Toro 08719 User manual

Form No. 3465-223 Rev A
Finish Brush Kit
Flex
™
T ooth Rake for Sand Pro
®
T raction Units
Model No. 08719
Operator's Manual
Introduction
Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. Y ou are responsible for
operating the product properly and safely .
Y ou may contact T oro directly at www .T oro.com for
product and accessory information, help nding a
dealer , or to register your product.
Whenever you need service, genuine T oro parts, or
additional information, contact an Authorized Service
Dealer or T oro Customer Service and have the model
number of your product ready .
This manual identies potential hazards and has
safety messages identied by the safety alert symbol
(Figure 1 ), which signals a hazard that may cause
serious injury or death if you do not follow the
recommended precautions.
g000502
Figure 1
1. Safety alert symbol
This manual uses 2 words to highlight information.
Important calls attention to special mechanical
information and Note emphasizes general information
worthy of special attention.
W ARNING
CALIFORNIA
Proposition 65 W arning
Use of this product may cause exposure
to chemicals known to the State of
California to cause cancer , birth defects,
or other reproductive harm.
Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Description
Qty .
Use
W eight (Sand Pro 2040Z Only)
2
Install the weights (Sand Pro 2040Z Only).
Brush assembly (left-hand)
1
Brush assembly (right-hand)
1
Screw (1/4 x 1-1/4 inch)
4
Locknut (1/4 inch)
4
Install the side brushes.
Brush assembly (center)
1
Screw (1/4 x 7/8 inch)
2
Locknut (1/4 inch)
2
Install the center brush.
© 2023—The T oro® Company
81 1 1 L yndale A venue South
Bloomington, MN 55420
Register at www .T oro.com.
Original Instructions (EN)
Printed in the USA
All Rights Reserved
*3465-223*

Installing the W eights
Sand Pro 2040Z Only
Before installing the nish brush kit, ensure that there
are 6 weights installed on the front of the machine;
refer to Installing and Removing the W eights ( page 4 ) .
Installing the Side Brushes
1. Remove the screw and the locknut on the end
of 1 of the rake side assemblies as shown in
Figure 2 .
g024613
Figure 2
1. Screws (existing) 2. Locknuts (existing)
2. Remove the screw and the locknut located in
the 5th position from the end of the rake side
assembly as shown in Figure 2 .
3. Align the 2 mounting holes in the brush assembly
with the 2 mounting holes in the rake side
assembly ( Figure 3 ).
g024614
Figure 3
1. Screws (1/4 x 1-1/4 inch)
3. Brush assembly
2. Locknuts (1/4 inch)
4. Secure the brush assembly to the rake with 2
screws (1/4 x 1-1/4 inch) and 2 locknuts (1/4
inch); refer to Figure 3 .
5. Repeat the procedure for the other side of the
rake.
Note: The side brushes are not symmetrical.
Ensure that the center brush overlaps the side
brushes; if it does not, switch the side brushes
(Figure 4 ).
g024630
Figure 4
2

Installing the Center Brush
1. Remove the 2 screws and the 2 locknuts near
the center of the rake center assembly as shown
in Figure 5 .
g024615
Figure 5
1. Screws (existing) 2. Locknuts (existing)
2. Align the 2 mounting holes in the brush assembly
with the 2 mounting holes in the rake center
assembly Figure 6 .
g024616
Figure 6
1. Screws (1/4 x 7/8 inch)
3. Brush assembly
2. Locknuts (1/4 inch)
3. Secure the brush assembly to the rake with 2
screws (1/4 x 7/8 inch) and 2 locknuts (1/4 inch);
refer to Figure 6 .
Product Overview
g024629
Figure 7
1. W eights (2 included—For Sand Pro 2040Z Only)
2. Right-hand brush assembly
3. Center brush assembly
4. Left-hand brush assembly
g024673
Figure 8
Installed brush kit
3

Operation
Installing and Removing
the W eights
Sand Pro 2040Z Only
Always ensure that your machine has the appropriate
number of weights.
Refer to the following table for how many weights are
required on the front of the machine:
Attachment
Number of weights required
Flex tooth rake 4
Flex tooth rake with nish
brush
6
Nail drag 6
Nail drag with nish drag mat
8
Note: Sand Pro machines other than the 2040Z do
not require the additional weights included in this kit.
1. Remove the 2 bolts and 2 nuts securing the
existing weights on the front of the machine
(Figure 9 ).
Note: If the machine is equipped with the light
kit, remove the nut and the bolt securing the
front light to the machine. Retain all of the parts;
refer to the Light Kit Installation Instructions .
g023729
Figure 9
2. Add or remove weights as necessary .
3. Secure the weights with the 2 bolts and the 2
nuts.
Note: If the machine is equipped with the light
kit, install the front light by inserting the bolt
through the weights and securing it with the nut;
refer to the Light Kit Installation Instructions .
Adjusting the Lift-in-turn
System
Sand Pro 2040Z Only
Ensure that the tires are inated to 48 kPa (7 psi), and
ensure that the lift-in-turn height is adequate; refer to
the rake Operator ’ s Manual .
4

Notes:

Notes:

Declaration of Incorporation
The T oro Company , 81 1 1 L yndale A ve. South, Bloomington, MN, USA declares that the following unit(s)
conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain
T oro models as indicated on the relevant Declarations of Conformity .
Model No.
Serial No.
Product Description Invoice Description
General Description
Directive
08719
—
Finish Brush Kit
SP2040Z FINISHING
BRUSH KIT
Broom Finishing Kit
2006/42/EC
Relevant technical documentation has been compiled as required per Part B of Annex VII of 2006/42/EC.
W e will undertake to transmit, in response to requests by national authorities, relevant information on this partly
completed machinery . The method of transmission shall be electronic transmittal.
This machinery shall not be put into service until incorporated into approved T oro models as indicated on the
associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in
conformity with all relevant Directives.
Certied:
Authorized Representative:
Marcel Dutrieux
Manager European Product Integrity
T oro Europe NV
Nijverheidsstraat 5
2260 Oevel
Belgium
T om Langworthy
Engineering Director
81 1 1 L yndale A ve. South
Bloomington, MN 55420, USA
September 17, 2023

UK Declaration of Incorporation
The T oro Company , 81 1 1 L yndale A ve. South, Bloomington, MN, USA declares that the following unit(s)
conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain
T oro models as indicated on the relevant Declarations of Conformity .
Model No.
Serial No.
Product Description Invoice Description
General Description
Regulation
08719
—
Finish Brush Kit
SP2040Z FINISHING
BRUSH KIT
Broom Finishing Kit
S.I. 2008 No. 1597
Relevant technical documentation has been compiled as required per Schedule 10 of S.I. 2008 No. 1597.
W e will undertake to transmit, in response to requests by national authorities, relevant information on this partly
completed machinery . The method of transmission shall be electronic transmittal.
This machinery shall not be put into service until incorporated into approved T oro models as indicated on the
associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in
conformity with all relevant Directives.
This declaration has been issued under the sole responsibility of the manufacturer .
The object of the declaration is in conformity with relevant UK legislation.
Authorized Representative:
Marcel Dutrieux
Manager European Product Integrity
T oro U.K. Limited
Spellbrook Lane W est
Bishop's Stortford
CM23 4BU
United Kingdom
T om Langworthy
Engineering Director
81 1 1 L yndale A ve. South
Bloomington, MN 55420, USA
September 17, 2023