Torque F9 User manual

F9 ASSEMBLY GUIDE
PART #: 5726401-B
VERSION: F9-003-150LB/200LB

Important safety instructions:
Important safety instructions for using equipment: Page 3 •
Important safety instructions for assembling equipment: Page 3 •
Obtaining service: Page 3 •
General Notes:
Unpacking equipment: Page 4 •
Tools Required: Page 4 •
Optional equipment: Page 4 •
Assembly tips: Page 4 •
Parts List: Page 5
Assembly Instructions: Pages 6 - 38
Adjustments and Maintenance:
Cable adjustments: Pages 32 & 35 •
Attachment and adjustment instructions: Page 39 •
Maintenance: Page 40 •
Resistance Ratio Chart: Page 41 •
TABLE OF CONTENTS
2

WARNING !
Important safety instructions for using Equipment
There is a risk assumed by the individuals who use this type of equipment. To minimize risk, you must follow these precautions:
READ ALL INSTRUCTIONS AND WARNING LABELS COMPLETELY PRIOR TO ANY USE OR ASSEMBLY. Failure to read and follow the safety instructions 1.
and warnings within the Assembly and Maintenance Guide may result in possible serious injury or death. Use this product only for the intended uses
described in the Assembly and Maintenance Guide and exercise booklet. DO NOT modify equipment in anyway. Any use other than as intended or
modification of product will void any and all product warranties.
Consult your physician before starting any exercise program. Warm up properly before engaging in resistance training. Stop exercising and consult a physician 2.
immediately
if you experience dizziness, nausea, faintness, chest pain, shortness of breath or any other abnormal symptoms during use of this equipment.
Certain exercise equipment and/or equipment may not be suitable or appropriate for pregnant women, people with heart conditions, balance impairment or other pre- 3.
existing health problems. Persons with disabilities should consult a physician and obtain medical approval prior to using this product and should only use this product
under close supervision. Failure to comply with these instructions will void any and all product warranties.
Carefully inspect equipment before each use. Replace all parts at the first sign of wear or damage. Tighten all loose connections. Pay special attention to cable ends 4.
and connections. Do not disassemble, remove any parts or components or otherwise attempt to repair this product. DO NOT use product if product appears damaged.
DO NOT attempt to fix a broken or jammed machine, obtain assistance from your authorized Torque Fitness Dealer. Failure to comply with these instructions will
void any and all product warranties.
Keep body and clothing clear of all moving parts. Do not put any foreign on or near this product when in use. Wear comfortable clothing which does not impair freedom 5.
of movement. Do not wear clothing which is too loose and could get caught in moving parts.
Make sure all adjustment spring pins are fully engaged after making an adjustment and before using the product. 6.
Make sure weight stack selector pin is completely inserted into the weight stack before beginning any exercise. 7.
Children and pets must not be allowed near this machine. Supervise teenagers. This product is not a toy. 8.
If unsure of proper use of this product, contact Torque Fitness Customer service at: 763-754-7533 (8:30 am - 5:00 pm CST). or 1-877-TORQUE5 (1-866-664-9894). 9.
[email protected]
Important Safety Instructions for Assembling Equipment
Assistance is required. Torque Fitness recommends using more than one person to assemble this equipment. 1.
This product must be assembled on a flat, level surface to assure its proper function. Locate the unit a few inches from walls or furniture to allow easy access 2.
during assembly and use.
Read each numbered step in Assembly and Maintenance Guide and follow the steps in sequence. Skipping ahead may result in damage to the equipment and 3.
may require components to be disassembled.
Wear proper attire during the assembly process. Do not wear clothing which is too loose or open toed shoes. 4.
Obtaining Service
Do not attempt to service the product yourself except for maintenance tasks described in this manual.
Refer to the Adjustments and Maintenance section at the back of this manual and the included workout booklet for information on product operation and service.
For further information, visit our website at www.torquefitness.com
or contact us at [email protected]
If you call or email customer service, have the model number and serial number(s) available. The location of the model and serial numbers are indicated in the back of this
manual. For future reference, write the model and serial number(s) in the space below.
Model Number:__________________________________________________________
Serial Number(s):________________________________________________________
3

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
4
GENERAL NOTES
CAUTION: More than one person is required to
assemble this unit. Do not attempt to assemble by
yourself.
Unpacking the Equipment
This product may be packaged and shipped in multiple
boxes. Parts from all of the boxes are required for
various steps during the assembly process.
Carefully open each box and arrange all the parts near
the area where assembly is to take place.
CAUTION:
Use extreme care when cutting plastic tie
wraps and package banding. A wire cutter works best
for protecting yourself and the parts.
CAUTION: Some of the internal boxes may contain
upholstery. Do not use a utility knife to open any
boxes or the pads may be damaged.
The hardware is packed in bags. Carefully open each
bag and sort them per parts list on the next page.
Before starting assembly, identify each part and
hardware item as listed in the parts list on the next
page. If any items are missing, contact Torque Fitness
Customer service at: 763-754-7533 (8:30 am - 5:00 pm
CST). or 1-877-TORQUE5 (1-866-664-9894).
[email protected]
Note: Some items listed in the parts list may already
be pre-installed on the product.
Tools Required
Rubber mallet or hammer •
3/4" Box wrench or adjustable wrench •
9/16" Box wrench or adjustable wrench •
Ratchet with 9/16" socket •
5/16" Allen wrench •
4mm Metric allen wrench •
Wire snips (to cut plastic tie wraps) •
Scissors or utility knife (to cut hardware •
bags)
Step stool or ladder •
Tape measure •
Optional Equipment
Optional equipment may be available for this product.
Follow the instructions included with the optional
equipment to assemble it to the base product.
Assembly Tips
In a continual effort to improve our •
products, specifications are subject to
change.
A 6" scale is provided at the bottom of •
every page. To correctly measure the
bolts, measure from underneath the bolt
head to the end of the bolt as illustrated
below.
Read all notes on each page before •
beginning that step.
Some of the items shown in the assembly •
steps may already be pre-assembled.
Assembly Tips Continued
Note: Some items have been hidden for •
assembly clarity.
Note: Some pre-assembled parts may •
need to be temporarily removed in order to
complete the step. Follow the instructions
or damage to the product could occur.
Some parts may have extra holes that will •
not be used. Use only the holes depicted
in the instructions.
Certain parts make reference to the right •
and left side of the machine. In order to
determine the left and right side, stand with
your back to the front of the machine.
Provide ample space around the product •
for ease of assembly.
DO NOT fully tighten any connections until •
instructed to do so. This will help insure
that the alignment of all of the parts will be
correct.
Insert all bolts in the direction indicated in •
the instructions. Failure to do so may result
in clearance issues and will degrade the
aesthetics of the product.
Carefully follow instructions for all pivot •
points. In general, primary rotating parts
have connections that should be securely
tightened, while secondary connections
need to be loosen 1/4 turn.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
*
**
ITEM PART NUMBER DESCRIPTION QTY
1 5496201 BRKT, LOWER BASE CONNECTOR 1
2 54844PA PTD ASSY, RIGHT SIDE 1
3 54858PA PTD ASSY, LEFT SIDE 1
4 5496301 PLATE, LOWER BASE PULLEY 2
5 2001101 WASHER, FLAT 3/8 SAE ST ZN 98
6 2008411 BOLT, 3/8-16 X 3" (76mm) ST HT SOCKET HEAD 8
7 2001201 NUT, 3/8-16 LK ST ZN 46
8 5094401 PULLEY, 3-1/2 OD X 25 4
9 5485601 SPACER, 16 OD X 10.1 ID X 12 4
10 5496401 BRKT, UPPER SIDE CONNECTOR 1
11 2008410 BOLT, 3/8-16 X 2-3/4" (70mm) ST HT SOCKET HEAD 14
12 54861PA PTD ASSY, ACCESSORY HOLDER 1
13 2001013 BOLT, 3/8-16 X 3-3/4" BUTTON HEAD 2
14 54866PA PTD ASSY, CHIN-UP 1
15 5489201 GUIDE ROD, 19 OD X 1880 4
16 57094PA PTD ASSY, 10 LB WEIGHT PLATE 28
17 57388PA PTD ASSY, 15 LB WEIGHT PLATE 20
18 57097PA PTD ASSY, HEAD PLATE 2
19 54896PA PTD ASSY, GUIDE ROD SUPPORT 2
20 5513601 CUSHION, WEIGHT STACK 4
21 5095301 SHAFT COLLAR, GUIDE ROD 4
22 2008409 BOLT, 3/8-16 X 2-1/2" (64mm) ST HT SOCKET HEAD 6
23 5487101 WLDMT, CARRIAGE UPRIGHT 2
24 5506601 ASSY, RIGHT CARRIAGE 1
25 54880PA PTD ASSY, RIGHT DOOR 1
26 2009403 BOLT, 3/8-16 X 1" (25mm) ST HT SOCKET HEAD W/NP 2
27 5511401 PIN, DOOR PIVOT 4
28 5506701 ASSY, LEFT CARRIAGE 1
29 54889PA PTD ASSY, LEFT DOOR 1
ITEM PART NUMBER DESCRIPTION QTY
30 5466201 WHEEL, 3" OD X 1/2" ID X 1-1/2" 2
31 5466601 SPACER, WHEEL HUB 2
32 2008406 BOLT, 3/8-16 X 1-3/4" (45mm) ST HT SOCKET HEAD 4
33 5172501 PULLEY, 3-1/2" IDLER 2
34 2009406 BOLT, 3/8-16 X 1-3/4" (45mm) ST HT SOCKET HEAD W/NP 2
35 5500701 LABEL, WEIGHT STACK 1-20 2
36 5666401 ASSY, WEIGHT STACK PIN 2
37 55181PA PTD ASSY, WEIGHT SELECTOR STORAGE PLATE 2
38 2009402 BOLT, 3/8-16 X 3/4" (19mm) ST HT SOCKET HEAD W/NP 4
39 54970PA PTD ASSY, HEAD PLATE PULLEY 2
40 2002601 NUT, 1/2 JAM ST ZN 4
41 5709301 CABLE ASSY, F9-103 2
42 5508801 HOUSING, CABLE COUPLER 2
43 5508901 GROMMET, RUBBER CABLE 2
44 5509001 CORE, CABLE COUPLER 2
45 2003201 CAP SCREW, M5 X 0.8 X 6MM SOCKET HEAD 4
46 5493201 PANEL, DOOR SIDE 2
47 5493001 SPACER, SHROUD STAND OFF 8
48 2008415 BOLT, 3/8-16 X 4" (102mm) ST HT SOCKET HEAD 8
49 5493301 SHROUD, DOOR FRONT 1
50 5493101 SPACER, SHROUD STAND OFF 4
51 2008417 BOLT, 3/8-16 X 4-1/2" (114mm) ST HT SOCKET HEAD 4
52 5497501 STRAP, UNIVERSAL 1
53 5324601-A ASSY, LEG BOOT D-RING 1
54 5324701-A ASSY, SHORT STRAP HANDLE 2
55 5497601 ASSY, SQUAT HARNESS W D-RING 1
56 55192PA PTD ASSY, STRAIGHT BAR 1
57 5091801 SNAP HOOK, 8MM DIA X 80MM 2
58 5493701 WORKOUT BOOK, F9-101 1
5
NOTE:
The F9 has two weight stack options. 150 LBS. and 200 LBS.
* The 150 LB. stack has fourteen 10 LB. plates and a head plate.
** The 200 LB. stack has ten 15 LB. plates, 4 ten LB. plates and a
head plate.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
2
3
1
5
7
6 3/8 X 3" (76mm)
4
6
LOOSELY assemble bolt connections in this step.
STEP 1

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
8
9
5
7
4
6 3/8 X 3" (76mm)
1
7
LOOSELY assemble bolt connections in this step.
STEP 2

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
98
5
7
4
6 3/8 X 3" (76mm)
1
8
LOOSELY assemble bolt connections in this step.
STEP 3

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
11 3/8 X 2-3/4" (70mm)
7
5
10
3 2
9
LOOSELY assemble bolt connections in this step.
STEP 4

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
5
7
12
11 3/8 X 2-3/4" (70mm)
5
7
2
3
13 3/8 X 3-3/4" (95mm)
10
LOOSELY assemble bolt connections in this step.
STEP 5

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
3
2
14
(2X)
11 3/8 X 2-3/4" (70mm)
5
7
11
After this step has been assembled, SECURELY tighten
all bolt connections from this step and previous steps.
STEP 6

2
20
16
15
19
21
18
150 LB OPTION
2
20
16
15
19
21
18
17
200 LB OPTION
12
STEP 7

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
7
5
11 3/8 X 2-3/4" (70mm)
7
5
2
22 3/8 X 2-1/2" (64mm)
15
21
19
NOTE:
Lift up on guide rod and
insert bolt underneath
Tighten set screws
13
SECURELY tighten all bolt connections in this step.
STEP 8

20
16
15
3
18
19
21
150 LB OPTION 200 LB OPTION
20
16
15
3
18
19
21
17
14
STEP 9

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
7
22 3/8 X 2-1/2" (64mm)
3
15
5
11 3/8 X 2-3/4" (70mm)
5
7
19
21
Tighten set screws
NOTE:
Lift up on guide rod and
insert bolt underneath
15
SECURELY tighten all bolt connections in this step.
STEP 10

24
23
16
STEP 11

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
11 3/8 X 2-3/4" (70mm)
5
7
23
25
26 3/8 X 1" (25mm) W/NP
5
17
STEP 12
SECURELY tighten all bolt connections in this step.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
25
2
27
27
18
SECURELY tighten all bolt connections in this step.
STEP 13

28
23
19
STEP 14

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
26 3/8 X 1" (25mm) W/NP
5
11 3/8 X 2-3/4" (70mm)
5
7
29
23
20
SECURELY tighten all bolt connections made in this step.
STEP 15