Toshiba B-EP700-BLTH-QM-R User manual

EO2-38061
1/8
TOSHIBA Bluetooth Module
B-EP700-BLTH-QM-R Installation Manual
Thank you for purchasing TOSHIBA Bluetooth module, B-EP700-BLTH-QM-R.
The B-EP700-BLTH-QM-R is an optional Bluetooth module for the B-EP2DL/EP4DL Series.
The pictures used in this document are those of the B-EP4DL, but the installation procedure is common with the
B-EP2DL unless otherwise noted.
1. PACKING LIST
The following parts are supplied with the kit. Make sure you have all items shown below.
Bluetooth Module (1 pc.)
Installation Manual (1 copy)
Standard Label (1 pc.)
FPC Cable
1. Follow all manual instructions. Failure to do so could create safety hazards such as fire or electrocution.
• Manual instructions must be followed when installing option kits or adding cables to avoid system
failures and to insure proper performance and operation.
• Failure to follow manual instructions or any unauthorized modifications, substitution or change to this
product will void the limited product warranty.
2. Turn the power off and remove the battery before installing the Bluetooth module.
3. Be careful not to pinch your fingers or hands with the covers.
WARNING!
For B-EP2DL Series (1pc.)
Connected to
Bluetooth module
Connected to
Main PCB
For B-EP4DL Series (1pc.)
Connected to
Bluetooth module
Connected to
Main PCB

2/8
2. INSTALLATION PROCEDURE
Step 1. Turn off the printer.
Step 2. Slide the battery lever in the direction of the arrow, and remove the battery pack from the printer.
Step 3. Remove the four tapping screws from the bottom cover.
Step 4. Press the top cover open button to open the top cover.
Step 5. Remove the left side cover in the direction of the arrow.
NOTE: The gears shown in the picture below is not secured and is easily removed. Be careful not to drop
and break or lose it.
B-EP4DL Series B-EP2DL Series
Gea
r
Top Cover
Top Cover Open Button Left Side Cover
Gea
r
Gear
T-3x10 Tapping Screw
T-3x10 Tapping Screw
Battery Pack
Battery
Lever

3/8
Step 6. Remove the right side cover and the front cover in the direction of the arrow, respectively.
Step 7. Connect the FPC cable to the Bluetooth module in the correct orientation.
Two FPC cables are supplied with the Bluetooth module. One is designed for the B-EP2DL series, and
the other is for the B-EP4DL series. Care must be taken not to mistake them for each other.
NOTE: Pass the FPC cable through the slot, as shown in the picture below. (B-EP4DL series only)
Step8. Connect the FPC cable to the CN301 connector on the Main PC board in the correct orientation.
Main PC Board
CN301
FPC Cable
Bluetooth
Module
FPC Cable
Slot
Right Side Cover
Front Cove
r

4/8
Step9. Fit the Bluetooth module into the following position.
Pass the FPC cable as shown below so that they do not get caught on the gears or by the cover.
Step10. Close the front cover.
NOTES: 1. Make sure that the pins on the both sides of the front cover are fit in position, as shown in the pictures
below.
2. Do not install the front cover with the top cover open button depressed. Doing so could disable the top
cover open button after the assembly, and as a result, the top cover cannot be opened.
Front Cover
B-EP4DL
FPC Cable
Pin
To
p
Cover O
p
en Button
Good No Good
B-EP2DL
FPC Cable
Bluetooth Module
Bluetooth Module

5/8
Step11. Mount the left side cover to the printer while fitting the tabs on the left side cover into the slots of the
printer enclosure. Place the cables avoiding the protrusions on the left side cover. Especially, be
careful of the protrusion E on the cover for the B-EP2DL series.
B-EP4DL Series: Fit the tabs A to D into the slots A’ to D’.
B-EP2DL Series: Fit the tabs A to C into the slots A’ to C’.
NOTE: It is easy to mount the left side cover if you fit the tabs from the LCD side in order, then secure the
bottom side. Be careful not to catch the cable by the cover while reassembling.
Tab
A
Tab B Tab C Tab D
A
’
B’
C’
D’
Tab
A
Tab C
Tab B
A
’
B’
C’
Left Side Cove
r
Protrusion
E
Protrusion

6/8
Step12. Mount the right side cover to the printer while fitting the tabs on the right side cover into the slots of the
printer enclosure.
B-EP4DL Series: Fit the tabs A to C into the slots A’ to C’.
B-EP2DL Series: Fit the tabs A to C into the slots A’ to C’.
NOTE: It is easy to mount the right side cover if you fit the tabs from the LCD side in order, then secure the
bottom side. Be careful not to catch the cable by the cover while reassembling.
Tab A
Tab BTab C
A
’
B’
C’
Tab A
Tab B
Tab C
A
’
B’
C’
Right Side Cover

7/8
Step13. Close the top cover and load the battery pack.
Step14. Attach the supplied Standard Label to the following position.
Step15: Configure the Bluetooth module settings in the system mode with reference to the Key Operation
Specification or Service manual.
For how to configure the Bluetooth Module settings by the B-EP Setting Tool, please refer to B-EP
Setting Tool Operation Manual.
Precautions for Handling of Wireless Communication Devices
Bluetooth® Module: TEC-BTM-R (B-EP700-BLTH-QM-R)
Trade Mark
Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. and used byTOSHIBA TEC CORPORATION under
license.
Cautions
General
For all countries and areas
This product is a wireless communication device, and the use of thisproduct is restricted to the following countries or
areas. If the product isused in the countries or areas other than the following, you may bepunished according to the laws
of those countries or areas.
USA, Canada, Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany,
Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, United Kingdom, Switzerland, Norway, Iceland, Liechtenstein, Australia,
New Zealand, Mexico
For Europe
for Bluetooth
Hereby, TOSHIBA TEC CORPORATION, declares that the TEC-BTM-R is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC. This equipment uses a radio frequency band that has not been
harmonized throughout all EU and EFTA countries, and can be used in EU and EFTA countries.
For USA
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, includinginterference that may cause undesired operation.
Changes or modification not expressly approved by manufacturer forcompliance could void the user’s authority to
operate the equipment.
Standard Label Standard Label
B-EP2DL Series
B-EP4DL Series

8/8
For Canada
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from
windows to provide maximum shielding. Equipment that is installed outdoors is subject to licensing.
For safety
Do not use this product in locations where use may be forbidden, for example,in an aeroplane or a hospital. If you do not
know the forbidden areas, please referto and follow the airline company or medical institution guidelines.
Flight instrument or medical equipment may be affected, causing a serious accident.
Since this product uses extremely low power compared with mobile phones, itcannot possibly interfere the pacemakers
and defibrillators. However, if the useof this product should be likely to have affected the pacemaker or
defibrillator,immediately stop using the product and contact your TOSHIBA TEC sales agent.
Do not disassemble, modify, or repair the product. Doing so may cause injury. Also, modification is against the Laws
and Regulations for Radio Equipment. Please ask your TOSHIBA TEC sales agent for repair.
Precaution in use
This product communicates with other devices by radio. Depending on the installation location, orientation, environment,
etc., its communication performance may deteriorate or devices installed near by may be affected.
Keep away from a microwave.
Communication performance may deteriorate or a communication error may occur due to the radio emitted from a
microwave.
Since the Bluetooth and wireless LAN use the same radio frequency band, each radio wave may interfere with each
other when they are used at the same time, causing a deterioration of communication performance or a disconnection of
network. If there is any problem with connection, please stop using either Bluetooth or wireless LAN.
Do not use the product on a metal table or near a metal object.
Communication performance may be deteriorated.
TEC-BTM-R Specification
• Bluetooth class 2
• Built-in protocol stack activated by Bluetooth V1.2 serial port profile
• Operating temperature (When installed to the printer): -5 to 50°C, 25% to 85%RH (No condensation)
• Dimensions: 38.1 mm (W) x 25.4 mm (H) x 7 mm (D)
PRINTED IN SINGAPORE
EO2-38061