TOPP C40S User manual

C40S
COD. 0P5321
VER.0.0 REV.03.16
INSTALLATION AND USE INSTRUCTIONS
CHAIN ACTUATOR FOR
WINDOW AUTOMATION
BEFORE INSTALLING AND USING THE ACTUATOR, IT IS
COMPULSORY FOR THE INSTALLER AND THE USER TO READ
AND UNDERSTAND THIS MANUAL IN ALL ITS PARTS.
THIS MANUAL IS INTEGRAL PART OF THE ACTUATOR
AND MUST BE PRESERVED FOR FUTURE REFERENCE
UNTIL DEMOLITION OF THE SAME.
original instructions
PATENTED

3
INDEX
INSTALLATION AND USE ISTRUCTIONS
1- EC DECLARATION OF INCORPORATION OF PARTLY COMPLETED
MACHINERY
........................................................................................................................page 04
2- GENERAL REMARKS
2.1- General instructions..........................................................................................page 05
2.2- Installer and user ..............................................................................................page 05
2.3- Technical assistance.........................................................................................page 05
2.4- Reserved rights ................................................................................................page 06
2.5- Description of personnel...................................................................................page 06
3- TECHNICAL DESCRIPTION
3.1- Rating plate and "CE" marking.........................................................................page 07
3.2- Denomination of the components and dimensions ..........................................page 08
3.3- Technical data...................................................................................................page 09
3.4- Formulas for the calculation of thrust force or tractive force ............................page 10
3.5- Destination of use.............................................................................................page 10
3.6- Use Limits.........................................................................................................page 11
3.7- Standard Package ............................................................................................page 11
4- SAFETY
4.1- General instructions .........................................................................................page 13
4.2- Safety Devices .................................................................................................page 13
4.2.1- Protections against electric hazard ...............................................................page 13
4.3- Safety plates.....................................................................................................page 14
4.4- Residual risks ...................................................................................................page 14
5- INSTALLATION
5.1- General instructions .........................................................................................page 15
5.2- Top hung windows ............................................................................................page 18
5.3- Bottom hung windows ......................................................................................page 19
5.4- Electrical Connections......................................................................................page 21
5.5- Control devices.................................................................................................page 22
5.6- Emergency procedures ....................................................................................page 23
6- USE AND OPERATION
6.1- Use of the actuator...........................................................................................page 24
6.2- Smart Reset System (SAI)..............................................................................page 25
7- MAINTENANCE
7.1- General instructions .........................................................................................page 26
8- DEMOLITION
8.1- General instructions .........................................................................................page 26
9- SPARE PARTS AND ACCESSORIES UPON REQUEST
9.1- General instructions .........................................................................................page 26
FIGURES
........................................................................................................................page 27
C40S

4
C40S
INSTALLATION AND USE ISTRUCTIONS
1- EC DECLARATION OF INCORPORATION OF PARTLY COMPLETED MACHINERY
The undersigned, in the name of and behalf of the following company
Topp S.r.l.
Via Galvani, 59
36066 Sandrigo (VI)
Italia
herewith declares
that the person authorised to compile the technical file is
Name: Bettiati Roberto - Topp S.r.l.
Address: via Galvani,59 36066 Sandrigo (VI)
and
that to the partly completed machinery
CHAIN ACTUATOR FOR WINDOW AUTOMATION
Type: C40S
Model(s): C40S/230V - C40S/24V
Serial number and year of construction: from no.1603TB01112 to no. 16120PF1999
the following essential requirements of the following EC directive (including all applicable
amendments)
2006/42/EC Machinery Directive (Italian adoption DLgs 27 jan. 2010, n.17)
have been applied and fulfilled:
Enclosure I: 1.5.1; 1.5.2; 1.5.10; 1.5.11
and that the relevant technical documentation is compiled in accordance with part B of
Annex VII of the above mentioned Machinery Directive.
The above identified partly completed machinery is also in conformity with the all the
relevant provisions of the following EC directives (including all applicable amendments)
2014/30/EU EMC Directive
2011/65/EU ROHS II Directive
The following harmonised standards have been applied:
EN 55014-1 EN 55014-2 EN 61000-3-2
EN 61000-3-3 EN 61000-6-2 EN 61000-6-3
EN 62233 EN 50581
EN 60335-1 Applicable parts of EN 60335-2-103
The undersigned also undertakes the obligation, in response to a duly reasoned request by the
national market surveillance authorities, to transmit to the a.m. authorities, in electronic or
paper format, the relevant technical documentation on the partly completed machinery.
The above identified partly completed machinery must not be put into service until the final
machinery into which it is to be incorporated has been declared in conformity with the
provisions of the above mentioned Machinery Directive.
This declaration of conformity is issued under the sole responsibility of the manufacturer.
Date: Sandrigo, 01/03/2016 Signature: Matteo Cavalcante
Administrator .......................................................
ORIGINAL

5
C40S GENERAL REMARKS -2
2.1- GENERAL INSTRUCTIONS
BEFORE INSTALLING AND USING THE ACTUATOR, IT IS COMPULSORY THAT THE
INSTALLER AND THE USER CAREFULLY READ AND UNDERSTAND THIS MANUAL IN
ALL ITS PARTS.
THIS MANUAL IS INTEGRAL PART OF THE ACTUATOR AND MUST COMPULSORILY BE
PRESERVED FOR FUTURE REFERENCE.
THE MANUFACTURER HAS NO LIABILITY FOR ANY EVENTUAL DAMAGE TO PERSONS,
ANIMALS AND THINGS DUE TO THE INOBSERVANCE OF THE PRESCRIPTIONS
DESCRIBED IN THIS MANUAL.
IN ORDER FOR THE AUTOMATION UNIT TO OPERATE CORRECTLY, WE RECOMMEND
CARRYING OUT PERIODICAL MAINTENANCE ON IT, AS INDICATED IN PAR. 7.1 OF THIS
MANUAL.
THE WARRANTY ON THE ACTUATOR WILL NOT BE HONORED IF PRODUCT IS NOT
INSTALLED AND USED ACCORDING TO THE INSTRUCTIONS PROVIDED AND THE
REGULATIONS SHOWN IN THIS INSTRUCTION MANUAL AND IF IT IS USED WITH NON-
GENUINE PARTS, ACCESSORIES, SPARE PARTS AND/OR CONTROL/FEEDING UNITS.
2.2- INSTALLER AND USER
THE ACTUATOR INSTALLATION CAN BE PERFORMED EXCLUSIVELY BY COMPETENT
AND QUALIFIED TECHNICAL PERSONNEL SATISFYING THE PROFESSIONAL AND
TECHNICAL REQUIREMENTS FORESEEN BY THE LAWS IN FORCE IN THE COUNTRY OF
INSTALLATION.
THE INSTALLATION TECHNICIAN SHALL ACCEPT FULL RESPONSIBILITY FOR ANY
INSTALLATION ERRORS AND FOR ANY FAILURE TO ADHERE TO THE INSTRUCTIONS
PROVIDED IN THIS MANUAL. THE INSTALLATION TECHNICIAN SHALL THEREFORE BE
EXCLUSIVELY LIABLE FOR ANY DAMAGES CAUSED TO USERS AND/OR THIRD
PARTIES THAT MAY ARISE AS A RESULT OF INCORRECT INSTALLATION.
THE ACTUATOR CAN BE USED EXCLUSIVELY BY A USER ACTING IN COMPLIANCE WITH
THE INSTRUCTIONS CONTAINED IN THIS MANUAL AND/OR IN THE MANUAL OF THE
ACTUATOR CONTROL DEVICE (e.g.: CONTROL UNIT).
2.3- TECHNICAL ASSISTANCE
Contact the installation technician or retailer for assistance.
INSTALLATION AND USE ISTRUCTIONS

6
C40S
INSTALLATION AND USE ISTRUCTIONS
2.4- RESERVED RIGHTS
The reserved rights on this manual "Installation and use instructions" remain property of
the Manufacturer.
Each information herein contained (text, drawings, diagrams, etc.) is reserved.
None part of this manual can be reproduced and disclosed (totally or partially) by any
reproduction means (photocopies, microfilms or other) without written authorization of
the Manufacturer.
2.5- DESCRIPTION OF PERSONNEL
USERS MUST NEVER PERFORM OPERATIONS RESERVED FOR MAINTENANCE
PEOPLE OR SPECIALISED TECHNICIANS. THE MANUFACTURER DECLINES ALL
LIABILITY FOR DAMAGE DERIVING FROM FAILURE TO OBSERVE THE ABOVE
REQUIREMENTS.
Specialised electrician:
A specialised electrician must be able to install the actuator, start it and operate it both
in normal conditions and in the maintenance mode; he/she is qualified to perform all
electrical and mechanical adjustment and maintenance operations. He/she is allowed
to work on live electrical cabinets and junction boxes.
User:
specialised person capable of operating the actuator under normal conditions by using
the relative controls. He/she must also be able to operate with the actuator under
“maintenance” in order to perform simple routine maintenance operations (cleaning),
and start or reset the actuator following an unscheduled stop.
2- GENERAL REMARKS

3.1- RATING PLATE AND "CE" MARKING
The "CE" marking certifies the compliance of the machine with the essential safety and
health requirements foreseen by the product European Directives.
The rating plate is an adhesive plate in polyester, silk-screen printed in black, having the
following size: L= 36 mm - H= 50 mm.
It is applied externally on the actuator. The plate bears in readable and indelible way the
following data:
• logo and address of the manufacturer
• type and model
• voltage and intensity of power supply (V - A)
• absorbed electric power P (W)
• thrust and tractive force F (N)
• type of service S (min)
2
• idle translation speed (mm/s)
• protection degree (IP)
• "CE" marking
• symbol of WEEE Directive 2002/96/CE
• symbol of double insulation (only for mod. C40S/230V)
• serial number
7
C40S TECHNICAL DESCRIPTION -3
INSTALLATION AND USE ISTRUCTIONS

51
8.4
11
Ø 4.2
11
15.5
27.8
15
42
2
1
16
86
15
132.9
126.4
6.5
4
3.2- DENOMINATION OF THE COMPONENTS AND DIMENSIONS
Dimensions in mm LEGEND:
1) Quick coupling
2) Slot side indicator
3) Chain end
4) Bracket for bottom hung opening
5) Connection bracket to the frame
6) Power supply cable
7) Actuator
8) Opening stroke adjustment
selector
8
C40S
3- TECHNICAL DESCRIPTION
INSTALLATION AND USE ISTRUCTIONS
Fig. 1
45
50
69.2
59.7
5
6
7
3
116.7
387.6
95
335 345
355,5
8
10,5 20,5
10

Maximum applicable thrust load
Maximum applicable tractive load
Idle translation speed
Duration of the idle stroke
(1)
Adjustable strokes on outlet
Minimum height
(2)
of the window frame
Return end of stroke for the absorption in the last 100 mm
Tab. 1
Power supply voltage
Absorbed current
Absorbed power with load
Type of service (3) S2
Operating temperature
Protection degree of electric devices
Adjustment of the window frame connection
Chain position control
Actuator weight with brackets
Gross weight
(1) Tolerance on the tripping precision of the limit switch at output: +/- 10 mm
(2) Distance of the actuator from the window opening hinge valid only with max. stroke 380 mm
(3) Service of limited duration according to EN 60034
3.3- TECHNICAL DATA
Tab. 1 contains the technical data characterising the actuators.
100 - 150 - 200 - 250 - 300 - 400 - 500 mm
230 V ~ 50 Hz
0,18 A
24 W
400 N
7,7 mm/s
65 s
1 A
24 W
7,7 mm/s
65 s
5 min 5 min
H= 300 ¸ 500 mm (v. Fig. 6a)
H= 300 ¸ 1000 mm (v. Fig. 6b)
-5°C +50°C
IP 55
Unnecessary
Yes
1,9 kg
2,2 kg
Yes ( )see wiring diagram
C40S/230V C40S/24V
Top hung
Bottom
hung
Parallel connection of more than one actuator
9
C40S TECHNICAL DESCRIPTION -3
INSTALLATION AND USE ISTRUCTIONS
Class II Class III
Protection against electric shocks
24 V
Synchronization of two actuators on the
same window
Yes
Max. overlapped part “D”
50mm
450
400
350
300
250
200
150
100
50
100 200 300 400 500
F [N]
Stroke [mm]
Thrust load actuator [N]
C40S / 230V
C40S / 24V
300 N
Maximum Width
of the window
Single actuator
Two actuators
<1800mm
>1800mm

3.5- DESTINATION OF USE
THE ACTUATOR HAS BEEN DESIGNED AND MANUFACTURED TO PERFORM
AUTOMATICALLY, BY MEANS OF A CONTROL DEVICE, THE OPENING AND CLOSING OF
TOP HUNG WINDOWS, BOTTOM HUNG WINDOWS, PIVOT WINDOWS, AND SKYLIGHTS.
The C40S Chain actuator is equipped with the latest TOPP system for the coordinated
synchronization of the chain movement. The electronic speed control is fully automatic and
requires no external control unit; just connect the yellow/white/blue cables as per wiring diagram at
the back of the manual to achieve the synchronized mode. The Smart Reset System (SAI) has
also been included which adjusts the closure of the window in an optimum manner.
The C40S chain actuator is mounted when you need two or more attachment points because the
window is particularly heavy or wide and only one actuator would not allow perfect closure of the
window. It should be remembered that the force exerted by the actuators individually is the same
as a similar C40 actuator; for example, by mounting two actuators the force applied to the window
is, therefore, doubled. The window is moved in a uniform, synchronized and coordinated manner
with no interruptions and/or speed changes in the actuators' operation. In the event of any failure of
one of the actuators due to a mechanical or electrical fault, the others also stop operating,
guaranteeing that the window remains intact.
3.4- FORMULAS FOR THE CALCULATION OF THRUST AND TRACTIVE
FORCE
Top hung windows (A) or
bottom hung windows (B)
F= Force necessary for opening or
(N)
closing
P= Weight of the window
(N)
(only movable part)
C= Window opening stroke
(mm)
H= Window height
(mm)
F = (0,54 x P) x ( )
C
H
P
F
H
C
B
P
F
H
C
A
F
P
Horizontal domes or skylights
F= Force necessary for opening or
(N)
closing
P= Weight of the skylight or dome
(N)
(Only movable part)
F = 0,54 x P
10
C40S
3- TECHNICAL DESCRIPTION
INSTALLATION AND USE ISTRUCTIONS
Fig. 2
Fig. 3

3.6- USE LIMITS
The actuator has been designed and manufactured exclusively for the destination of
use given in par. 3.5, therefore, any other type of use is strictly forbidden in order to
assure in any moment the safety of the installer and of the user, as well as the efficiency
of the actuator itself.
Check carefully all environmental conditions (temperature, humidity, wind, snow,
potential chemical agents, etc.) and installation settings (misaligned fitting of brackets
and attachment to the frame, frictions produced by hinges or gaskets, use of self-
balancing window stays, etc.) it is recommended that they not exceed the actuator
performances shown in the technical table.
IT IS STRICTLY FORBIDDEN TO USE THE ACTUATOR FOR IMPROPER USES OTHER
THAN THE ONE FORESEEN BY THE MANUFACTURER (SEE PAR. 3.5).
IT IS STRICTLY FORBIDDEN TO INSTALL THE ACTUATOR ON THE EXTERNAL SIDE OF
THE WINDOW FRAME SUBJECT TO ATMOSPHERIC AGENTS (RAIN, SNOW, ETC.).
THE USE OF THE ACTUATOR IN ENVIRONMENTS WITH POTENTIALLY EXPLOSIVE
ATMOSPHERE IS STRICTLY FORBIDDEN.
IT IS COMPULSORY TO KEEP THE PACKAGE AND THE ACTUATOR OUT OF REACH OF
CHILDREN.
3.7- PACKAGESTANDARD
Each standard package of the product (cardboard box) contains (Fig. 4):
• No.1 Actuator equipped with power supply cable;
• No.1 Window frame connection bracket (Ref. A);
• No.1 Bracket for bottom hung opening (Ref. B);
• No.1 Small part package (quick coupling, No. 2 bracket fastening lateral screws, No. 7
screws AF Ø 4.2 x 19 mm fastening the bracket on the window frame and
tightening the quick coupling and a tool for quick release) (Ref. C);
• No. 1 Adhesive drilling template (Ref. D);
• No.1 Installation and use instructions (Ref. E);
• No.1 Safety Plate (Fig. 5).
MAKE SURE THAT THE ABOVE DESCRIBED COMPONENTS ARE CONTAINED IN THE
PACKAGE, AS WELL AS THAT THE ACTUATOR HAS NOT BEEN DAMAGED DURING
TRANSPORT.
SHOULD ANY ANOMALY BE DETECTED, IT IS FORBIDDEN TO INSTALL THE ACTUATOR,
AND IT IS COMPULSORY TO REQUIRE TECHNICAL ASSISTANCE FROM YOUR DEALER
OR THE MANUFACTURER.
THE PACKAGING (PAPER, PLASTIC, ETC.) HAS TO BE DISPOSED ACCORDING TO THE
LAWS IN FORCE.
EX
11
C40S TECHNICAL DESCRIPTION -3
INSTALLATION AND USE ISTRUCTIONS

A
12
C40S
3- TECHNICAL DESCRIPTION
INSTALLATION AND USE ISTRUCTIONS
Fig. 4
C40S
COD. 0P5251
REV.10.15
INSTALLATION AND USE INSTRUCTIONS
CHAIN ACTUATOR FOR
WINDOW AUTOMATION
PATENTED
BEFORE INSTALLING AND USING THE ACTUATOR, IT IS
COMPULSORY FOR THE INSTALLER AND THE USER TO READ
AND UNDERSTAND THIS MANUAL IN ALL ITS PARTS.
THIS MANUAL IS INTEGRAL PART OF THE ACTUATOR
AND MUST BE PRESERVED FOR FUTURE REFERENCE
UNTIL DEMOLITION OF THE SAME.
E
D
BC

4.1- GENERAL INSTRUCTIONS
OPERATORS MUST BE INFORMED OF ACCIDENT RISKS, SAFETY DEVICES AND THE
GENERAL ACCIDENT PREVENTION REGULATIONS ESTABLISHED BY INTERNATIONAL
DIRECTIVES AND BY THE LAW IN FORCE IN THE COUNTRY OF USE.
ALL OPERATORS MUST STRICTLY COMPLY WITH THE ACCIDENT PREVENTION
REGULATIONS IN FORCE IN THE COUNTRY OF USE.
DO NOT REMOVE OR ALTER THE PLATES PLACED ON THE ACTUATOR BY THE
MANUFACTURER.
IF THE WINDOW FRAME IS ACCESSIBLE FROM OR INSTALLED AT A HEIGHT OF LESS
THAN 2.5 m FROM THE GROUND, AND IF IT CAN BE COMMANDED BY AN UNTRAINED
USER OR WITH A REMOTE CONTROL DEVICE, FIT AN EMERGENCY STOP SYSTEM
WHICH AUTOMATICALLY CUTS IN TO PREVENT THE RISK OF CRUSHING OR
DRAGGING PARTS OF THE BODY INSERTED BETWEEN THE MOVING AND FIXED PARTS
OF THE WINDOW FRAME.
ANY TAMPERING WITH OR UNAUTHORISED REPLACEMENT OF ONE OR MORE PARTS
OR COMPONENTS OF THE ACTUATOR, OR THE USE OF UNORIGINAL ACCESSORIES
AND CONSUMABLES, MAY INCREASE THE RISK OF ACCIDENT AND THUS RELIEVES
THE MANUFACTURER OF ALL CIVIL AND PENAL LIABILITY
EXTRAORDINARY AND ROUTINE MAINTENANCE OPERATIONS INVOLVING THE TOTAL
OR PARTIAL DISMOUNTING OF THE ACTUATOR MAY ONLY BE PERFORMED AFTER
DISCONNECTING IT FROM THE POWER SUPPLY.
THIS APPLIANCE MAY NOT BE USED BY PERSONS (CHILDREN INCLUDED) WITH
REDUCED PHYSICAL, SENSORIAL OR MENTAL CAPACITIES, OR INEXPERT PEOPLE,
UNLESS THEY ARE SUPERVISED AND TAUGHT HOW TO USE IT BY A PERSON
RESPONSIBLE FOR THEIR SAFETY. CHILDREN MUST BE CONTROLLED TO MAKE
SURE THEY DO NOT PLAY WITH THE APPLIANCE.
4.2- SAFETY DEVICES
4.2.1- PROTECTION AGAINST ELECTRIC HAZARD
The actuator is protected against electric hazard due to direct and indirect contacts.
The protection measures against direct contacts aim at protecting people against
hazards due to contact with active parts, usually live parts; while the protection
measures against indirect contacts aim at protecting people against hazards due to
conducing part, which are usually insulated, but could become live in case of failure
(insulation failure).
The adopted protection measures are the following:
1) Insulation of live parts by means of a plastic material body;
2) Enclosure with suitable protection degree;
3) Only for Mod. C40S/230 V equipped with double insulation: Protection of passive
13
C40S
INSTALLATION AND USE ISTRUCTIONS
SAFETY -4

14
C40S
4- SAFETY
INSTALLATION AND USE ISTRUCTIONS
type given by the use of components with double insulation, also called components of
class II or with equivalent insulation. (It is forbidden to connect the actuators equipped
with double insulation to the earth plant.
4.3- SAFETY PLATES
IT IS FORBIDDEN TO REMOVE, MOVE, SPOIL OR IN ANYWAY REDUCE THE VISIBILITY
OF THE SAFETY PLATES. FAILURE TO OBSERVE THE ABOVE MAY CAUSE SERIOUS
HARM TO PEOPLE AND DAMAGE TO PROPERTY. THE MANUFACTURER DECLINES ALL
LIABILITY FOR ANY DAMAGE CAUSED BY THE FAILURE TO OBSERVE THE ABOVE
REQUIREMENT.
Fig. 5 illustrates the safety plate: this must applied directly to the outside of the actuator
or near it and always in a position where it can be seen by the installer and/or operator.
4.4- RESIDUAL RISKS
The installer and the user are herewith informed that after the actuator has been
installed on the window, the actuator drive can accidentally generate the following
residual risk:
Residual risk: Hazard of squashing or dragging of body parts inserted between the
movable and the fix part of the window frame.
Exposure frequency: Accidental and when the installer or the user decides to perform
a wrong voluntary action.
Severity of the damage: Light lesions (usually reversible).
Adopted measures: Before enabling the device, it is compulsory to verify that near the
window there are not persons, animals or things whose safety may be accidentally
jeopardized. During actuator operation, it is compulsory to be in a safe control position
assuring visual control on the window movement (see par.6.1).
Fig. 5
MACCHINA AD AVVIAMENTO AUTOMATICO
AUTOMATIC MACHINE
PRIMA DI INSTALLARE E UTILIZZARE L'ATTUATORE È OBBLIGATORIO CHE L'INSTALLATORE E L'UTILIZZATORE
LEGGANO E COMPRENDANO IN TUTTE LE SUE PARTI IL MANUALE
THE INSTALLER AND USER MUST READ AND UNDERSTAND ALL PARTS OF THIS MANUAL BEFORE INSTALLING
AND USING THE ACTUATOR.
PERICOLO ATTENZIONE ALLE MANI
BEWARE OF YOUR HANDS
ATTENZIONE MACCHINA AD AVVIAMENTO AUTOMATICO CON COMANDO A DISTANZA
ATTENTION! AUTOMATIC MACHINE WITH REMOTE CONTROL DEVICE
IT
EN

15
C40S
5.1- GENERAL INSTRUCTIONS
THE ACTUATOR INSTALLATION CAN BE PERFORMED EXCLUSIVELY BY COMPETENT
AND QUALIFIED TECHNICAL PERSONNEL SATISFYING THE PROFESSIONAL AND
TECHNICAL REQUIREMENTS FORESEEN BY THE LAWS IN FORCE IN THE COUNTRY OF
INSTALLATION.
THE ACTUATOR PERFORMANCE MUST BE SUFFICIENT TO ASSURE THE CORRECT
MOVEMENT OF THE WINDOW. IT IS COMPULSORY TO VERIFY THE THRUST OR
TRACTIVE FORCE ACCORDING TO THE TYPE AND WEIGHT OF THE WINDOW (PAR. 3.4).
IT IS FORBIDDEN TO EXCEED THE LIMITS GIVEN IN TAB. 1 CONCERNING THE
TECHNICAL DATA (PAR. 3.3).
THE ACTUATOR INSTALLATION MUST BE PERFORMED EXCLUSIVELY WITH CLOSED
WINDOW OR SKYLIGHT.
BEFORE PERFORMING THE INSTALLATION OF THE ACTUATOR ON HOPPER
WINDOWS, VERIFY THAT ON BOTH SIDES OF THE WINDOW TWO COMPASS STROKE
LIMIT DEVICES ARE INSTALLED IN ORDER TO AVOID THE ACCIDENTAL FALL OF THE
WINDOW.
FOR CORRECT OPERATION OF THE ACTUATOR, THE WINDOW FRAME MUST HAVE A
MINIMUM HEIGHT AS QUOTED IN THE TABLE OF FIG. 6a FOR THE TOP HUNG
ASSEMBLY AND IN THE TABLE OF FIG. 6b FOR THE BOTTOM HUNG ASSEMBLY.
VERIFY THAT THE POSITIONS OF THE LABELS LOCATED ON THE QUICK COUPLING
CORRESPOND TO THE LABELS ON THE ACTUATOR: RED LABEL WITH LETTER "A"
FOR THE TOP HUNG ASSEMBLY, GREEN LABEL WITH LETTER "B" FOR VERTICAL
ASSEMBLY.
VERIFY THAT THE DISTANCE "D" BETWEEN THE FRAME OF THE WINDOW FRAME (ON
WHICH THE FIXING OF THE ACTUATOR IS FORESEEN) AND THE WING OF THE WINDOW
FRAME (ON WHICH THE FASTENING OF THE BRACKET IS FORESEEN) IS INCLUDED
BETWEEN 0 AND 50 mm BOTH FOR THE TOP HUNG ASSEMBLY (SEE FIG 6a) AND FOR
THE BOTTOM HUNG ASSEMBLY (SEE FIG 6b).
THE FITTING SURFACE FOR THE ARS RAPID COUPLING DEVICE MUST BE PERFECTLY
FLAT AND/OR SMOOTH.
INSTALLATION -5
INSTALLATION AND USE ISTRUCTIONS

TOP HUNG OPENING
POS. STROKE (mm) WINDOW MIN
HEIGHT (mm)
1
2
3
4
5
6
7
100
150
200
250
300
400
500
300
350
450
500
THE FASTENING POSITION HAS TO BE VERIFIED AND EVALUATED ACCORDING
TO THE PROFILE/LENGTH OF THE WING/FRAME AND OF THE WINDOW LIGHT.
A
DISTANCE "D" VARIABLE BETWEEN 0 TO 50 mm
16
C40S
5- INSTALLATION
INSTALLATION AND USE ISTRUCTIONS
Fig. 6a
A
FRAME
WING
28,5
18,5
50
69,2
117,2
9
6
50
D
10
OVERLAPPED PART “D”
MUST BE LOWER 50mm

BOTTOM HUNG OPENING
1
2
3
4
5
6
7
100
150
200
250
300
400
500
300
500
400
900
1000
POS. STROKE (mm) WINDOW MIN
HEIGHT (mm)
THE FASTENING POSITION HAS TO BE VERIFIED AND EVALUATED ACCORDING
TO THE PROFILE/LENGTH OF THE WING/FRAME AND OF THE WINDOW LIGHT.
A
17
C40S INSTALLATION -5
INSTALLATION AND USE ISTRUCTIONS
Fig. 6b
79.5
D
A
33
6
15.5
WING
FRAME
128.4
69.2
50
10,5 1010,5
21,5
14
DISTANCE "D" VARIABLE BETWEEN 0 TO 50 mm
OVERLAPPED PART “D”
MUST BE LOWER 50mm

18
C40S
5- INSTALLATION
INSTALLATION AND USE ISTRUCTIONS
5.2- TOP HUNG WINDOWS
(Fig. 7 and Fig. 13 ÷ 20)
1) Open the package (par. 3.7) and extract the
various components;
2) Fig. 13- With a pencil draw the centre line “X” of the
window frame;
3) Fig. 14- Apply the template (POS.2) on the window
frame aligning it with the previously drawn centre
line “X”;
CAUTION: FOR NON-COPLANAR WINDOW FRAMES,
IT IS NECESSARY TO CUT THE TEMPLATE
CONCERNED PART AND TO APPLY IT ON THE
WINDOW FRAME PAYING ATTENTION TO KEEP IT IN
THE SAME REFERENCE POSITION.
4) Fig. 15- With a suitable drill, create on the window frame holes having the related
diameter, given on the template;
5) Fig. 16/17- With the suitable screws tighten the bracket for window frame connection
and the quick coupling;
6) Fig. 18- With an Allen wrench, adjust the opening stroke by means of a proper
selector (Ref. 1) (for tandem installations, the actuators must have the same stroke).
CAUTION: VERIFY THAT THE SELECTED STROKE IS SOME CENTIMETRES LOWER THAN
THE STROKE EFFECTIVELY ALLOWED BY MECHANICAL LOCKS, COMPASS LIMIT
DEVICES OR WING OPENING HINDRANCES.
7) Hook the system up electrically as indicated in par. 5.4 and the wiring diagram (for
tandem installations, complete the hookup per the wiring diagram before running the
chain out). Run the chain out for at least 10 cm, then disconnect the actuator from its
power supply.
VERIFY THAT THE CHAIN ADJUSTMENT END (FIG.8 - Ref. A) IS ON THE SAME AXIS OF
THE QUICK COUPLING (FIG.8 - Ref. B). OTHERWISE, REPEAT THE OPERATIONS AND
POSITION CORRECTLY; WHEN THEY ARE NOT COAXIAL, THIS MAY DAMAGE THE
ACTUATOR AND THE WINDOW FRAME (FIG. 8).
Fig. 7
YES
A A
BB
NO
Fig. 8

19
C40S INSTALLATION -5
INSTALLATION AND USE ISTRUCTIONS
8) Fig. 19- Connect the actuator to the semi-automatic coupling inserting the chain
adjustment end first of all in the left connection point (Ref. 1) and then in the right
connection point (Ref. 2);
9) Fig. 20- Using the two supplied screws (Ref. 1) tighten the actuator to the window
frame connection bracket in the most suitable position according to the value of the
overlapped part “D” (see Fig. 6a).
FOR APPLICATION TANDEM ENSURE THAT THE ACTUATORS ARE MOUNTED ON THE
SAME HOLE OF THE ATTACHMENT BRACKET TO THE WINDOW FRAME
10) Repeat with the second actuator.
11) Power up the actuators.
12) Perform a test of complete window frame opening and closing. After the closing
phase, verify that the chain end is completely returned in its seat;
5.3- BOTTOM HUNG WINDOWS
(Fig. 10 and 21 ÷ 28)
1) Open the package (par. 3.7) and extract the
various components;
2) Fig. 21- With a pencil draw the centre line “Y” of
the window frame;
3) Fig. 22- Apply the template (Ref. 1) on the window
frame aligning it with the previously drawn centre
line “Y”;
CAUTION: FOR NON-COPLANAR WINDOW FRAMES,
IT IS NECESSARY TO CUT THE TEMPLATE
CONCERNED PART AND TO APPLY IT ON THE
WINDOW FRAME PAYING ATTENTION TO KEEP IT IN THE SAME REFERENCE POSITION.
4) Fig. 23- With a suitable drill, create on the window frame holes having the related
diameter, given on the template;
5) Fig. 24/25 - With the suitable screws tighten the bracket for window frame connection
and the bottom hung opening bracket;
Fig. 10

20
C40S
5- INSTALLATION
INSTALLATION AND USE ISTRUCTIONS
6) Fig. 26- Adjust the opening stroke by the switch (Ref. 1) located on the right side of
the actuator according to the opening of the wing and tighten the chain end
adjustment screw;
CAUTION: VERIFY THAT THE SELECTED STROKE IS SOME CENTIMETRES LOWER THAN
THE STROKE EFFECTIVELY ALLOWED BY MECHANICAL LOCKS, COMPASS LIMIT
DEVICES OR WING OPENING HINDRANCES.
7) Hook the system up electrically as indicated in par. 5.4 and the wiring diagram (for
tandem installations, complete the hookup per the wiring diagram before running the
chain out). Run the chain out for at least 10 cm, then disconnect the actuator from its
power supply.
8) Fig. 27- Connect the chain end to the bottom hung bracket;
9) Fig. 28- Using the two supplied screws (Ref. 1) tighten the actuator to the window
frame connection bracket in the most suitable position according to the value of the
overlapped part “D” (see Fig. 6b).
FOR APPLICATION TANDEM ENSURE THAT THE ACTUATORS ARE MOUNTED ON THE
SAME HOLE OF THE ATTACHMENT BRACKET TO THE WINDOW FRAME
10) Repeat with the second actuator.
11) Power up the actuators.
12) Perform a test of complete window frame opening and closing. After the closing
phase, verify that the chain end is completely returned in its seat;