Toshiba IK-CT1C User manual

For Customer Use
Enter below the Serial #
which is located on the
bottom of the cabinet. Retain
this information for future ref-
erence.
Model # IK-CT1C
Serial #
CAMERA CONTROL UNIT INSTRUCTION MANUAL
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursu-
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
USER-INSTALLER CAUTION: Your authority to operate this FCC verified equipment could be voided if
you make changes or modifications not expressly approved by the party responsible for compliance to
Part 15 of the FCC Rules.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est comforme à la norme NMB-003 du Canada.
Following information is only for EU-member states:
The use of the symbol indicates that this product may not be treated as household waste.
By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed information about the take-
back and recycling of this product, please contact your supplier where you purchased the
product or consult.
This manual is made from recycled paper.
IK-CT1C
IK-CT1CEN.indd1IK-CT1CEN.indd1 2008/02/1412:12:432008/02/1412:12:43

2
SAFETY PRECAUTIONS
Safety icons
This manual contains safety instructions that must be observed in order to avoid potential
hazards that could result in personal injuries, damage to your equipment, or loss of data.
These safety cautions have been classified according to the seriousness of the risk, and the
icons highlight these instructions as follows:
Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
Stop operation immediately if any abnormality or defect occurs.
Use during an abnormal condition; such as emitting smoke, burning odors, damage
from dropping, invasion of foreign objects, etc. may result in fire and/or electrical
shock. Immediately disconnect the power source and contact your dealer.
Avoid installing in a shower room or a bathroom.
This may result in fire and/or electrical shock.
Do not operate in places where the product may get wet.
This may result in fire and/or electrical shock.
Do not repair, disassemble and/or modify by yourself.
This may result in fire and/or electrical shock. Always be sure to contact your
dealer for internal repair, check and cleaning of the product.
Use the specified power supply.
Otherwise, fire or electrical shock may occur.
Do not place anything on top of the unit.
Foreign materials, such as metals or liquids, getting into the product may result
in fire and/or electrical shock.
Do not put the product on an unstable, slanted or vibrating surface.
The product dropping or falling may result in serious injury.
Do not touch the product or any connection cables during a thunder-
storm.
This may result in electrical shock.
IK-CT1CEN.indd2IK-CT1CEN.indd2 2008/02/1412:12:432008/02/1412:12:43

3
Disclaimer
We disclaim any responsibility and shall be held harmless for any damages or losses incurred by the
The following description is for that a camera head “IK-CT1H” connected to this camera control unit.
user in any of the following cases:
1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether inten-
tional or accidental; use under extreme operating conditions.
2. Malfunction or non-function resulting in indirect, additional or consequential damages, including
but not limited to loss of expected income and suspension of business activities.
3. Incorrect use not in compliance with instructions in this instruction manual.
4. Malfunctions resulting from misconnection to other equipment.
5. Repairs or modifications made by the user or caused to be made by the user and carried out by
an unauthorized third party.
6. Notwithstanding the foregoing, Toshiba’s liabilities shall not, in any circumstances, exceed the
purchase price of the product.
Copyright and Right of Portrait
There may be a conflict with the Copyright Law and other laws when a customer uses, displays,
distributes, or exhibits an image picked up by the camera without permission from the copyright
holder. Please also note that transfer of an image or file covered by copyright is restricted to use
within the scope permitted by the Copyright Law.
Protection of Personal Information
Note the following instructions when installing.
• Do not cover the product with any material.
• Do not place the product on any inflammable material such as a carpet or
• Do not place the product in a confined space, as this may cause heat to
build up inside the product.
blanket.
Failure to follow the above cautions may result in fire.
Do not place the product in direct sunshine and/or high temperature.
Temperature build up inside the product may result in fire.
Avoid placing in humid, smoky, or dusty places.
This may result in fire and/or electrical shock.
Do not point the lens directly at the sun and/or intensive light such as di-
rect sunlight, etc.
Focusing of the light may result in eye injury and/or fire.
Ask your dealer to perform a periodical check and internal cleaning (approx.
once every five years).
Dust inside the product may result in fire. For check and cleaning cost, please
consult your dealer.
Images taken by the camera that reveal the likeness of an individual person may be considered
personal information. To disclose, exhibit or transmit those images over the internet or otherwise,
consent of the person may be required.
IK-CT1CEN.indd3IK-CT1CEN.indd3 2008/02/1412:12:432008/02/1412:12:43

4
1CAUTIONS ON USE AND INSTALLATION
(for a Camera Head and Camera Control Unit) .......................................
2 COMPONENTS .......................................................................................
3 ITEMS CONTROLLED BY THE ON SCREEN DISPLAY........................
4 NAMES AND FUNCTIONS......................................................................
5 CONNECTION........................................................................................
5.1 Standard Connection ..................................................................................................
5.2 Cautions on Connection..............................................................................................
5.3 Connection on Rear Panel..........................................................................................
6 OPERATION...........................................................................................
6.1 Initializing...................................................................................................................
6.2 White Balance.............................................................................................................
6.3 Scene File ...................................................................................................................
6.4 Gain.............................................................................................................................
7 MODE SETTING BY THE ON SCREEN DISPLAY ................................
7.1 Using the Menus .........................................................................................................
7.2 Menus .........................................................................................................................
(1) SHUTTER (Electronic shutter) ....................................................................................
(1.1) AUTO mode .......................................................................................................
(1.2) MANUAL mode ..................................................................................................
(1.3) SS (Synchro. Scan) mode .................................................................................
(2) GAIN (Video gain) .......................................................................................................
(2.1) GAIN mode ..........................................................................................................
(2.3) MANUAL mode ..................................................................................................
(3) WHT BAL (White Balance).........................................................................................
(3.1) WHT BAL mode ...............................................................................................
(3.2) AWB (Automatic White Balance) mode ...............................................................
(3.3) ATW mode ...........................................................................................................
(3.4) MANUAL mode ....................................................................................................
(4) PROCESS ...................................................................................................................
(4.1) Gamma correction ON/OFF ...............................................................................
(4.2) Detail (outline) gain setting .................................................................................
(4.4) Pedestal setting ..................................................................................................
(4.3) DNR (Digital Noise Reduction) ...........................................................................
(5) MATRIX(Matrix color correction) .................................................................................
(5.1) Matrix color correction ON/OFF ..........................................................................
(5.2) MATRIX setting ...................................................................................................
6
6
7
8
9
9
10
1010
11
11
12
14
14
15
15
16
16
17
20
21
22
22
23
(2.2) AUTO mode ........................................................................................................ 22
24
24
24
25
25
26
26
26
26
26
27
27
27
TABLE OF CONTENTS
Limitation of Usage
The product is not designed for any “critical applications.” “Critical applications” means life support
systems, exhaust or smoke extraction applications, medical applications, commercial aviation, mass
transit applications, military applications, homeland security applications, nuclear facilities or systems
or any other applications where product failure could lead to injury to persons or less of life or
catastrophic property damage. Accordingly, [Toshiba/TAIS] disclaims any and all liability arising out of
the use of the product in any critical applications.
IK-CT1CEN.indd4IK-CT1CEN.indd4 2008/02/1412:12:432008/02/1412:12:43

5
8BEFORE MAKING SERVICE CALL........................................................
9 SPECIFICATIONS..................................................................................
10 EXTERNAL APPEARANCE DIAGRAM................................................
33
34
35
(6) OPTION.......................................................................................................................
(6.1) FREEZE INPUT setting......................................................................................
(6.2) FREEZE MODE setting ......................................................................................
28
28
28
(6.3) FREEZE DISPLAY setting..................................................................................
(6.4) TITLE DISPLAY setting ......................................................................................
29
29
(6.5) TITLE POS (Position) setting..............................................................................
(6.6) Editing TITLE .....................................................................................................
30
31
(6.7) RS232C baud rate ............................................................................................. 31
(7) Returning to factory settings ....................................................................................... 32
IK-CT1CEN.indd5IK-CT1CEN.indd5 2008/02/1412:12:432008/02/1412:12:43

6
1 Camera Control Unit ............................................................................................... 1
2 Accessories
Instruction manual................................................................... ............................1
2. COMPONENTS
1. CAUTIONS ON USE AND INSTALLATION (for a Camera Head and Camera Control Unit)
•Handling the unit.
•Do not shoot intense light.
If there is an intense light at a location on the
screen such as a spot light, a blooming and smear-
ing may occur. When intense light enters, vertical
stripes may appear on the screen. This is not a
malfunction. Ghosts may occur when there is an
intense light near the object. In this case, change
the shooting angle.
•Install the camera in a location free from noise.
If the camera or the cables are located near power
utility lines or a TV, etc. undesirable noise may ap-
pear on the screen. In such a case, try to change
the location of the camera or the cable wiring. •Moire
•Operating ambient temperature and humidity.
Do not use the camera in places where tempera-
ture and humidity exceed the specifications. Pic-
ture quality will deteriolate and internal parts may
be damaged.
Be particularly careful when using in places ex-
posed to direct sunlight. When shooting in hot
places, depending on the conditions of the object
and the camera (for example when the gain is in-
creased), noise in the form of vertical strips or
white dots may occur. This is not a malfunction.
•Handling of the camera head.
•When not using the camera for extended
periods of time.
•When cleaning the camera.
•Avoid using or storing the camera in the fol-
lowing places:
•Camera installation
Do not drop, jolt, or vibrate, as this may result in
damage to the unit. This may cause problems.
Treat the camera cables carefully to prevent
cable problems, such as breaks in the cable and
loose connections.
Keep the camera head away from children as it
may pose a choking hazard.
Unplug the power source before cleaning. Clean
with a soft dry cloth only. Do not use chemicals or
chemically treated cloths. Chemicals may damage
coatings and printed letters. When cleaning the
lens, use lens cleaning paper.
The camera head has no threaded holes. If using
a clip, holder or similar mounting device, please
install it carefully and with caution on the cable
side edge.
Please prevent unnecessary pressure on the
head.
Places filled with highly flammable gas.
Places near gasoline, benzene, or paint thinner.
Places subject to strong vibration.
Places containing chemicals (such as pesticides),
rubber or vinyl products for extended periods of
time.
Switch the control unit off and disconnect the
power supply.
A moire pattern is an interference pattern
generated when two repetitive line patterns
overlap. This is not a malfunction. Eliminating the
repetitive line patterns, or aligning the two
patterns, will eliminate the moire.
The following descriptions are for that a camera
head "IK-CT1H" connected to this camera control
unit.
IK-CT1CEN.indd6IK-CT1CEN.indd6 2008/02/1412:12:432008/02/1412:12:43

7
3ITEMS CONTROLLED BY THE ON SCREEN DISPLAY
●Available Item and Preset value in MENU display
Item Available selections Preset value
(Factory setting)
SHUTTER MODE AUTO, MANUAL, SS MANUAL
MANUAL OFF, 1/100 ～1/10000 OFF
MAX EXP. OFF, 1FRM ～128FRM OFF
LEVEL -100 ～0 ～100 0
PEAK ／AVE 00:10 ～05:05 ～10:00 05:05
SPEED 1 ～10 5
AREA PRESET A, B, C, D, E, USER PRESET A
AREA DISP OFF OFF
SS 9/525H ～260/525H, OFF, 1FRM ～128FRM OFF
GAIN MODE OFF, AUTO, MANUAL OFF
MAX GAIN 0dB ～20dB 10dB
PRIORITY AGC ＞LONG, LONG ＞AGC AGC ＞LONG
MANUAL 0dB ～20dB 0dB
WB MODE AWB, MANUAL, ATW AWB
R PAINT (AWB) -10 ～0 ～10 0
B PAINT (AWB) -10 ～0 ～10 0
R GAIN (MANU) -100 ～0 ～100 0
B GAIN (MANU) -100 ～0 ～100 0
R PAINT (ATW) -10 ～0 ～10 0
B PAINT (ATW) -10 ～0 ～10 0
PROCESS GAMMA ON/OFF ON, OFF ON
DTL GAIN OFF, 1 ～10 5
DNR ON, OFF ON
PEDESTAL -10 ～0 ～10 0
MATRIX MATRIX ON, OFF OFF
R HUE -15 ～15 0
R GAIN -15 ～15 0
G HUE -15 ～15 0
G GAIN -15 ～15 0
B HUE -15 ～15 0
B GAIN -15 ～15 0
Ye HUE -15 ～15 0
Ye GAIN -15 ～15 0
Cy HUE -15 ～15 0
Cy GAIN -15 ～15 0
Mg HUE -15 ～15 0
Mg GAIN -15 ～15 0
OPTION FREEZE INPUT FRONT, TRIG , TRIG FRONT
FREEZE MODE FIELD, FRAME FIELD
FREEZE DISP ON, OFF ON
TITLE DISP ON, OFF OFF
TITLE POS TOP LEFT, TOP RIGHT,
BOTTOM LEFT, BOTTOM RIGHT
TOP LEFT
EDIT TITLE OFF OFF
BAUD RATE 9600bps, 19200bps 9600bps
IK-CT1CEN.indd7IK-CT1CEN.indd7 2008/02/1412:12:432008/02/1412:12:43

8
3
4
2
2
1
1
54321
78 6 9
FILE button
POWER switch
POWER LED
FREEZE button
S-VIDEO terminal
TRIGGER terminal
DC IN 12V terminal
DVI terminal
Camera cable
terminal for IK-CT1H
DISP button
MENU UP button
DATA UP (AWB) button
DATA DOWN button
MENU DOWN button
PAGE button
VIDEO terminal
REMOTE terminal
KEY LOCK switch
4. NAMES AND FUNCTIONS
[Front]
[Rear]
㽲Camera cable terminal for
IK-CT1H
Where the camera cable for IK-CT1H is connected.
㽳POWER LED Illuminates to indicate the unit is powered on.
㽴POWER switch Turns power on or off.
㽵FILE button To switch the scene files.
㽶FREEZE button Used when enabling freeze function.
㽷DISP button Changes the display mode.
㽸PAGE button To switch and select menus.
㽹MENU UP button To select the function to be confirmed or changed on the menu.
㽺MENU DOWN button To select and confirm the function or to change the menu.
㽻DATA UP (AWB) button To change the value of the function selected by the MENU (UP/DOWN) button.
(Also used when using AWB.)
㽼DATA DOWN button To change the value of the function selected by the MENU (UP/DOWN) button.
(Also used when using INITIALIZE.)
㽽DC IN 12V terminal Accepts a DC power input (12V).
IK-CT1CEN.indd8IK-CT1CEN.indd8 2008/02/1412:12:432008/02/1412:12:43

9
㽿S-VIDEO terminal
㾀VIDEO terminal
Outputs Y or C.
Outputs VBS signal on a monitor or VTR etc.. (BNC connector)
㾁DVI terminal Outputs DVI to connect to a monitor.
㾂KEY LOCK switch Disables functions of 㽵to 㽼buttons when KEY LOCK switch is ON.
㾃REMOTE terminal Used when controlling the function by RS-232C.
㽾TRIGGER terminal Control TRIGGER terminal for freeze function. Used when FREEZE INPUT in
OPTION menu is set to TRIG , or TRIG (Refer to the item “7.2 (6)
OPTION”. Terminal 1 (IN) and Terminal 2 (GND) are connected to the switch by
two wires. Switching open or close makes FREEZE function controlled.
When switch opens in TRIG setting or closes in TRIG setting,
FREEZE screen and normal screen can be switched.
5CONNECTION
5
5. 1 -1 Analog Connection
1 Standard Connection
5. 1 -2 DVI Connection
IK-CT1H
Camera Head
(option)
IK-CT1H
Camera Head
(option)
Camera
Control unit
DC power supply
(option)
DC power supply
(option)
DC IN 12V
DC IN 12V
IK-CT1C
Camera
Control unit
IK-CT1C
VIDEO
terminal
or S-VIDEO
terminal
Coaxial Cable
75Ω or S-VIDEO
Cable
(not supplied)
Monitor
(not supplied)
DVI terminal
DVI Cable
(not supplied)
DVI monitor
(DVI-A or DVI-D)
(not supplied)
IK-CT1CEN.indd9IK-CT1CEN.indd9 2008/02/1412:12:432008/02/1412:12:43

10
DC IN 12V
1 +12V
2 +12V
3 GND
4 GND
REMOTE
1
2
3
4
5
6
7
8
9 NC
NC
NC
NC
GND
NC
RXD
TXD
NC
TRIGGER
1
2GND
IN
䊶Only use optional camera head model # IK-CT1H with this camera controller.
The use of another head may cause damage to the control unit and camera head.
䊶When connecting the camera cables, be sure to turn off the camera control unit and
any other equipment connected to it.
䊶For DC power supply connecting to DC IN 12V terminal, use UL listed and/or CSA
approved ungrounded type AC adaptor with the specifications described below.
Power supply voltage 䋺12V DC 㫧10%
Current rating 䋺More than 1.0A
Ripple voltage 䋺Less than 50mV (p-p)
Connector 䋺HR10A-7P-4S by HIROSE electronics Co. Ltd
Pins 1, 2 䋺12V
Pins 3, 4 䋺GND
䊶If the securing screw on the connector of the camera cable loosens, noise may appear
on the screen. Be sure to tighten the connector completely.
Rear panel view
5 2 Caution on Connection
5 3 Connection on Rear Panel
The rear panel has basic connection terminals ; DC IN 12V, TRIGGER, S-VIDEO, VIDEO, DVI, and
REMOTE terminal. Use them as necessary.
54321
7869
3
4
2
1
2
1
IK-CT1CEN.indd10IK-CT1CEN.indd10 2008/02/1412:12:442008/02/1412:12:44

11
㽲Refer to the item “5. CONNECTION”, connect the equipment correctly.
A camera head "IK-CT1H" needs to be connected to this camera control unit from this section on.
㽳Turn on the connected equipment and the camera.
㽴When using the camera for the first time and when replacing the camera cable and the camera head, be
sure to perform the ABB adjustment, refer to the item “6.1 Initializing”.
㽵
㽶
Refer to the item “6.2 White Balance”, make the adjustment.
Refer to the items “6.3 Scene File, 6.4 Gain, 7. MODE SETTING BY THE ON SCREEN DISPLAY”,
select the necessary items.
Initilizing is necessary when the camera head is changed or used for the first time after purchase.
䊶Close the lens iris not to stream. Streaming makes adjustment difficult.
䊶If the color bar pattern is displayed on the screen or if the index menu/menu is displayed, press the [DISP]
button to disable the color bar pattern or the character display.
䊶Hold the [DATA DOWN] button for approx. 1 second.
䊶When initializing starts, the character INITIALIZE blinks on the screen.
䊶When initializing finishes, the character INITIALIZE stops blinking and the result appears for
approx. 1 second.
MeaningDisplay
INITIALIZE OK Initializing finished correctly.
INITIALIZE NG
CLOSE LENS
Initializing cannot be performed because the lens iris is open.
Close the lens iris.
INITIALIZE NG Initializing cannot be performed.
Try initializing again.
6OPERATION
6 1 Initializing
IK-CT1CEN.indd11IK-CT1CEN.indd11 2008/02/1412:12:442008/02/1412:12:44

12
ATW
Automatic Tracking
White Balance䋩
䋩䋩
䋩
AWB
䋨
䋨䋨
䋨䋨
䋨䋨
䋨Automatic White Balance䋩
䋩䋩
䋩
MANUAL
䋨
䋨䋨
䋨Manual White Balance䋩
䋩䋩
䋩
Outline
The camera measures the
object color temperature and
adjusts the white balance
automatically.
Adjust white balance by
displaying the white object
inside the area set by AWB
menu and pressing the
[DATA UP] button.
Adjust the white balance
manually using the WHT
BAL menu while shooting
the white object.
Features
Tracks variations of color
temperature and adjusts white
balance automatically.
Measurement accuracy is
higher than ATW. This
mode is effective when
shooting under less varia-
tions of color temperature.
Artificial white balance setting.
The manual adjustment is
most effective under shooting
conditions with no color
temperature variation.
Notes
If illumination is low, white
balance may not be corrected.
Adjustment is performed by
confirming with a vector
scope.
㽲AWB(Automatic White Balance)
䊶Set the MODE to AWB on the WHT BAL menu.
䊶If the color bar pattern is displayed on the screen or if the index menu/menu is displayed, press the [DISP]
button to disable the color bar pattern or the character display on the menu.
䊶Shoot a known white object entirely in the area and push [DATA UP] button for approx. 1 second.
䊶The character AWB blinks on the screen when the AWB starts.
䊶The character AWB stops blinking when the AWB finishes, and the result is displayed for approx. 1 second.
6 2 White Balance
For white balance adjustment of this unit, ATW (Automatic Tracking White balance), AWB (Automatic
White Balance) and MANUAL (Manual white balance) adjustments are provided. Refer to the items “7.2
(3) WHT BAL (White Balance), 7. MODE SETTING BY THE ON SCREEN DISPLAY”, select the desired
mode.
IK-CT1CEN.indd12IK-CT1CEN.indd12 2008/02/1412:12:442008/02/1412:12:44

13
MeaningDisplay
AWB OK Automatic white balance adjustment finished correctly.
AWB NG
LEVEL LOW
Automatic white balance adjustment cannot be performed because the video level is
too low.
Adjust the video level by increasing the illumination or opening the lens iris.
AWB NG
LEVEL HIGH
Automatic white balance adjustment cannot be performed because the video level is
too high.
Adjust the video level by decreasing the illumination or closing the lens iris.
AWB NG
C. TEMP LOW
Automatic white balance adjustment cannot be performed because the color
temperature is too low.
Change the illumination or use a color temperature conversion filter.
AWB NG
C. TEMP HIGH
Automatic white balance adjustment cannot be performed because the color
temperature is too high.
Change the illumination or use the color temperature conversion filter.
AWB NG Automatic white balance adjustment cannot be performed for other reasons. Such as
no white area is included in an object, etc.
㽳MANUAL(Manual white balance)
䊶Set the MODE to MANUAL on the WHT BAL menu.
(Refer to the item “7.2 (3) WHT BAL (White Balance)”.)
䊶Shoot a known white object, set the white balance by adjusting the levels of R GAIN and B GAIN on the
menu, confirming with a monitor or a vector scope.
(Refer to the item “7.2 (3) (3.4) MANUAL mode”.)
IK-CT1CEN.indd13IK-CT1CEN.indd13 2008/02/1412:12:442008/02/1412:12:44

14
Six scene files (A, B, C, D, E, F) are available as user memories for this unit. These are chosen depending
on shooting conditions. By using the [FILE] button, the camera operation is changed immediately from the
currently selected Scene File to the next. (Refer to the item “7. MODE SETTING BY THE ON SCREEN
DISPLAY”.)
䊶While any menu is displayed, pressing the [FILE] button will display the menu settings for the next Scene File:
FILE A 㸢
㸢㸢
㸢FILE B 㸢
㸢㸢
㸢FILE C 㸢
㸢㸢
㸢FILE D 㸢
㸢㸢
㸢FILE E 㸢
㸢㸢 FILE F
䊶When the [FILE] button is pressed while the camera is in live image mode, the current scene file selection
䊶If the color bar pattern is displayed on the screen, press the [DISP] button to change the camera is
in live image mode.
at that time is displayed for approx. 3 seconds in the upper right corner of the screen. If the [FILE] button is
pressed again while the position is displayed, the scene file cycles as described above.
When the image is dark, change the gain (video gain) to get the desired video level. For gain adjustment
of the unit, AUTO (Automatic gain control), MANUAL (Manual), OFF (0 dB) modes are provided.
Select the mode on the GAIN menu. (Refer to the item “7.2 (2) GAIN (Video gain)”.)
㽲AUTO(Automatic gain control)
When the output is low, gain is automatically adjusted to a suitable video level.
The maximum value of gain is 20dB, and can be set from 0 to 20dB in 1dB steps. (Refer to the item
“7.2 (2) (2.2) AUTO mode”.)
Video level (LEVEL), peak average value ratio (PEAK/AVE), and measurement light area (AREA) is linked
to the setting on the automatic shutter. (Refer to the item “7.2 (1) (1.1) AUTO mode”.)
㽳MANUAL(Manual gain)
Gain adjustment is performed on the GAIN menu. The adjustment range is from 0 to 20dB in 1dB steps.
(Refer to the item “7.2 (2) (2.3) MANUAL mode”.)
㽴OFF
Gain is fixed at 0 dB.
6 3 Scene File
64Gain
IK-CT1CEN.indd14IK-CT1CEN.indd14 2008/02/1412:12:442008/02/1412:12:44

15
Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The
contents once set are memorized in the scene files (A, B, C, D, E ,F) selected, so if the power turns off, it
is unnecessary to set again when using the unit next time. When the setting is performed, select the menu
of the item to be set.
When the power turns on, the normal screen showing only the video signal appears. Change the output to
each screen (video signal output, color bar screen, Index menu, menus, and area menu) by using the [DISP],
[PAGE], [MENU UP], [MENU DOWN], [DATA UP], and [DATA DOWN] buttons.
* A menu is selected when pushing the [PAGE] button after moving the “㸢” on the screen by the [MENU
UP], [MENU DOWN] button while the Index menu is displayed.
7MODE SETTING BY THE ON SCREEN DISPLAY
7 1 Using the Menus
USER
AREA menu
DATA
UP/DOWN
D
A
B
C
E
DISP
POWER SW
ON
Video signal output
DISP
PAGE
PAGE
1.SHUTTER 2.GAIN 3.WHT BAL 4.PROCESS 5.MATRIX
Color bar screen
Menus
Index menu
DISP DISP
PAGE PAGE PAGE PAGE
PAGE PAGE
AUTO
MANU
NOAWB
OFF
OFF
ATW
MANU
GAMMA
AUTO
MANU
SS
PAGE
DISP
6.OPTION
RATE
BAUD
FREEZE/
DATA
UP/DOWN
DISP
EDIT
TITLE
IK-CT1CEN.indd15IK-CT1CEN.indd15 2008/02/1412:12:442008/02/1412:12:44

16
䊶Select the menu to change the setting by referring to the item “7.1 Using the Menus”.
䊶When the [MENU UP], [MENU DOWN] buttons are pushed, the “㸢” on the screen moves up and down.
Move the “㸢” to the item whose setting you wish to change.
1 SHUTTER䋨
䋨
Electronic shutter
䋩
The electronic shutter has three modes; AUTO, MANUAL, SS(Synchro. Scan).
Press the “Page” button to enter the Shutter Page. Move the “→” to “SHUTTER” by pushing [MENU UP],
[MENU DOWN] buttons. Select a mode from AUTO, MANUAL, and SS by pushing [DATA UP],
[DATA DOWN] buttons.
AUTO MANUAL SS
AUTO 䋺The exposure time is controlled automatically to obtain the video level set.
MANUAL 䋺It is possible to select the exposure time from eight speed settings; OFF (1/60s), 1/100s,
1/250s, 1/500s, 1/1000s, 1/2000s, 1/5000s, 1/10000s.
Note:
When setting a rapid shutter speed, sensitivity degrades according to the speed.
When a discharging light such as fluorescent lamp, etc. is used for the illumination,
the flicker may be large.
SS 䋺Shutter speed can be set by the horizontal scanning time (1H) unit.
7 2 Menus
Shutter mode AUTO, MANUAL, SS
Move up and down
by pushing
MENU UP,DOWN
Select the desired
value by pushing
DATA UP,DOWN
-- 1 SHUTTER --
MODE AUTO
LEVEL 0
PEAK AVE 05
MAX EXP. OFF
05
SPEED 1
AREA PRESET A
AREA DISPLAY OFF
IK-CT1CEN.indd16IK-CT1CEN.indd16 2008/02/1412:12:442008/02/1412:12:44

17
䋨
䋨䋨
䋨1䋮
䋮䋮
䋮1䋩
䋩䋩
䋩AUTO mode
(a) Changing MAX EXP. setting
Maximum exposure time setting in the automatic shutter
mode
[ OFF, 1FRM㨪128FRM ]
* Maximum exposure time is as below.
OFF...1/60s, 1FRM...1/30s, 128FRM...128/30s
long exposure
㽲Move the “㸢” to MAX EXP. by pushing [MENU UP], [MENU DOWN] buttons.
㽳Select the maximum exposure time by pushing [DATA UP], [DATA DOWN] buttons.
Note:
• More than 1FRM setting will be long exposure. Moving objects might show up blurred. This is not a
malfunction.
• White, red, green, or blue dots may occur on screen when the exposure time is long.
This is not a malfunction, just certain characteristics of the CCD becoming more visible.
Move up and down
by pushing
MENU UP,DOWN
Select the desired
value by pushing
DATA UP,DOWN
-- 1 SHUTTER --
MODE AUTO
LEVEL 0
PEAK AVE 05
MAX EXP. OFF
05
SPEED 1
AREA PRESET A
AREA DISPLAY OFF
(b) Changing LEVEL setting
Level adjustment in the automatic shutter mode
[ -100 㨪0 㨪㧗100 ]
(1dB step)
㽲Move the “㸢” to LEVEL by pushing [MENU UP], [MENU DOWN] buttons.
㽳Select the video level by pushing [DATA UP],[DATA DOWN] buttons.
The value increases by pushing [DATA UP]
䋭100 0 100
The value decreases by pushing [DATA DOWN]
Move up and down
by pushing
MENU UP,DOWN
Select the desired
value by pushing
DATA UP,DOWN
-- 1 SHUTTER --
MODE AUTO
LEVEL 0
PEAK AVE 05
MAX EXP. OFF
05
SPEED 1
AREA PRESET A
AREA DISPLAY OFF
IK-CT1CEN.indd17IK-CT1CEN.indd17 2008/02/1412:12:442008/02/1412:12:44

18
㩷䇭
(c) Changing PEAK/AVE setting
(d) Changing SPEED setting
Peak and average ratio adjustment in the automatic shutter
mode. (peak:average)
[ 00:10 only average ]
[ 10:00 only peak ]
* Pushing [ DATA UP ] button makes the peak ratio high.
* Pushing [ DATA DOWN ] button makes the average
Automatic shutter response speed adjustment
(1dB step)
* The bigger the number, the faster the response speed.
㽲Move the “㸢” to PEAK/AVE by pushing [MENU UP], [MENU DOWN] buttons.
㽳Select the peak and average ratio by pushing [DATA UP], [DATA DOWN] buttons.
㽲Move the “㸢” to SPEED by pushing [MENU UP], [MENU DOWN] buttons.
㽳Select the speed by pushing [DATA UP], [DATA DOWN] buttons.
Move up and down
by pushing
MENU UP,DOWN
Select the desired
value by pushing
DATA UP,DOWN
Move up and down
by pushing
MENU UP,DOWN
Select the desired
value by pushing
DATA UP,DOWN
-- 1 SHUTTER --
MODE AUTO
LEVEL 0
PEAK AVE 05
MAX EXP. OFF
05
SPEED 1
AREA PRESET A
AREA DISPLAY OFF
-- 1 SHUTTER --
MODE AUTO
LEVEL 0
PEAK AVE 05
MAX EXP. OFF
05
SPEED 1
AREA PRESET A
AREA DISPLAY OFF
ratio high.
IK-CT1CEN.indd18IK-CT1CEN.indd18 2008/02/1412:12:442008/02/1412:12:44

19
㩷䇭
䇼A䇽䇼B䇽䇼C䇽
䇼D䇽䇼E䇽䇼USER䇽
(e) Changing AREA setting
Automatic shutter zone area setting
[ A, B, C, D, E, USER ]
㽲Move the “㸢” to AREA by pushing [MENU UP], [MENU DOWN] buttons.
㽳Select the area by pushing [DATA UP], [DATA DOWN] buttons.
The picture area used is shown by the shading on the screen. The total area is divided into 64 parts.
Note:
These available picture areas are displayed by selecting ON for AREA DISPLAY.
Please select the best area by looking at the whole screen while making changes.
(User selectable for all
64 parts.)
Move up and down
by pushing
MENU UP,DOWN
Select the desired
value by pushing
DATA UP,DOWN
-- 1 SHUTTER --
MODE AUTO
LEVEL 0
PEAK AVE 05
MAX EXP. OFF
05
SPEED 1
AREA PRESET A
AREA DISPLAY OFF
IK-CT1CEN.indd19IK-CT1CEN.indd19 2008/02/1412:12:442008/02/1412:12:44

20
䌕
䃂
㩷䇭
㩷䇭
(f) Changing AREA DISPLAY / USER AREA
䋨
䋨䋨
䋨1䋮
䋮䋮
䋮2䋩
䋩䋩
䋩MANUAL mode
Displaying the available picture area in the automatic
shutter.
Editing the user area
Available picture area and the editing user area menu
are displayed by pushing [DATA UP], [DATA DOWN]
buttons.
Displaying the available picture area mode :
[A, B, C, D, E, U]
(Available picture area is displayed with a square frame.)
Key operation (for common)
DISP : Gets back the shutter page.
MANUAL mode setting
[ OFF, 1/100s, 1/250s, 1/500s, 1/1000s, 1/2000s,
1/5000s, 1/10000s ]
Displaying cursor (for user only)
Key operation (for user only)
MENU UP : Moves the cursor up for each cell.
MENU DOWN : Moves the cursor down for each cell.
DATA UP : Moves the cursor right for each cell.
DATA DOWN : Moves the cursor left for each cell.
PAGE : Switches the cursor ON/OFF.
㽲Move the “㸢” to AREA DISPLAY by pushing [MENU UP], [MENU DOWN] buttons.
㽳Display AREA DISPLAY screen by pushing [DATA UP], [DATA DOWN] buttons.
㽲Move the “㸢” to MANUAL by pushing [MENU UP], [MENU DOWN] buttons.
㽳Select the manual mode by pushing [DATA UP], [DATA DOWN] buttons.
Operation for AREA DISPLAY / USER AREA
Move up and down
by pushing
MENU UP,DOWN
Select the desired
value by pushing
DATA UP,DOWN
Move up and down
by pushing
MENU UP,DOWN
Select the desired
value by pushing
DATA UP,DOWN
-- 1 SHUTTER --
MODE AUTO
LEVEL 0
PEAK AVE 05
MAX EXP. OFF
05
SPEED 1
AREA PRESET A
AREA DISPLAY OFF
-- 1 SHUTTER --
MODE MANUAL
MANUAL 䋱䋯䋱䋰䋰䌳
IK-CT1CEN.indd20IK-CT1CEN.indd20 2008/02/1412:12:442008/02/1412:12:44