control is fully automatic and
requires no external control unit; just connect the yellow/white/blue cables as per wiring diagram at
the back of the manual to achieve the synchronized mode. The Smart Reset System (SAI) has
also been included which adjusts the closure of the window in an optimum manner.
The C30S chain actuator is mounted when you need two or more attachment points because the
window is particularly heavy or wide and only one actuator would not allow perfect closure of the
window. It should be remembered that the force exerted by the actuators individually is the same
as a similar C30 actuator; for example, by mounting two actuators the force applied to the window
is, therefore, doubled. The window is moved in a uniform, synchronized and coordinated manner
with no interruptions and/or speed changes in the actuators' operation. In the event of any failure of
one of the actuators due to a mechanical or electrical fault, the others also stop operating,
guaranteeing that the window remains intact.
10
C30S
3- TECHNICAL DESCRIPTION
INSTALLATION AND USE ISTRUCTIONS
Fig. 2
Fig. 3

3.6- USE LIMITS
The actuator has been designed and manufactured exclusively for the destination of
use given in par. 3.5, therefore, any other type of use is strictly forbidden in order to
assure in any moment the safety of the installer and of the user, as well as the efficiency
of the actuator itself.
Check carefully all environmental conditions (temperature, humidity, wind, snow,
potential chemical agents, etc.) and installation settings (misaligned fitting of brackets
and attachment to the frame, frictions produced by hinges or gaskets, use of self-
balancing window stays, etc.) it is recommended that they not exceed the actuator
performances shown in the technical table. If they do, please find an alternative and
more suitable product for your application.
IT IS STRICTLY FORBIDDEN TO USE THE ACTUATOR FOR IMPROPER USES OTHER
THAN THE ONE FORESEEN BY THE MANUFACTURER (SEE PAR. 3.5).
IT IS STRICTLY FORBIDDEN TO INSTALL THE ACTUATOR ON THE EXTERNAL SIDE
OF THE WINDOW FRAME SUBJECT TO ATMOSPHERIC AGENTS (RAIN, SNOW,
ETC.).
THE USE OF THE ACTUATOR IN ENVIRONMENTS WITH POTENTIALLY EXPLOSIVE
ATMOSPHERE IS STRICTLY FORBIDDEN.
IT IS COMPULSORY TO KEEP THE PACKAGE AND THE ACTUATOR OUT OF REACH
OF CHILDREN.
3.7- PACKAGESTANDARD
Each standard package of the product (cardboard box) contains (Fig. 4):
No.1 Actuator equipped with power supply cable;
No.1 Window frame connection bracket (Ref. A);
No.1 Bracket for bottom hung opening (Ref. B);
No.1 Small parts package (quick coupling, No.2 bracket fastening lateral screws, No.7
screws AF Ø4.2 x 19 mm for fastening the bracket to the window frame) (Ref. C);
No.1 (2 mm) Allen wrench (Ref. D);
No.1 Installation and use instructions (Ref. E);
No.1 Adhesive drilling template (Ref. F);
No.1 Safety Plate (Fig. 5).
MAKE SURE THAT THE ABOVE DESCRIBED COMPONENTS ARE CONTAINED IN
THE PACKAGE, AS WELL AS THAT THE ACTUATOR HAS NOT BEEN DAMAGED
DURING TRANSPORT.
SHOULD ANY ANOMALY BE DETECTED, IT IS FORBIDDEN TO INSTALL THE
ACTUATOR, AND IT IS COMPULSORY TO REQUIRE TECHNICAL ASSISTANCE FROM
YOUR DEALER OR THE MANUFACTURER.
THE PACKAGING (PAPER, PLASTIC, ETC.) HAS TO BE DISPOSED ACCORDING TO
THE LAWS IN FORCE.
EX
11
C30S TECHNICAL DESCRIPTION -3
INSTALLATION AND USE ISTRUCTIONS

12
C30S
3- TECHNICAL DESCRIPTION
INSTALLATION AND USE ISTRUCTIONS
A
F
D
Fig. 4
E
BC

4.1- GENERAL INSTRUCTIONS
OPERATORS MUST BE INFORMED OF ACCIDENT RISKS, SAFETY DEVICES AND
THE GENERAL ACCIDENT PREVENTION REGULATIONS ESTABLISHED BY
INTERNATIONAL DIRECTIVES AND BY THE LAW IN FORCE IN THE COUNTRY OF
USE. ALL OPERATORS MUST STRICTLY COMPLY WITH THE ACCIDENT
PREVENTION REGULATIONS IN FORCE IN THE COUNTRY OF USE.
DURING HANDLING AND INSTALLATION OF THE PARTS, THE PERSONNEL SHALL
BE EQUIPPED WITH SUITABLE PERSONAL PROTECTION EQUIPMENT (PPE) SO AS
TO PERFORM THE WORKS REQUIRED UNDER SAFE CONDITIONS.
DO NOT REMOVE OR ALTER THE PLATES PLACED ON THE ACTUATOR BY THE
MANUFACTURER.
IF THE WINDOW FRAME IS ACCESSIBLE FROM OR INSTALLED AT A HEIGHT OF
LESS THAN 2.5 m FROM THE GROUND, AND IF IT CAN BE COMMANDED BY AN
UNTRAINED USER OR WITH A REMOTE CONTROL DEVICE, FIT AN EMERGENCY
STOP SYSTEM WHICH AUTOMATICALLY CUTS IN TO PREVENT THE RISK OF
CRUSHING OR DRAGGING PARTS OF THE BODY INSERTED BETWEEN THE
MOVING AND FIXED PARTS OF THE WINDOW FRAME.
ANY TAMPERING WITH OR UNAUTHORISED REPLACEMENT OF ONE OR MORE
PARTS OR COMPONENTS OF THE ACTUATOR, OR THE USE OF UNORIGINAL
ACCESSORIES AND CONSUMABLES, MAY INCREASE THE RISK OF ACCIDENT
AND THUS RELIEVES THE MANUFACTURER OF ALL CIVIL AND PENAL LIABILITY
EXTRAORDINARY AND ROUTINE MAINTENANCE OPERATIONS INVOLVING THE
TOTAL OR PARTIAL DISMOUNTING OF THE ACTUATOR MAY ONLY BE PERFORMED
AFTER DISCONNECTING IT FROM THE POWER SUPPLY.
THIS APPLIANCE MAY NOT BE USED BY PERSONS (CHILDREN INCLUDED) WITH
REDUCED PHYSICAL, SENSORIAL OR MENTAL CAPACITIES, OR INEXPERT
PEOPLE, UNLESS THEY ARE SUPERVISED AND TAUGHT HOW TO USE IT BY A
PERSON RESPONSIBLE FOR THEIR SAFETY. CHILDREN MUST BE CONTROLLED
TO MAKE SURE THEY DO NOT PLAY WITH THE APPLIANCE.
4.2- SAFETY DEVICES
4.2.1- PROTECTION AGAINST ELECTRIC HAZARD
The actuator is protected against electric hazard due to direct and indirect contacts.
The protection measures against direct contacts aim at protecting people against
hazards due to contact with active parts, usually live parts; while the protection
measures against indirect contacts aim at protecting people against hazards due to
conducing part, which are usually insulated, but could become live in case of failure
(insulation failure).
SAFETY -4
C30S
13
INSTALLATION AND USE ISTRUCTIONS

14
C30S
4- SAFETY
INSTALLATION AND USE ISTRUCTIONS
The adopted protection measures are the following:
1) Insulation of live parts by means of a plastic material body;
2) Enclosure with suitable protection degree;
3) Only for the mod. C30S/230V provided with protection against electric shocks:
Protection of passive type given by the use of components with double insulation,
also called components of class II or with equivalent insulation.
4.3- SAFETY PLATES
IT IS FORBIDDEN TO REMOVE, MOVE, SPOIL OR IN ANYWAY REDUCE THE
VISIBILITY OF THE SAFETY PLATES. FAILURE TO OBSERVE THE ABOVE MAY
CAUSE SERIOUS HARM TO PEOPLE AND DAMAGE TO PROPERTY. THE
MANUFACTURER DECLINES ALL LIABILITY FOR ANY DAMAGE CAUSED BY THE
FAILURE TO OBSERVE THE ABOVE REQUIREMENT.
Fig. 5 illustrates the safety plate: this must applied directly to the outside of the
actuator or near it and always in a position where it can be seen by the installer and/or
operator.
4.4- RESIDUAL RISKS
The installer and the user are herewith informed that after the actuator has been
installed on the window, the actuator drive can accidentally generate the following
residual risk:
Residual risk: Hazard of squashing or dragging of body parts inserted between the
movable and the fix part of the window frame.
Exposure frequency: Accidental and when the installer or the user decides to perform
a wrong voluntary action.
Severity of the damage: Light lesions (usually reversible).
Adopted measures: Before enabling the device, it is compulsory to verify that near the
window there are not persons, animals or things whose safety may be accidentally
jeopardized. During actuator operation, it is compulsory to be in a safe control position
assuring visual control on the window movement.
Fig. 5
MACCHINA AD AVVIAMENTO AUTOMATICO
AUTOMATIC MACHINE
PRIMA DI INSTALLARE E UTILIZZARE L'ATTUATORE È OBBLIGATORIO CHE L'INSTALLATORE E
L'UTILIZZATORE LEGGANO E COMPRENDANO IN TUTTE LE SUE PARTI IL MANUALE
THE INSTALLER AND USER MUST READ AND UNDERSTAND ALL PARTS OF THIS MANUAL BEFORE
INSTALLING AND USING THE ACTUATOR.
PERICOLO ATTENZIONE ALLE MANI
BEWARE OF YOUR HANDS
ATTENZIONE MACCHINA AD AVVIAMENTO AUTOMATICO CON COMANDO A DISTANZA
ATTENTION! AUTOMATIC MACHINE WITH REMOTE CONTROL DEVICE
IT
EN

15
C30S
5.1- GENERAL INSTRUCTIONS
THE ACTUATOR INSTALLATION CAN BE PERFORMED EXCLUSIVELY BY
COMPETENT AND QUALIFIED TECHNICAL PERSONNEL SATISFYING THE
PROFESSIONAL AND TECHNICAL REQUIREMENTS FORESEEN BY THE LAWS IN
FORCE IN THE COUNTRY OF INSTALLATION.
THE ACTUATOR PERFORMANCE MUST BE SUFFICIENT TO ASSURE THE
CORRECT MOVEMENT OF THE WINDOW. IT IS COMPULSORY TO VERIFY THE
THRUST OR TRACTIVE FORCE ACCORDING TO THE TYPE AND WEIGHT OF THE
WINDOW (PAR. 3.4). IT IS FORBIDDEN TO EXCEED THE LIMITS GIVEN IN TAB. 1
CONCERNING THE TECHNICAL DATA (PAR. 3.3).
THE ACTUATOR INSTALLATION MUST BE PERFORMED EXCLUSIVELY WITH
CLOSED WINDOW OR SKYLIGHT.
BEFORE PERFORMING THE INSTALLATION OF THE ACTUATOR ON HOPPER
WINDOWS, VERIFY THAT ON BOTH SIDES OF THE WINDOW TWO COMPASS
STROKE LIMIT DEVICES ARE INSTALLED IN ORDER TO AVOID THE ACCIDENTAL
FALL OF THE WINDOW.
FOR CORRECT OPERATION OF THE ACTUATOR, THE WINDOW FRAME MUST HAVE
A MINIMUM HEIGHT (DISTANCE OF THE ACTUATOR FROM THE WINDOW OPENING
HINGE) EQUAL TO THE VALUES QUOTED IN TAB. 1.
VERIFY THE DIMENSION "D": VARIABLE BETWEEN 0 TO 50 mm : FOR TOP HUNG
ASSEMBLY (FIG.6a); FOR BOTTOM HUNG ASSEMBLY (FIG.6b)
THE FITTING SURFACE FOR THE ARS RAPID COUPLING DEVICE MUST BE
PERFECTLY FLAT AND/OR SMOOTH.
CHECK THE ADEQUACY OF THE WINDOW AND THE SUITABILITY OF THE MATERIALS
OF THE WINDOW AND/OR FRAME ON WHICH THE ACTUATOR WILL BE FASTENED. AND
IT MUST ENSURE A GOOD SUPPORT OF THE ACTUATOR-WINDOW ASSEMBLY DURING
THE MOVEMENT.
INSTALLATION -5
INSTALLATION AND USE ISTRUCTIONS

16
C30S
0 15 mm÷
15 22,5 mm÷
22,5 50 mm÷ 2
0
THE FASTENING POSITION HAS TO BE VERIFIED AND EVALUATED
ACCORDING TO THE PROFILE/LENGTH OF THE WING/FRAME AND OF THE
WINDOW LIGHT.
FOR WINDOWS HAVING A “WINDOW LIGHT” LOWER THAN 500 mm, IT IS
SUGGESTED TO ADJUST THE STROKE 200 mm (SWITCH POS.I).
A
THE POSITIONS 1 - 2 - 3 - 0 ARE TO BE USED ACCORDING
TO THE OVERLAPPED PART OF THE WINDOW
D
OVERLAPPED
PART
ACTUATOR
POSITION
TYPE OF
APPLICATION
TOP HUNG
5- INSTALLATION
INSTALLATION AND USE ISTRUCTIONS
Dimensions in mm
Fig. 6a
Frame
Wing
(Standard “0” Pos.)
DIMENSION "D" VARIABLE BETWEEN 0 TO 50 mm
A
2 3
0
D
10 (+/- 1)
53
49
24
7.5
7.5
7.5
6 14
7
101

0 ÷ 15 mm 0
3
0
15 ÷ 50 mm 3
THE DIMENSION IS INCLUDED BETWEEN 96,6 mm AND 119,1 mm.
THE FASTENING POSITION HAS TO BE VERIFIED AND EVALUATED
ACCORDING TO THE PROFILE/LENGTH OF THE WING/FRAME AND OF THE
WINDOW LIGHT.
A
C
STROKE MIN. WINDOW LIGHT OPENING ANGLE MOTOR OVERALL
DIMENSIONS (B)
200 mm 500 mm 22° 39.5 mm
380 mm 900 mm 24.5° 41.5 mm
17
C30S INSTALLATION -5
THE POSITIONS 1 - 2 - 3 - 0 ARE TO BE USED ACCORDING
TO THE OVERLAPPED PART OF THE WINDOW
TOP HUNG
(see Fig.28)
INSTALLATION AND USE ISTRUCTIONS
Dimensions in mm
Fig. 6b
DIMENSION "D"
VARIABLE
BETWEEN 0 TO 50 mm
Wing
Frame
54
7,5
18,5
3
53
50
40
6±1
55
39
85
812,5
2 3
0
C
D
B
37
A
E
10,5±1

5.2- TOP HUNG WINDOWS
(Fig. 7 and Fig. 14 ÷ 21)
1) Open the package (par. 3.7) and extract the
various components;
2) Fig. 14- With a pencil draw the centre line “X” of the
window frame;
3) Fig. 15- Apply the template (POS.2) on the
window frame aligning it with the previously drawn
centre line “X”;
CA U TI O N: F O R N ON-C OP L AN A R W I ND O W
FR A M E S, I T I S N E CE S S A RY TO C U T TH E
TEMPLATE CONCERNED PART AND TO APPLY IT
ON THE WINDOW FRAME PAYING ATTENTION TO
KEEP IT IN THE SAME REFERENCE POSITION.
4) Fig. 16- With a suitable drill, create on the window frame holes having the related
diameter, given on the template;
5) Fig. 17/18- With the suitable screws tighten the bracket for window frame connection
and the quick coupling;
6) Fig. 19- Adjust the opening stroke using the switch (Ref. 1) on the right side of the
actuator according to the door opening (for tandem installations, the actuators must
have the same stroke).
CAUTION: VERIFY THAT THE SELECTED STROKE IS SOME CENTIMETRES LOWER
THAN THE STROKE EFFECTIVELY ALLOWED BY MECHANICAL LOCKS, COMPASS
LIMIT DEVICES OR WING OPENING HINDRANCES.
7) Hook the system up electrically as indicated in par. 5.4 and the wiring diagram (for
tandem installations, complete the hookup per the wiring diagram before running the
chain out). Run the chain out for at least 10 cm, then disconnect the actuator from its
power supply.
VERIFY THAT THE CHAIN ADJUSTMENT END (FIG.8 - Ref. A) IS ON THE SAME AXIS OF
THE QUICK COUPLING (FIG.8 - Ref. B). OTHERWISE, REPEAT THE OPERATIONS AND
POSITION CORRECTLY; WHEN THEY ARE NOT COAXIAL, THIS MAY DAMAGE THE
ACTUATOR AND THE WINDOW FRAME (FIG. 8).
18
C30S
5- INSTALLATION
INSTALLATION AND USE ISTRUCTIONS
Fig. 7
A A
BB
NO YES
Fig. 8

9) Fig. 20- Connect the actuator to the semi-automatic coupling inserting the chain
adjustment end first of all in the left connection point (Ref. 1) and then in the right
connection point (Ref. 2);
10) Fig. 21- Using the two supplied screws (Ref. 1) tighten the actuator to the window
frame connection bracket in the most suitable position according to the value of the
overlapped part “D” (see Fig. 6a).
FOR APPLICATION TANDEM ENSURE THAT THE ACTUATORS ARE MOUNTED ON
THE SAME HOLE OF THE ATTACHMENT BRACKET TO THE WINDOW FRAME
11) Repeat with the second actuator.
12) Power up the actuators.
13) Perform a test of complete window frame opening and closing. After the closing
phase, verify that the chain end is completely returned in its seat;
5.3- BOTTOM HUNG WINDOWS
(Fig. 9 and 22 ÷ 29)
1) Open the package (par. 3.7) and extract the
various components;
2) Fig. 22- With a pencil draw the centre line “Y” of
the window frame;
3) Fig. 23- Apply the template (Ref. 1) on the window
frame aligning it with the previously drawn centre
line “Y”;
CA UTION: FO R NON-COP LANAR WINDO W
FR AMES, IT IS N ECESS ARY TO CUT THE
TEMPLATE CONCERNED PART AND TO APPLY IT
ON THE WINDOW FRAME PAYING ATTENTION TO KEEP IT IN THE SAME
REFERENCE POSITION.
4) Fig. 24- With a suitable drill, create on the window frame holes having the related
diameter, given on the template;
5) Fig. 25/26 - With the suitable screws tighten the bracket for window frame connection
19
C30S INSTALLATION -5
INSTALLATION AND USE ISTRUCTIONS
Fig. 9

and the bottom hung opening bracket;
6) Fig. 27- Adjust the opening stroke by the switch (Ref. 1) located on the right side of
the actuator according to the opening of the wing and tighten the chain end
adjustment screw;
CAUTION: VERIFY THAT THE SELECTED STROKE IS SOME CENTIMETRES LOWER
THAN THE STROKE EFFECTIVELY ALLOWED BY MECHANICAL LOCKS, COMPASS
LIMIT DEVICES OR WING OPENING HINDRANCES.
7) Hook the system up electrically as indicated in par. 5.4 and the wiring diagram (for
tandem installations, complete the hookup per the wiring diagram before running the
chain out). Run the chain out for at least 10 cm, then disconnect the actuator from its
power supply.
8) Fig. 28- Using the two supplied screws (Ref. 1) tighten the actuator to the window
frame connection bracket in the most suitable position according to the value of the
overlapped part “D” (see Fig. 6b).
FOR APPLICATION TANDEM ENSURE THAT THE ACTUATORS ARE MOUNTED ON
THE SAME HOLE OF THE ATTACHMENT BRACKET TO THE WINDOW FRAME
9) Fig. 29- Connect the chain end to the bottom hung bracket;
10) Repeat with the second actuator.
11) Power up the actuators.
12) Perform a test of complete window frame opening and closing. After the closing
phase, verify that the chain end is completely returned in its seat;
5.4- ELECTRIC CONNECTIONS (Wiring diagram)
THE ELECTRIC CONNECTION OF THE ACTUATOR CAN BE PERFORMED ONLY BY
COMPETENT AND QUALIFIED TECHNICAL PERSONNEL SATISFYING THE
TECHNICAL AND PROFESSIONAL REQUIREMENTS FORESEEN BY THE LAW IN
FORCE IN THE COUNTRY OF INSTALLATION ISSUING TO THE CUSTOMER A
DECLARATION OF CONFORMITY FOR THE CONNECTION AND/OR THE PLANT
PERFORMED.
BEFORE PERFORMING THE ELECTRIC CONNECTION OF THE ACTUATOR, VERIFY
THE CORRECT INSTALLATION ON THE WINDOW.
THE ELECTRIC CONNECTION OF THE VERSION C30S/24V HAS TO BE CARRIED OUT
WITH A VERY LOW SAFETY VOLTAGE FEEDER PROTECTED AGAINST SHORT
CIRCUITS.
THE ELECTRIC CONNECTION OF THE VERSION C30S/24V HAS TO BE CARRIED OUT
WITH A VERY LOW SAFETY VOLTAGE FEEDER PROTECTED AGAINST SHORT
CIRCUITS.
20
C30S
5- INSTALLATION
INSTALLATION AND USE ISTRUCTIONS