Toro 130-6020 User manual

FormNo.3393-700RevA
DeckLimitKit
2014andBeforeGroundsmaster®4000/4010RotaryMower
ModelNo.130-6020
InstallationInstructions
Thiskittsonmodels30603,30605,30607,and30609.
Note:Determinetheleftandrightsidesofthemachine
fromthenormaloperatingposition.
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato
causecancer,birthdefects,orreproductiveharm.
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescriptionQty.Use
1Nopartsrequired–Preparethemachine.
Axlebumper2
Leftbumperbracket1
Rightbumperbracket2
2Locknut2
Installtheaxlebumpersandbumper
brackets.
Bolt(#10x1-1/4inch)4
Bolt(#10x2inch)4
Washer8
Bumper4
Plate8
3
Locknut4
Installtheplatesandbumpers.
1
PreparingtheMachine
NoPartsRequired
Procedure
Positionthemachineonalevelsurface,settheparkingbrake,
lowerthecuttingunits,turntheignitionoff,andremovethe
key.
CAUTION
Ifyouleavethekeyintheignitionswitch,someone
couldaccidentlystarttheengineandseriously
injureyouorbystanders.
Removethekeyfromtheignitionswitchbeforeyou
doanymaintenance.
©2015—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.OriginalInstructions(EN)
PrintedintheUSA.
AllRightsReserved*3393-700*A

2
InstallingtheAxleBumpers
andBumperBrackets(Cab
MachinesOnly)
Partsneededforthisprocedure:
2Axlebumper
1Leftbumperbracket
2Rightbumperbracket
2Locknut
Procedure
1.Removethe2bolts,2lockwashers,and2washers
fromthebracketshowninFigure1.Saveallexisting
hardware.
Figure1
1.Washer3.Bolt
2.LockWasher
2.Installanaxlebumperontotheleftbumperbracket
andsecurewithalocknut(Figure2).
3.Usetheexistinghardwareyouremovedtoattachthe
brackettothemachine(Figure2).
Figure2
1.Axlebumper3.Existinghardware
2.Locknut
4.Adjusttheaxlebumpertoensureitwillcontactwith
thecab’sverticalpostandthedeckwillclearopenside
windowswhenthecuttingunitsareraised.
5.Repeattheprocedurefortherightbumperbracketon
therightsideofthemachine.
2

3
InstallingthePlatesand
Bumpers
Partsneededforthisprocedure:
4Bolt(#10x1-1/4inch)
4Bolt(#10x2inch)
8Washer
4Bumper
8Plate
4Locknut
Procedure
1.Removetheexistingbumpersfromtheleftsideofthe
machine(Figure3).
Figure3
1.Bumper
2.Installtheplatesandkitbumpersontothemachineas
showninFigure4.
Figure4
1.Locknut4.Washer
2.Plate5.Bolt(#10x2inch)
3.Kitbumper6.Bolt(#10x1-1/4inch)
3.Repeattheprocedurefortherightsideofthemachine.
3