Toshiba IK-HD3D User manual

CAMERA CONTROL UNIT
IK-HD3D
INSTRUCTION MANUAL
U.S.A INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursu-
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
USER-INSTALLER CAUTION: Your authority to operate this FCC verified equipment could be voided if
you make changes or modifications not expressly approved by the party responsible for compliance to
Part 15 of the FCC Rules.
This manual is made from recycled paper.
For Customer Use
Enter below the Serial No.
which is located on the
bottom of the cabinet. Retain
this information for future ref-
erence.
Model No.: IK-HD3D
Serial No.:
Following information is only for EU-member states:
In residential areas this product may cause radio interference, therefore this product must
not be used in residential areas.
The use of the symbol indicates that this product may not be treated as household waste.
By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed information about the take-
back and recycling of this product, please contact your supplier where you purchased the
product or consult.

2
SAFETY PRECAUTIONS
Safety icons
This manual contains safety instructions that must be observed in order to avoid potential
hazards that could result in personal injuries, damage to your equipment, or loss of data.
These safety cautions have been classified according to the seriousness of the risk, and the
icons highlight these instructions as follows:
Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in
minor or moderate injury.
Indicates a potentially hazardous situation which, if not avoided, may result in
property damage.
Stop operation immediately if any abnormality or defect occurs.
Use during an abnormal condition; such as emitting smoke, burning odors,
damage from dropping, invasion of foreign objects, etc. may result in fire and/or
electric shock. Immediately disconnect the power source and contact your dealer.
Avoid installing in a shower room or a bathroom.
This may result in fire and/or electric shock.
Do not operate in places where the product may get wet.
This may result in fire and/or electric shock.
Do not repair, disassemble and/or modify by yourself.
This may result in fire and/or electric shock. Be always sure to contact your
dealer for internal repair, check and cleaning of the product.
Use the specified power supply.
Otherwise, fire or electrical shock may occur.
Do not place anything on top of the unit.
Foreign materials, such as metals or liquids into the product may result in fire
and/or electrical shock.
Do not put the product on an unstable, slanted on vibrating surface.
The product dropping or falling may cause serious injury.
Do not touch the product or any connection cables during a thunderstorm.
This may result in electrical shock.

3
Note the following instructions when installing.
s$ONOTCOVERTHEPRODUCTWITHANYMATERIAL
s$ONOTPLACETHEPRODUCTONANYCONFINED)NFLAMMABLEMATERIALSUCHASA
carpet or blanket.
s$ONOTPLACETHEPRODUCTINANARROWSPACEASTHISMAYCAUSEHEATTOBUILDUP
inside the product.
Failure to follow the above cautions may result in fire.
Do not place the product in direct sunshine and/or high temperature.
Temperature build up inside the product may result in fire.
Avoid placing in humid, smoky, vaporized or dusty places.
This may result in fire and/or electric shock.
Ask your dealer to perform a periodical check and internal cleaning
(approx. once every five years).
$USTINSIDETHEPRODUCTMAYRESULTINlRE&ORCHECKANDCLEANINGCOSTPLEASE
consult your dealer.
The following description is described the state that the suitable camera head is connected to this
camera control unit.
Do not point the lens directly at the sun and/or intensive light such as
direct sunlight, etc.
Focusing of the light may cause eye injury and/or fire.
Disclaimer
We disclaim any responsibility and shall not be responsible for any damages or losses incurred by
the user in any of the following cases:
1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether inten-
tional or accidental; use under extreme operating conditions.
2. Malfunction or non-function resulting in indirect, additional or consequential damages, including
but not limited to loss of expected income and suspension of business activities.
3. Incorrect use not in compliance with instructions in this instruction manual.
4. Malfunctions resulting from misconnection to other equipment.
5. Repairs or modifications made by the user or caused to be made by the user and carried out by
an unauthorized third party.
Notwithstanding the foregoing, Toshiba America Information Systems, Inc.’s liabilities shall not, in
any circumstances, exceed the purchase price of the product.
Copyright and Right of Portrait
There may be a conflict with the Copyright Law and other laws when, the customer, uses, displays,
distributes, or exhibits an image picked up by the camera without permission from the copyright
holder. Please also note that transfer of an image or file covered by copyright is restricted to use
within the scope permitted by the Copyright Law. You are solely responsible for complying with all
applicable copyright laws.

4
Protection of Personal Information
Images taken by the camera that reveal the likeness of an individual person may be considered
personal information. To disclose, exhibit or transmit those images over the internet or otherwise,
consent from such individual person may be required. You are solely responsible to obtain such
consent.
Limitation of Usage
The product is not designed for any “critical applications.” “Critical applications” means life support
systems, exhaust or smoke extraction applications, medical applications, commercial aviation,
mass transit applications, military applications, homeland security applications, nuclear facilities or
systems or any other applications where product failure could lead to injury to persons or loss of life
or catastrophic property damages. Accordingly, We disclaim any and all liability arising out of the
use of the product in any critical applications.
TABLE OF CONTENTS
1. CAUTIONS ON USE AND INSTALLATION...............................................................................................6
2. COMPONENTS..........................................................................................................................................6
3. ITEMS CONTROLLED BY THE SCREEN DISPLAY.................................................................................7
4. NAMES AND FUNCTIONS........................................................................................................................8
5. CONNECTION............................................................................................................................................9
5. 1 Standard Connection .........................................................................................................................9
5. 2 Cautions on Connection...................................................................................................................10
5. 3 Connector Pin Assignments.............................................................................................................10
6. OPERATION.............................................................................................................................................11
6. 1 Automatic Black Balance .................................................................................................................11
6. 2 White Balance..................................................................................................................................11
6. 3 Scene File........................................................................................................................................12
6. 4 Gain .................................................................................................................................................13
6. 5 Shading Correction ..........................................................................................................................14
6. 6 Switching of Video Signal Output.....................................................................................................14
7. MODE SETTING BY ON SCREEN DISPLAY..........................................................................................15
7. 1 Using the Menus..............................................................................................................................15
7. 2 Menus ..............................................................................................................................................16
( 1 ) SHUTTER (Electronic shutter).........................................................................................................16
(1. 1) Changing the setting in AUTO mode .....................................................................................17
(1. 2) Changing the setting in MANUAL mode ................................................................................19
(1. 3) Changing the setting in SS (Synchro. Scan) mode................................................................19
( 2 ) GAIN (Video gain)............................................................................................................................20
(2. 1) Changing maximum gain in AUTO (AGC: Automatic gain control) mode ..............................20
(2. 2) Changing gain in MANUAL mode ..........................................................................................20
( 3 ) WHT BAL (White balance)...............................................................................................................21
(3. 1) Changing the setting in AWB (Automatic White Balance) mode ...........................................21
(3. 2) Changing gain in MANUAL mode ..........................................................................................22

5
( 4 ) PROCESS1 .....................................................................................................................................23
(4. 1) Changing gamma correction ON/OFF...................................................................................23
(4. 2) Changing gamma correction level .........................................................................................23
(4. 3) Changing black gamma correction level ................................................................................23
(4. 4) Changing pedestal.................................................................................................................24
(4. 5) Change of white clip ..............................................................................................................24
( 5 ) PROCESS2 .....................................................................................................................................25
(5. 1) Changing detail (outline) gain................................................................................................25
(5. 2) Change of detail boost frequency..........................................................................................25
(5. 3) Change of horizontal and vertical detail balance...................................................................25
 #HANGING$.2$IGITAL.OISE2EDUCTION..............................................................................25
( 6 ) PROCESS3 .....................................................................................................................................26
(6. 1) Changing matrix color correction ON/OFF ...........................................................................26
(6. 2) Selection of matrix correction color........................................................................................26
(6. 3) Changing MATRIX setting......................................................................................................26
(6. 4) Change of chroma gain .........................................................................................................26
( 7 ) SYNC...............................................................................................................................................27
(7. 1) INT screen .............................................................................................................................27
(7. 2) Changing EXT. setting ...........................................................................................................27
( 8 ) OPTION...........................................................................................................................................28
(8. 1) Changing shading correction mode.......................................................................................28
(8. 2) Changing manual shading correction mode ..........................................................................28
(8. 3) Changing detail signal output ................................................................................................28
(8. 4) Change of vertical inversion setting .......................................................................................29
(8. 5) Change of horizontal inversion setting...................................................................................29
(8. 6) Switching of inversion mode display ......................................................................................29
(8. 7) Change of binning setting......................................................................................................29
(8. 8) Change of monitor receiver types..........................................................................................29
(8. 9) Change of I/P mode...............................................................................................................29
(8. 10) Changing RS-232C baud rate .............................................................................................29
( 9 ) Setting USER area ..........................................................................................................................30
( 10 ) Returning to factory settings..........................................................................................................31
7. 3 External Sync...................................................................................................................................31
7. 4 Synchro. Scan Operation .................................................................................................................31
8. BEFORE MAKING SERVICE CALL........................................................................................................32
9. SPECIFICATIONS....................................................................................................................................33
10. EXTERNAL APPEARANCE DIAGRAM ................................................................................................34

6
COMPONENTS2.
(1) Camera Control Unit...................................................................................................................... 1
(2) Accessories
(a) Instruction manual .................................................................................................................. 1
CAUTIONS ON USE AND INSTALLATION1.
s(ANDLINGTHEUNIT
$O NOT DROP JOLT OR VIBRATE AS THIS MAY RESULT IN
damage to the unit and may cause problems.Treat the
camera cables carefully to prevent cable problems,
such as breaks in the cable and loose connections.
s)NSTALLTHECAMERAINALOCATIONFREEFROMNOISE
If the camera or the cables are located near power
utility lines or a TV, etc. undesirable noise may appear
on the screen. In such a case, try to change the
location of the camera or the cable wiring.
s/PERATINGAMBIENTTEMPERATUREANDHUMIDITY
$ONOTUSETHECAMERAINPLACESWHERETEMPERATURE
and humidity exceed the specifications. Picture quality
will deteriorate and internal parts may be damaged.
Be particularly careful when using in places exposed
to direct sunlight. When shooting in hot environments,
depending on the conditions of the object and the
camera (for example when the gain is increased),
noise in the form of vertical strips or white dots may
occur. This is not a malfunction.
s7HENNOTUSINGTHECAMERAFOREXTENDEDPERIODS
of time.
Switch the control unit off and disconnect the power
supply.
s!VOIDUSINGORSTORINGTHECAMERAINTHEFOLLOWING
places:
Places filled with highly flammable and corrosive gas.
Places near gasoline, benzene, or paint thinner.
Places subject to strong vibration.
Places containing chemicals (such as pesticides),
rubber or vinyl products for extended periods of time.
s4HISPRODUCTISFORINDOORUSEONLY
The following descriptions are for a camera head
h)+($(vh)+(2(vCONNECTEDTOTHISCAMERACONTROL
unit.
s$ONOTSHOOTINTENSELIGHT
If strong light is entered, vertical stripes or traverse
bands may appear on the screen but this is not a
failure.
s-OIRE
A moire pattern is an interference pattern generated
when two repetitive line patterns overlap. This is not a
malfunction. Eliminating the repetitive line patterns, or
aligning the two patterns, will eliminate the moire.
s(ANDLINGOFTHECAMERAHEADANDPROTECTIONCAP
Keep the camera head and protection cap away from
children as they may pose a choking hazard. Because
the protection cap protects the image sensing plane
when the lens is removed from the camera head, do
not discard the protection cap.
s7HENCLEANINGTHECAMERA
Unplug the power source before cleaning. Clean
WITH A SOFT DRY CLOTH ONLY $O NOT USE CHEMICALS OR
chemically treated cloths. Chemicals may damage
coatings and printed letters. When cleaning the lens,
use lens cleaning paper.
s)NSTALLATIONWITHOUTATRIPOD
Before installing the camera head, make sure that the
location can withstand the total weight of the camera
head.
If this is not the case, reinforce the area to prevent the
unit from dropping, which may result in damage to the
unit or personal injury.

7
ITEMS CONTROLLED BY THE SCREEN DISPLAY3.
Item Available selections Preset value
(Factory setting)
Electronic shutter
-/$% AUTO, MANUAL, SS MANUAL
AUTO level -100 – 0 – 100 0
AUTO peak/average 00 : 10 – 05 : 05 – 10 : 00 05 : 05
AUTO response speed 1 – 10 – 20 10
AUTO area
02%3%4!02%3%4"02%3%4#02%3%4$02%3%4%
USER (USER area is possible to set in 64 zones)
PRESET A
Maximum AUTO shutter
speed
1/200s, 1/250s, 1/300s, 1/350s, 1/400s, 1/450s, 1/500s,
1/550s, 1/600s, 1/700s, 1/800s, 1/900s, 1/1000s,
1/1200s, 1/1500s, 1/2000s, 1/4000s, OFF
OFF
MANUAL shutter speed OFF, 1/100s, 1/125s, 1/250s, 1/500s, 1/1000s, 1/2000s,
1/3000s, 1/4000s, 1/5000s, 1/10000s OFF
Syncro. scan 1/1125H – 1122/1125H, OFF OFF
Gain
-/$% AUTO, MANUAL, OFF OFF
AUTO maximum gain 0dB to 20dB 20dB
MANUAL gain -3dB to 20dB 0dB
White balance
-/$% AWB, MANUAL AWB
Color temperature 3200K, 5600K 3200K
AWB R PAINT -10 – 0 – 10 0
AWB B PAINT -10 – 0 – 10 0
AWB area
02%3%4!02%3%4"02%3%4#02%3%4$02%3%4%
USER (USER area is possible to set in 64 zones)
PRESET A
MANUAL R GAIN -100 – 0 – 100 0
MANUAL B GAIN -100 – 0 – 100 0
Gamma correction ON, OFF ON
Gamma correction level -10 – 0 – 10 0
Black gamma correction level LOW, NORMAL, HIGH NORMAL
Master pedestal -200 – 0 – 200 0
Red pedestal -100 – 0 – 100 0
Blue pedestal -100 – 0 – 100 0
White clip 100% − 109% 109%
$ETAILGAIN 0 − 10 − 31 10
$ETAILBOOSTFREQUENCY 1 − 10 − 16 10
HV balance 8/16 − 16/16 − 24/16 (ratio of V/H) 16/16
$IGITALNOISEREDUCTION$.2 ON, OFF OFF
Matrix
Correction ON/OFF ON, OFF ON
Selection of correction color R, R-Ye, Ye, Ye-G, G, G-Cy, Cy, Cy-B, B, B-Mg, Mg, Mg-R R
Phase -15 – 0 – 15 0
Gain -15 – 0 – 15 0
Chroma gain -31 − 0 − 31 0
Ext. Sync H phase adjustment -650 – 0 – 650 0
Shading correction mode SET, MANUAL, OFF OFF
Manual shading correction -128 – 0 – 127 0
$ETAILSIGNALOUTPUT ON, OFF OFF
Vertical inversion ON, OFF OFF
Horizontal inversion ON, OFF OFF
Inversion mode display switch ON, OFF OFF
Binning ON, OFF OFF
Monitor PC, TV PC
I/P mode 1080p, 1080i 1080p
RS-232C baud rate 9600bps, 19200bps 9600bps

8
NAMES AND FUNCTIONS4.
3
4
2
1
12345
8796
2
10
18
1
9
17
3
11
19
4
12
20
5
13
21
6
14
22
7
15
23
8
16
24
Camera cable
for “IK-HD3H” or
“IK-HR3H” terminal
POWER switch
POWER LED
FILE button
GAIN button
DISP button
PAGE button
MENU UP
(SHD) button
MENU DOWN
button
DATA U P
(AWB) button
DATA DOWN
(ABB) button
DC IN 12V terminal
REMOTE terminal
EXT. SYNC terminal
SYNC OUT terminal
DVI-D terminal
KEY LOCK switch
FORMAT switch
[Front]
[Rear]
/#AMERACABLEFORh)+($(v
or “IK-HR3H” terminal
7HERETHECAMERACABLEFORh)+($(vORh)+(2(vISCONNECTED
00/7%2,%$ Illuminates to indicate the unit is powered on.
1POWER switch Turns power on or off.
2FILE button To switch the scene files.
3GAIN button To change the gain mode.
4$)30BUTTON Changes the display mode.
5PAGE button To switch and select menus.
6-%.5503($BUTTON To select the function to be confirmed or changed on the menu.
(Also used when performing auto shading correction.)
7-%.5$/7.BUTTON To select the function to be confirmed or changed on the menu.
8$!4!50!7"BUTTON 4OCHANGETHEVALUEOFTHEFUNCTIONSELECTEDBYTHE-%.550$/7.BUTTON
(Also used when performing an AWB.)
9$!4!$/7.!""BUTTON 4OCHANGETHEVALUEOFTHEFUNCTIONSELECTEDBYTHE-%.550$/7.BUTTON
(Also used when performing an ABB.)

9
:$#).6TERMINAL !CCEPTSA$#POWERINPUT6
;REMOTE terminal To connect to a RS-232C device for remote control function.
<EXT. SYNC terminal Used when the camera output signal is synchronized to an external signal.
(BNC connector)
=SYNC OUT terminal Output terminal for synchronization signal. (BNC connector)
>$6)$TERMINAL $6)$OUTPUTTERMINAL
?KEY LOCK switch Enables/disables buttons 2to 9.
@FORMAT switch Switches between 59.94Hz and 50Hz.
CONNECTION5.
Standard Connection5. 1
DC power supply
(option)
Lens
(option)
Camera
Camera
Head
Control unit
Camera Cable
for IK-HD3D
䠄option䠅
DVI monitor
DVI-D TV
(Commercially available)
DC IN 12V
DVI-D
DVI-D Cable
(Commercially
available)
IK-HD3D
IK-HD3H or
IK-HR3H (Scheduled to be available
in September, 2013)
(option)

10
Cautions on Connection5. 2
s7HENCONNECTING THECAMERACABLESBE SURETOTURNOFFTHE CAMERACONTROLUNITAND ANYOTHEREQUIPMENT
connected to it.
s&OR$#POWERSUPPLYCONNECTINGTO$#).6TERMINALUSECLASS))$#POWERSUPPLYAPPROVEDACCORDING
to EN60950-1 in Europe. or use UL listed and/or CSA approved ungrounded type AC adaptor with the
specifications described below in U.S.A. or Canada.
0OWERSUPPLYVOLTAGE 6$#
Current rating : More than 1.5A
Ripple voltage : Less than 50 mV (p–p)
Connector : HR10A–7P–4S by HIROSE electronics Co. Ltd
Pins 1, 2 : 12V
0INS'.$
s)FTHESECURINGSCREWONTHECONNECTOROFTHECAMERACABLELOOSENSNOISEMAYAPPEARONTHESCREEN"ESURE
to tighten the connector completely.
s/NLYUSETHESPECIlCOPTIONALCAMERAHEADSWITHTHISCAMERACONTROLLER
The use of any other camera heads may cause damage to the control unit and camera head.
s4HEVIDEOSIGNALOUTPUTOFTHISCAMERACONTROLUNITHASNOFUNCTIONFORAUTOMATICALLYSELECTINGOUTPUTACCORDING
TOTHERESOLUTIONOF$6)MONITOR464HEREFOREBESURETOSWITCHTHEOUTPUTMODEOFTHISCAMERACONTROLUNIT
according to the monitor’s resolution as no image will be displayed on the monitor if the camera output mode
and the monitor input mode do not match. For switching, refer to the item 6.6 “Switching of Video Signal
Output”.
s$6)STANDARD
4HE$6)DIGITALVISUALINTERFACEISTHECONNECTIONINTERFACESTANDARDFORmATPANELDISPLAY&0$SUCHAS,#$
DISPLAYS4HEREARETHREETYPESOF$6)CONNECTORSNAMELY$6))FORBOTHDIGITALANALOG$6)$EXCLUSIVELYFOR
DIGITALAND$6)!EXCLUSIVELYFORANALOG5SEACOMMERCIALLYAVAILABLE$6)$CABLEFORTHISCAMERACONTROLUNIT
Connector Pin Assignments5. 3
/NTHEREARPANEL OF THE CAMERACONTROLUNIT$#). 6 TERMINALUSEDFORBASICCONNECTIONAND2%-/4% %84
39.#39.#/54AND$6)$TERMINALAREPROVIDED#ONNECTCABLESDEPENDINGONYOURNECESSITY
3
4
2
1
12345
8796
2
10
18
1
9
17
3
11
19
4
12
20
5
13
21
6
14
22
7
15
23
8
16
24
$#).6TERMINAL REMOTE terminal $6)$TERMINAL
1 +12V 1 NC 1 $ATA 13 NC
2 +12V 2 48$ 2$ATA 14 +5V
3 '.$ 328$ 3$ATA3HIELD'.$ 15 '.$
4 '.$ 4 NC 4 NC 16 (OT0LUG$ETECT
5'.$ 5NC 17$ATA
6 NC 6 NC 18 $ATA
7 NC 7 NC 19 $ATA3HIELD'.$
8 NC 8 NC 20 NC
9NC 9$ATA 21 NC
10 $ATA 22 #LOCK3HIELD'.$
11 $ATA3HIELD'.$ 23 Clock+
12 NC 24 Clock-

11
OPERATION6.
A camera head needs to be connected to this camera control unit from this section on.
/Refer to the item “5. CONNECTION”, connect the equipment correctly.
0Turn on the connected equipment and the camera.
1When using the camera for the first time and when replacing the camera head, be sure to perform the ABB
adjustment, refer to the item “6.1 Automatic Black Balance”.
2Aim the lens at the object, adjust the lens iris adjustment, focus adjustment, etc.
3Refer to the item “6.2 White Balance”, make the adjustment.
42EFERTOTHEITEMSh3CENE&ILE'AIN-/$%3%44).'"94(%/.3#2%%.$)30,!9vSELECTTHE
necessary items.
Automatic Black Balance6. 1
Black balance adjustment is necessary to get the correct black picture level.
s#LOSETHELENSIRIS
s)FTHECOLORBARPATTERNISDISPLAYEDONTHESCREENORIFTHEINDEXMENUMENUISDISPLAYEDPRESSTHE;$)30=BUTTONTO
disable the color bar pattern or the character display.
s(OLDTHE;$!4!$/7.=BUTTONFORAPPROXSECOND
s7HENTHEBLACKBALANCEADJUSTMENTOPERATIONSTARTSTHECHARACTER!""BLINKSONTHESCREEN
s7HENTHEBLACKBALANCEADJUSTMENTOPERATIONlNISHESTHECHARACTER!""STOPSBLINKINGANDTHERESULTAPPEARSFOR
approx. 1 second.
Display Meaning
ABB OK Automatic black balance adjustment finished correctly.
ABB NG
CLOSE LENS
Automatic black balance adjustment cannot be performed because the lens iris is open. Close
the lens iris.
ABB NG Automatic black balance adjustment cannot be performed.
Operate the automatic black balance again.
7HITE"ALANCE6. 2
For white balance adjustment of this unit, AWB (Automatic White Balance) and MANUAL (Manual white balance)
ADJUSTMENTSAREPROVIDED2EFERTOTHEITEMSh7(4"!,7HITE"ALANCE-/$%3%44).'"94(%/.
3#2%%.$)30,!9vSELECTTHEDESIREDMODE
!7"
!UTOMATIC7HITE"ALANCE
MANUAL
-ANUAL7HITE"ALANCE
Outline Adjust white balance by displaying a white object
inside the area set by AWB menu and holding the
;$!4!50=BUTTONFORAPPROXSECOND
Adjust the white balance manually using the WHT
BAL menu while shooting a white object.
Features Automatically adjusts red and blue balance based
on green for the object in the designated area .
White balance can be set manually.
Note When no white object exits in the designated area
or lighting is too blight or too dark, AWB NG is
displayed and automatic white balance adjustment
can not be performed.
Adjustment is performed by confirming with a
monitor etc.

12
/AWB (Automatic white balance)
s3ETTHE-/$%TO!7"ONTHE7(4"!,MENU
Perform the C.TEMP (color temperature conversion) setting, if necessary.
(Refer to the item “7.2 (3) WHT BAL (White Balance)”.)
3200K : Appropriate for indoor shooting.
5600K : Appropriate for outdoor shooting.
s)FTHECOLORBARPATTERNISDISPLAYEDONTHESCREENORIFTHEINDEXMENUMENUISDISPLAYEDPRESSTHE;$)30=BUTTON
to disable the color bar pattern or the character display on the menu.
s3HOOT A KNOWN WHITE OBJECT ENTIRELY IN THE AREA SET BY THE !7" MENU REFER TO THE ITEMh   D
#ONlRMINGTHECONTENTSOFTHEZONEAREASELECTEDBY!7"vANDPUSH;$!4!50=BUTTONFORAPPROXSECOND
s4HECHARACTER!7"BLINKSONTHESCREENWHENTHE!7"STARTS
s4HECHARACTER!7"STOPSBLINKINGWHENTHE!7"lNISHESANDTHERESULTISDISPLAYEDFORAPPROXSECOND
Display Meaning
!7"/+ Automatic white balance adjustment finished correctly.
!7".'
,%6%,,/7
Automatic white balance adjustment cannot be performed because the video level is too low.
Adjust the video level by increasing the illumination or opening the lens iris.
!7".'
LEVEL HIGH
Automatic white balance adjustment cannot be performed because the video level is too high.
Adjust the video level by decreasing the illumination or closing the lens iris.
!7".'
#4%-0,/7
Automatic white balance adjustment cannot be performed because the color temperature is
too low.
If the C.TEMP is set to 5600K, set to 3200K.
If the message appears with the C.TEMP set to 3200K, change the illumination or use a color
temperature conversion filter.
!7".'
C. TEMP HIGH
Automatic white balance adjustment cannot be performed because the color temperature is
too high.
If the C.TEMP is set to 3200K, set to 5600K.
If the message appears with the C.TEMP set to 5600K, change the illumination or use the color
temperature convearsion filter.
!7".' Automatic white balance adjustment cannot be performed for other reasons. Such as no white
area is included in an object, etc.
0MANUAL (Manual white balance)
s3ETTHE-/$%TO-!.5!,ONTHE7(4"!,MENU
(Refer to the item “7.2 (3) WHT BAL (White Balance)”.)
s3HOOTAKNOWNWHITEOBJECTSETTHEWHITEBALANCEBYADJUSTINGTHELEVELSOF2'!).AND"'!).ONTHEMENU
confirming with a monitor or a vector scope.
(Refer to the item “7.2 (3) (3.2) Changing gain in MANUAL mode”.)
Scene File6. 3
&IVESCENElLES!"#$%AREAVAILABLEASUSERMEMORIESFORTHISUNIT4HESEARECHOSENDEPENDINGONSHOOTING
CONDITIONS"Y USING THE;&),%= BUTTONTHE CAMERAOPERATION ISCHANGEDIMMEDIATELY FROM THECURRENTLY SELECTED
3CENE&ILETOTHENEXT2EFERTOTHEITEMh-/$%3%44).'"94(%/.3#2%%.$)30,!9v
s7HILEANYMENUISDISPLAYEDPRESSINGTHE;&),%=BUTTONWILLDISPLAYTHEMENUSETTINGSFORTHENEXT3CENE&ILE
FILE A 䊲
䊲䊲
䊲FILE B 䊲
䊲䊲
䊲FILE C 䊲
䊲䊲
䊲FILE D 䊲
䊲䊲
䊲FILE E
s)FTHECOLORBARPATTERNISDISPLAYEDONTHESCREENPRESSTHE;$)30=BUTTONTOSWITCHTOTHEVIDEOSIGNALSCREEN
s7HENTHE;&),%=BUTTONISPRESSEDWHILETHEVIDEOSIGNALSCREENISDISPLAYEDTHECURRENTSCENElLESELECTIONATTHAT
TIMEISDISPLAYEDFORAPPROXSECONDSINTHEUPPERRIGHTCORNEROFTHESCREEN)FTHE;&),%=BUTTONISPRESSEDAGAIN
while the position is displayed, the scene file cycles as described above.
Note:
4HESCENElLEDOESNOTINCLUDETHEDATASETINh)0-/$%vh"!5$2!4%vWITHINTHEh/04)/.vMENU
Refer to the item “7.2 (8) Menus” for the contents that can be set in OPTION.

13
Gain6. 4
When the image is dark even if the lens iris is open, change the gain (video gain) to get the desired video level.
For gain adjustment of the unit, AUTO (Automatic gain control), MANUAL (Manual gain control), OFF (0 dB) modes
are provided. Select the mode on the GAIN menu. (Refer to the item “7.2 (2) GAIN (Video gain)”.)
/AUTO (Automatic gain control)
When the output is low, gain is automatically adjusted to a suitable video level.
The maximum value of gain is 20dB, and can be set from 0 to 18dB in 1dB steps. (Refer to the item “7.2 (2) (2.1)
Changing the maximum gain in AUTO (Automatic gain control) mode”.)
Video level (LEVEL), peak average value ratio (PEAK/AVE), measurement light area (AREA), and response
SPEED30%%$ARELINKEDTOTHESETTINGONTHEAUTOMATICSHUTTER2EFERTOTHEITEMh#HANGINGTHE
setting in AUTO mode”.)
0MANUAL (Manual gain)
Gain adjustment is performed on the GAIN menu. The adjustment range is from -3 to 20dB in 1dB steps.
(Refer to the item “7.2 (2) (2.2) Changing gain in MANUAL mode”.)
1OFF
Gain is fixed at 0 dB.
Gain button
/ )FTHE;'!).=BUTTONISPRESSEDTHECURRENTGAINSETTINGISDISPLAYEDFORAPPROXSECONDS
GAIN menu : OFF →GAIN OFF
SS : AUTO →GAIN AUTO
AUTO : MANUAL  dB →GAIN dB
“ ” shows the setting gain in MANUAL mode.
0)FTHE;'!).=BUTTONISPRESSEDAGAINWHILETHECURRENTSETTINGMODEISDISPLAYEDTHEGAINMODECANBECHANGED
GAIN of MAX GAIN in AUTO mode and MANUAL mode can not be changed.
OFF 䊲
䊲䊲
䊲AUTO 䊲
䊲䊲
䊲MANUAL
Note:
White, red, green, or blue dots may occur when the gain is increased. This is not a malfunction, just certain
characteristics of the CMOS sensor becoming more visible.

14
Shading Correction6. 5
$UETOTHELENSUSEDORTHEENVIRONMENTALCONDITIONCOLORSHADINGMAYOCCURATTHEUPPERANDLOWEREDGEOFTHE
screen. If this happens, the shading correction function can be used to decrease the amount of color shading. For
shading correction of the unit, SET (Automatic shading correction), MANUAL (Manual shading correction), and OFF
(no shading correction) modes are provided. Select the mode on the OPTION menu. (Refer to the item “7.2 (8) (8.1)
Changing shading correction mode”.)
/SET (Auto shading)
s)FTHECOLORBARPATTERNISDISPLAYEDONTHESCREENORIFTHEINDEXMENUMENUISDISPLAYEDPRESSTHE;$)30=BUTTON
to remove them from the screen.
s0USHTHE;-%.550=BUTTONFORAPPROXSECOND
s7HENTHEAUTOMATICSHADINGCORRECTIONOPERATIONSTARTSTHECHARACTER3($BLINKSONTHESCREEN
s7HENTHEAUTOMATICSHADINGCORRECTIONOPERATIONTERMINATESTHECHARACTER3($ENDSBLINKINGANDTHERESULTIS
displayed for approx. 1 second.
Display Meaning
SHD OK Automatic shading correction operation finished correctly.
SHD OK
LIMIT
Automatic shading correction operation finished, however, the correction necessary exceeds
the camera’s range so the maximum possible value is applied.
SHD NG
,%6%,,/7
Automatic shading correction cannot be performed because the video level is too low. Adjust
the video level by increasing the illumination or opening the lens iris.
SHD NG
LEVEL HIGH
Automatic shading correction cannot be performed because the video level is too high. Adjust
the video level by decreasing the illumination or closing the lens iris.
0MANUAL (Manual Shading)
Perform the correction amount setting on the OPTION menu, confirming with a monitor or a vector scope.
(Refer to the “7.2 (8) (8.2) Changing manual shading correction mode”.)
1OFF
The status is no shading correction.
* Shading correction is only effective when the lens iris and zoom ratio is fixed. Use the unit with SHADING
OFF for variable lens conditions.
Note:
Implement shading correction after white balance adjustment by shooting a white object that fills the screen in
THEPROPERVIDEOLEVEL)+($(#-/3CAMERAHEADNEEDSADJUSTMENTBECAUSEITUSESPRISMTOSPLITLIGHTAND
white shading may appear depending on the entrance angle against the lens exit pupil and prism.
IK-HR3H (Scheduled to be available in September, 2013) will not have this function because it does not need
adjustment described above.
Switching of Video Signal Output6. 6
/Switching of I/P modes
The image output can be changed between “1080p” and “1080i” by turning on the power supply while pushing the
;$!4!50=OR;$!4!$/7.=BUTTON
s4URNONTHEPOWERSUPPLYWHILEPUSHINGTHE;$!4!50=BUTTON4HEIMAGEOUTPUTBECOMEShPvANDhPv
is displayed on the monitor screen.
s4URN ON THE POWER SUPPLY WHILE PUSHING THE ;$!4! $/7.= BUTTON 4HE IMAGE OUTPUT BECOMEShIv AND
“1080i” is displayed on the monitor screen.
0Switching of vertical frequency
Turn the FORMAT switch to the “59.94” position for switching to “59.94Hz”.
Turn the FORMAT switch to the “50” position for switching to “50Hz”.
2EFERTOTHEITEMh.!-%3!.$&5.#4)/.3@FORMAT switch”.)

15
MODE SETTING BY ON SCREEN DISPLAY7.
Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The contents
ONCESETAREMEMORIZEDINTHESCENElLES!"#$%SELECTEDSOIFTHEPOWERTURNSOFFITISUNNECESSARYTOSET
again when using the unit next time. When the setting is performed, select the menu of the item to be set.
Note:
$ISPLAYEDTEXTSWHILEPRESSINGTHE SCREENMENUAUTO WHITEBALANCE!7"OROTHERMENUSAREOUTPUTTOTHE
taken videos. These texts on the videos are not removable after the videos are recorded. Therefore, be careful
when you operate the screen menu, AWB and other menus.
Using the Menus7. 1
When the power turns on, the normal screen showing only the video signal appears. Change the output to each
SCREENVIDEO SIGNALOUTPUTCOLORBARSCREEN)NDEXMENUMENUSANDAREAMENUBYUSINGTHE;$)30=;0!'%=
;-%.550=AND;-%.5$/7.=BUTTONS
!MENUISSELECTEDWHENPUSHINGTHE;0!'%=BUTTONAFTERMOVINGTHEh vTHESCREENBYTHE;-%.550=;-%.5
$/7.=BUTTONWHILETHE)NDEXMENUISDISPLAYED
USER
USER
Area menu
DATA
UP/DOWN
DATA
UP/DOWN
The screen is changed to the area screen by
selecting AUTO in the 1.SHUTTER menu and
AWB in the 3.WHT BAL menu in the setting
screen For more details, refer to the item "7.2
Menus".
D
A
B
C
E
DISP DISP
D
A
B
C
E
Area menu
POWER SW
ON
Video signal output
DISP
PAGE
PAGE
1.SHUTTER 2.GAIN 3.WHT BAL
Color bar screen
Menus
Index menu
DISP DISP
PAGE PAGE PAGE PAGE
PAGE PAGE
AUTO AWB
OFF
INT
EXT.
GAMMA
ON
GAMMA
OFF
AUTO
SS
PAGE
DISP
8.OPTION
PAGE
7.SYNC
MATRIX
ON
MATRIX
OFF
PAGE
6.PROCESS34.PROCESS1 5.PROCESS2
MANUAL MANUAL MANUAL
SHADING
OFF
SET
MANUAL

16
Menus7. 2
s3ELECTTHEMENUTOCHANGETHESETTINGBYREFERRINGTOTHEITEMh5SINGTHE-ENUSv
s7HENTHE;-%.550=;-%.5$/7.=BUTTONSAREPUSHEDTHEh ” on the screen moves up and down.
Move the “ ” to the item whose setting you wish to change.
SHUTTER (Electronic shutter)( 1 )
The electronic shutter has three modes; AUTO, MANUAL, SS(Synchro. Scan).
0RESSTHEh0AGEvBUTTONTOENTERTHE3HUTTER0AGE5SETHEh$ATA5P$OWNvBUTTONSTOSELECTTHE3HUTTER-ODE
MANUAL SSAUTO
AUTO : The exposure time is controlled automatically to obtain the video level set.
MANUAL : It is possible to select the exposure time from eleven speed settings; OFF (at 1/60s: 59.94Hz setting
and 1/50s: 50Hz setting), 1/100s, 1/125s, 1/250s, 1/500s, 1/1000s, 1/2000s, 1/3000s, 1/4000s,
1/5000s, 1/10000s.
SS : Shutter speed can be set by the horizontal scanning time (1H) unit.
Notes:
s)FTHESHUTTERSPEEDISINCREASEDTHESENSITIVITYISDECREASEDACCORDINGTOTHESPEED&LICKERMAYBELARGEUNDER
discharge lamp lighting such as fluorescent tubes.
s)F A FASTMOVING OBJECT IS SHOT ITS IMAGE MAY BE DISTORTED OR BLURRED (ORIZONTAL LIGHTANDDARK STRIPES MAY
appear on the screen under discharge lamp lighting such as fluorescent tubes. A light and dark difference may
appear on the screen according to the light emitting timing of flash or strobe.These phenomena are caused due
to rolling shutter system, not failures.
s7HEN THE SHUTTER SPEED IS SET TO HIGH THE HUE MAY CHANGE ACCORDING TO THE SHOOTING CONDITIONS AND THE
object.

17
Changing the setting in AUTO mode(1. 1)
Shutter mode AUTO, MANUAL, SS
Video level adjustment -100 to 100
Peak and average ratio adjustment 00 10 to 10 00
-- 1 SHUTTER -- (FILE A)
Automatic shutter response speed adjustment 1 to 20
MODE AUTO
LEVEL 0
Automatic shutter area selection
PEAK AVE 05 05
PRESET A, PRESET B, PRESET C, PRESET D, PRESET E,
USER
SPEED 10
AREA PRESET A
AREA DISPLAY OFF
MAX SHUT OFF
<MODE = AUTO>
Move up and down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
Automatic shutter area display selection
Automatic shutter maximum speed setting
(a) Changing the video level in the automatic shutter mode
Move the “/I vTO,%6%,BYPUSHINGTHE;-%.550=;-%.5$/7.=BUTTONS
3ELECTTHEVIDEOLEVELBYPUSHINGTHE;$!4!50=;$!4!$/7.=BUTTONS0I
;$!4!50= The value increases by pushing
-100 0 100
The value decreases by pushing ;$!4!$/7.=
(b) Changing the automatic shutter detection (ratio between peak and average value)
Move the “/I vTO0%!+!6%BYPUSHINGTHE;-%.550=;-%.5$/7.=BUTTONS
3ELECTTHERATIOBETWEENPEAKANDAVERAGEVALUEBYPUSHINGTHE;$!4!50=;$!4!$/7.=BUTTONS0I
(Peak: Average) 4HEPEAKVALUEINCREASESBYPUSHING;$!4!50=
00:05 05:05 10:00
The peak value decreases by pushing ;$!4!$/7.=
(c) Changing the automatic shutter response speed
Move the “/I vTO30%%$BYPUSHINGTHE;-%.550=;-%.5$/7.=BUTTONS
3ELECTTHERESPONSESPEEDBYPUSHINGTHE;$!4!50=;$!4!$/7.=BUTTONS0I
;$!4!50= The response speed becomes faster by pushing
1 10 20
The response speed becomes slower by pushing ;$!4!$/7.=

18
(d) Changing the automatic shutter response speed
Move the “/I vTO!2%!BYPUSHINGTHE;-%.550=;-%.5$/7.=BUTTONS
3ELECTTHEMEASUREMENTLIGHTAREABYPUSHINGTHE;$!4!50=;$!4!$/7.=BUTTONS0I
[DATA UP]
PRESET A PRESET B PRESET C PRESET D PRESET E USER
[DATA DOWN]
The available picture area is shown by the shading correction on the screen that is parted in 64.
PRESET A PRESET B PRESET DPRESET C
PRESET E USER
Custom
Selection
(e) Confirming the contents of the measurement light area selected by the automatic shutter
Move the “/I vTO!2%!$)30,!9BYPUSHINGTHE;-%.550=;-%.5$/7.=BUTTONS
!REASCREENAPPEARSBYPUSHINGTHE;$!4!50=;$!4!$/7.=BUTTONS0I
When AREA is set to USER, the setting can be changed on the area menu. When changing the area, refer to
the item “7.2 (8) Setting USER area”.
0USHTHE;$)30=BUTTONTORETURNTOTHEMENU1I
(f) Setting of maximum auto shutter speed
Move the “/I vTO-!83(54BYPUSHINGTHE;-%.550=;-%.5$/7.=BUTTONS
3ELECTTHESHUTTERSPEEDBYPUSHINGTHE;$!4!50=;$!4!$/7.=BUTTONS0I
[DATA UP]
[DATA DOWN]
1/200s 1/250s 1/300s 1/350s 1/400s 1/450s 1/500s 1/550s 1/600s 1/700s 1/800s 1/900s 1/1000s 1/1200s 1/1500s 1/2000s 1/4000s OFF

19
Changing the setting in MANUAL mode(1. 2)
Shutter mode AUTO, MANUAL, SS
-- 1 SHUTTER -- (FILE A)
Shutter speed setting
MODE MANUAL OFF, 1/100s, 1/125s, 1/250s, 1/500s, 1/1000s,
MANUAL OFF 1/2000s, 1/3000s, 1/4000s, 1/5000s, 1/10000s
<MODE = MANUAL>
Move up and down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
(a) Changing the shutter speed
Move the “/I vTO-!.5!,BYPUSHINGTHE;-%.550=;-%.5$/7.=BUTTONS
3ELECTTHESHUTTERSPEEDBYPUSHINGTHE;$!4!50=;$!4!$/7.=BUTTONS0I
[DATA DOWN]
[DATA UP]
OFF 1/100s 1/125s 1/250s 1/500s 1/1000s 1/2000s 1/3000s 1/4000s 1/5000s 1/10000s
Changing the setting in SS (Synchro. Scan) mode(1. 3)
Shutter mode AUTO, MANUAL, SS
-- 1 SHUTTER -- (FILE A)
Synchro. scan setting
1/1125H to 1122/1125H, OFF
MODE SS
SYNCHRO SCAN OFF
<MODE = SS>
Move up and down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
(a) Changing the Synchro. Scan setting
Move the “/I vTO39.#(2/3#!.BYPUSHINGTHE;-%.550=;-%.5$/7.=BUTTONS
3ELECTTHE3YNCHRO3CANBYPUSHINGTHE;$!4!50=;$!4!$/7.=BUTTONS0I
;$!4!50=
1/1125H 1122/1125H OFF
;$!4!$/7.=

20
GAIN (Video gain)( 2 )
GAIN has three modes; AUTO, MANUAL, OFF.
Move the “ vTO-/$%PUSHTHE;$!4!50=;$!4!$/7.=ANDSELECTONEOFTHETHREEMODES!54/-!.5!,
OFF. In the OFF mode, gain is fixed to 0dB.
Changing maximum gain in AUTO (AGC: Automatic gain control) mode(2. 1)
-- 2 GAIN -- (FILE A)
Gain mode AUTO, MANUAL, OFF
MODE AUTO
MAX GAIN 20dB AGC maximum gain setting
0dB to 20dB (1dB step)
Move up and down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
Move the “/I vTO-!8'!).BYPUSHINGTHE;-%.550=;-%.5$/7.=BUTTONS
3ELECTTHEDESIREDVALUEOF!'#MAXIMUMGAINBYPUSHINGTHE;$!4!50=;$!4!$/7.=BUTTONS0I
;$!4!50=
0dB 20dB
;$!4!$/7.=
Changing gain in MANUAL mode(2. 2)
-- 2 GAIN -- (FILE A)
Gain mode AUTO, MANUAL, OFF
MODE MANUAL
MANUAL 0dB Manual gain setting
-3dB to 20dB (1dB step)
Move up and down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
Move the “/I vTO-!.5!,BYPUSHINGTHE;-%.550=;-%.5$/7.=BUTTONS
3ELECTTHEDESIREDVALUEOFMANUALGAINBYPUSHINGTHE;$!4!50=;$!4!$/7.=BUTTONS0I
;$!4!50=
-3dB 20dB
;$!4!$/7.=