Torque TANK User manual

TANK
Assembly Guide
PART #: 5706201-A
VERSION: XTTM1-RPH-101

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
ITEM PART NUMBER DESCRIPTION QTY
1 5661401 ASSY, CHASSIS WITH BRAKE SYSTEM 1
2 5661501 ASSY, REAR FRAME 1
3 2024401 WASHER, 8.4MM X 16MM X 1.8MM CLEAR ZINC 8
4 2009801 SCREW, M8-1.25 X 20L SOC HD GR 12.9 8
5 2010801 WASHER, STEEL 12.7 ID-25 OD-2 THK CLEAR ZINC 2
6 5654501 ASSY, REAR WHEEL 10" DIA X 3" WIDE 2
7 2010901 WASHER, LOCK M12 SAE ST ZN 2
8 2011301 SCREW, M12-1.75 X 30L SOC HD GR 12.9 CLEAR ZINC 2
9 56930PA PTD ASSY, RH PUSH HANDLE 1
10 56931PA PTD ASSY, LH PUSH HANDLE 1
11 57144PA PTD ASSY, UPPER MOUNT (OPTIONAL) 1
12 57145PA PTD ASSY, LOWER MOUNT (OPTIONAL) 1
13 2001101 WASHER, FLAT 3/8 SAE ST ZN 8
14 2031101 SCREW, 3/8" LAG X 2.5"L CLEAR ZINC 8
2
TABLE OF CONTENTS:
TANK ASSEMBLY: PAGES 3 - 5 •
TANK STORAGE (OPTIONAL): 6 - 8 •
ADJUSTMENTS: 9 - 10 •
INSPECTION & LUBRICATION: PAGE 11 •
TOOLS NEEDED FOR ASSEMBLY:
10MM ALLEN WRENCH (INCLUDED) •
6MM ALLEN WRENCH (INCLUDED) •

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
2
1
3
4
3
NOTE:
LOOSELY tighten bolt connections in this step.
STEP 1

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
2
6
5
7
8
NOTE:
BEFORE ASSEMBLING TIRES, CHECK
TIRE PRESSURE. MAKE SURE TIRES
ARE INFLATED TO 30 PSI
NOTE:
AFTER TIRES HAVE BEEN
SECURELY ASSEMBLED,
SECURELY TIGHTEN THESE
BOLTS.
4
NOTE:
SECURELY tighten all bolt connections in this step and previous step.
STEP 2

10
9
NOTE
ALIGN THE "L" LABEL ON THE LEFT HANDLE
WITH THE "L: LABEL ON THE REAR FRAME
NOTE
ALIGN THE "R" LABEL ON THE RIGHT HANDLE
WITH THE "R: LABEL ON THE REAR FRAME
2
NOTE:
ALIGN THE PIN IN THE PUSH
HANDLES WITH THE SLOT IN
THE RECEIVER TUBE
5
STEP 3

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
11
12
13
14
1-3/4"
1-3/4"
35"
6" (MIN)
FLOOR
WARNING:
THE LOWER MOUNT MUST BE ANCHORED TO THE WALL
USING FOUR WALL ANCHORS SUITABLE FOR THAT
PARTICULAR WALL CONSTRUCTION.
WARNING:
THE UPPER MOUNT MUST BE ANCHORED TO THE WALL
USING FOUR WALL ANCHORS SUITABLE FOR THAT
PARTICULAR WALL CONSTRUCTION.
XTWMH
WALL MOUNT HANGER (OPTIONAL)
NOTES:
The images above show the anchoring hardware used for attaching
to typical walls with wood studs spaced 16" on center. The anchors
used will depend on the wall construction. In all cases, at least four
anchoring locations must be used. The pull-out strength of the
anchoring bolts used must be greater than or equal to 200 lbs. (91 kg)
SECURELY tighten bolt connections in this step.
6

NOTE:
THE FRONT TIRE WILL REST ON
THIS SURFACE WHEN STORED
11
12
2
XTWMH
WALL MOUNT HANGER (OPTIONAL)
7

NOTE:
ALIGN THE PIN IN THE PUSH
HANDLES WITH THE SLOT IN
THE RECEIVER TUBE (2X)
10
9
12
8
XTWMH
WALL MOUNT HANGER (OPTIONAL)

PULL SPRING PIN AND ROTATE
TOW BAR FORWARD UNTIL IT
ENGAGES FRONT HOLE
ATTACH TOW
STRAP HERE
NOTE:
THE TOW BAR MUST BE ADJUSTED
FORWARD TO ADD WEIGHT PLATES
TO THE WEIGHT HORN
TOW BAR
9
XTTM1 TOW BAR ADJUSTMENT

PULL BACK ADJUSTER TO INCREASE RESISTANCE
POSITION N: NEUTRAL
POSITION 1: LOW RESISTANCE
POSITION 2: MEDIUM RESISTANCE
POSITION 3: HARD RESISTANCE
10
XTTM1 RESISTANCE ADJUSTMENT

NOTE:
TO REMOVE SHROUD,
LOOSEN AND REMOVE
6 SCREWS AS SHOWN
BOTTOM VIEW
11
INSPECTION & LUBRICATION
INSPECTION:
ATTENTION:
PLEASE ENSURE THAT ALL TIRES ARE INFLATED
TO 30 PSI. FAILURE TO DO SO MAY RESULT IN
TANK VEERING DURING USE.
Once a month, check for loose bolts on frame and
wheels. Tighten if necessary.
Once a month, remove shroud and check that the
chain and sprockets are clean, free of rust, dust
and grime. Make sure that the chain is properly
lubricated.
LUBRICATION:
Once a month, the sprockets should be cleaned and
the chain should be lubricated.
RECOMMENDED LUBRICATION: Use a Dry lubrication
for indoor use, and wet lubrication for outdoor use.
Most bicycle shops carry a variety of different
lubricants and can recommend a lubricant based on
the conditions where the TANK will be used.