Torque X-LAB-EDGE Series User manual

X-LAB-EDGE
Assembly Guide
PART #: 5582901-A
VERSION: XLE-X4

XLAB-501
XLAB-501
XLAB BOOT
XLAB BOOT
STEP 1
PAGE 2

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
1/2 X 4" BOLT (4)
1/2" FLAT WASHER (8)
1/2" LOCK NUT (4)
XLAB-501
GRT-101
XLAB-501
GRT-101
BATTLE ROPE
CONNECTOR
PAGE 3
STEP 2
LOOSELY assemble bolt connections in this step.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
XLAB-501
XLAB-501
XLAB-401
XLAB-401
1/2 X 3-1/2" BOLT (4)
1/2" FLAT WASHER (8)
1/2" LOCK NUT (4)
TOP CONNECTOR
PAGE 4
LOOSELY assemble bolt connections in this step.
STEP 3

XLAB-BOOT
XLAB-301
XLAB-301
XLAB-BOOT
PAGE 5
STEP 4

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
XLAB-301
XLAB-301
XLAB-401
XLAB-401
SUSPENSION
CROSS
1/2 X 3-3/4" BOLT (2)
1/2" FLAT WASHER (4)
1/2" LOCK NUT (2)
ANGLE CONNECTOR
ANGLE CONNECTOR
1/2 X 3-3/4" BOLT (2)
1/2" FLAT WASHER (4)
1/2" LOCK NUT (2)
PAGE 6
STEP 5
LOOSELY assemble bolt connections in this step.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
XLAB-301
XLAB-301
XLAB-501 XLAB-501
AT-101 AT-101
1/2 X 3-1/2" BOLT (4)
1/2" FLAT WASHER (8)
1/2" LOCK NUT (4)
1/2 X 3-1/2" BOLT (4)
1/2" FLAT WASHER (8)
1/2" LOCK NUT (4)
STEP 6
LOOSELY assemble bolt connections in this step.
PAGE 7

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
XLAB-301
XLAB-301
MID
CONNECTOR
BATTLE ROPE
HANGER
BATTLE ROPE
HANGER
AT-101
AT-101
1/2 X 3-1/2" BOLT (2)
1/2" FLAT WASHER (12)
1/2" LOCK NUT (6)
XLAB-501 XLAB-501
1/2 X 3-1/4"
BOLT (1)
1/2 X 3-1/4"
BOLT (1)
1/2 X 3-1/4"
BOLT (1)
1/2 X 3-1/4"
BOLT (1)
1/2 X 3-1/2" BOLT (2)
1/2" FLAT WASHER (12)
1/2" LOCK NUT (6)
1/2 X 3-3/4" BOLT (2)
1/2 X 3-3/4" BOLT (2)
PAGE 8
LOOSELY assemble bolt connections in this step.
NOTE: There are three different lenght bolts for this step. Follow diagram closely.
STEP 7

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
XLAB-301
XLAB-501
AT-101
1/2 X 3-1/2" BOLT (4)
1/2" FLAT WASHER (8)
1/2" LOCK NUT (4)
XLAB-501
XLAB-301
1/2 X 3-1/2" BOLT (4)
1/2" LOCK NUT (4)
1/2" FLAT WASHER (8)
AT-101
STEP 8
LOOSELY assemble bolt connections in this step.
PAGE 9

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
XLAB-301
XLAB-301
1/2 X 3-3/4" BOLT (2)
1/2" FLAT WASHER (4)
1/4" SPACER (2)
1/2" LOCK NUT (2)
ANGLE
CONNECTOR
1/2 X 3-3/4" BOLT (2)
1/2" FLAT WASHER (4)
1/4" SPACER (2)
ANGLE
CONNECTOR
1/2" LOCK NUT (2)
STEP 9
PAGE 10
ATTENTION:
AFTER THIS STEP HAS BEEN COMPLETED, SECURELY TIGHTEN THE
BOLT CONNECTIONS IN THIS STEP AND ALL PREVIOUS STEPS.

XCC-101
ANGLE
CONNECTOR
1/2 X 1-1/4" BOLT (4)
1/2" FLAT WASHER (8)
1/2" LOCK NUT (4)
1/2 X 1-1/4" BOLT (4)
1/2" FLAT WASHER (8)
1/2" LOCK NUT (4)
ANGLE
CONNECTOR (2)
XCC-101 TOP FRAME
XCC-101 BOTTOM FRAME
REPEAT STEP
ON THIS SIDE
REPEAT STEP
ON THIS SIDE
ATTENTION:
ASSEMBLE THE TOP AND BOTTOM FRAMES OF THE XCC-101 TO
THE ANGLE CONNECTORS AS SHOWN IN THIS STEP.
ASSEMBLE THE REST OF THE XCC-101 USING THE INSTRUCTIONS
INCLUDED WITH THAT PRODUCT.
STEP 10: XCC-101 ASSEMBLY
PAGE 11

ANCHOR
HOLES (4)
ANCHOR
HOLES (4)
ANCHOR
HOLES (4)
ANCHOR
HOLES (4)
ANCHOR
HOLES (4)
ANCHOR
HOLES (4)
BASE
PLATE
WARNING!
ALL XLABS ARE REQUIRED TO BE ANCHORED TO THE
FLOOR TO PREVENT ROCKING OR TIPPING DURING USE.
For additional information on anchoring XLABS to the floor,
please visit our web site: www.torquefitness.com/product tools/
assembly-manuals/X-SERIES ANCHORING INSTRUCTIONS
PAGE 12
ANCHOR STEPS:
1) Position machine in desired location.
2) Trace around the four base plates and the
four holes in each base plate.
3) Move machine.
4) Drill anchor holes. Follow instructions on
anchor bolt packaging.
5) Vacuum dust out of each anchor hole.
5) Move machine back over anchor holes.
6) Anchor machine. Follow instruction on
anchor bolt packaging.