Toshiba IK-HR1CD User manual

For Customer Use
Enter below the Serial #
which is located on the
bottom of the cabinet. Retain
this information for future ref-
erence.
Model # IK-HR1CD
Serial #
CAMERA CONTROL UNITINSTRUCTION MANUAL
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursu-
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
USER-INSTALLER CAUTION: Yo ur authority to operate this FCC verified equipment could be voided if
you make changes or modifications not expressly approved by the party responsible for compliance to
Part 15 of the FCC Rules.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est comforme à la norme NMB-003 du Canada.
Following information is only for EU-member states:
The use of the symbol indicates that this product may not be treated as household waste.
By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed information about the take-
back and recycling of this product, please contact your supplier where you purchased the
product or consult.
This manual is made from recycled paper.
IK-HR1CD

2
SAFETY PRECAUTIONS
Safety icons
This manual contains safety instructions that must be observed in order to avoid potential
hazards that could result in personal injuries, damage to your equipment, or loss of data.
These safety cautions have been classified according to the seriousness of the risk, and the
icons highlight these instructions as follows:
Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
Stop operation immediately if any abnormality or defect occurs.
Use during an abnormal condition; such as emitting smoke, burning odors, damage
from dropping, invasion of foreign objects, etc. may result in fire and/or electrical
shock. Immediately disconnect the power source and contact your dealer.
Avoid installing in a shower room or a bathroom.
This may result in fire and/or electrical shock.
Do not operate in places where the product may get wet.
This may result in fire and/or electrical shock.
Do not repair, disassemble and/or modify by yourself.
This may result in fire and/or electrical shock. Always be sure to contact your
dealer for internal repair, check and cleaning of the product.
Use the specified power supply.
Otherwise, fire or electrical shock may occur.
Do not place anything on top of the unit.
Foreign materials, such as metals or liquids, getting into the product may result
in fire and/or electrical shock.
Do not put the product on an unstable, slanted or vibrating surface.
The product dropping or falling may result in serious injury.
Do not touch the product or any connection cables during a thunder-
storm.
This may result in electrical shock.

3
Disclaimer
We disclaim any responsibility and shall be held harmless for any damages or losses incurred by the
user in any of the following cases:
1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether inten-
tional or accidental; use under extreme operating conditions.
2. Malfunction or non-function resulting in indirect, additional or consequential damages, including
but not limited to loss of expected income and suspension of business activities.
3. Incorrect use not in compliance with instructions in this instruction manual.
4. Malfunctions resulting from misconnection to other equipment.
5. Repairs or modifications made by the user or caused to be made by the user and carried out by
an unauthorized third party.
6. Notwithstanding the foregoing, Toshiba’s liabilities shall not, in any circumstances, exceed the
purchase price of the product.
Copyright and Right of Portrait
There may be a conflict with the Copyright Law and other laws when a customer uses, displays,
distributes, or exhibits an image picked up by the camera without permission from the copyright
holder. Please also note that transfer of an image or file covered by copyright is restricted to use
within the scope permitted by the Copyright Law.
Protection of Personal Information
Note the following instructions when installing.
•Do not cover the product with any material.
•Do not place the product on any inflammable material such as a carpet or
•Do not place the product in a confined space, as this may cause heat to
build up inside the product.
blanket.
Failure to follow the above cautions may result in fire.
Do not place the product in direct sunshine and/or high temperature.
Temperature build up inside the product may result in fire.
Avoid placing in humid, smoky, or dusty places.
This may result in fire and/or electrical shock.
Do not point the lens directly at the sun and/or intensive light such as di-
rect sunlight, etc.
Focusing of the light may result in eye injury and/or fire.
Ask your dealer to perform a periodical check and internal cleaning (approx.
once every five years).
Dust inside the product may result in fire. For check and cleaning cost, please
consult your dealer.
Images taken by the camera that reveal the likeness of an individual person may be considered
personal information. To disclose, exhibit or transmit those images over the internet or otherwise,
consent of the person may be required.

4
1CAUTIONS ON USE AND INSTALLATION ............................................
2COMPONENTS .......................................................................................
3
ITEMS CONTROLLED BY THE ON SCREEN DISPLAY ........................
4
NAMES AND FUNCTIONS......................................................................
5
CONNECTION........................................................................................
4.1 Standard Connection ..................................................................................................
4.2 Cautions on Connection..............................................................................................
4.3 Connection on Rear Panel..........................................................................................
4.3A Connector Pin Assignments .....................................................................................
6
OPERATION............................................................................................
5.1 White Balance..............................................................................................................
5.2 Gain .............................................................................................................................
5.3 Switching video signal output ......................................................................................
7 MODE SETTING BY THE ON SCREEN DISPLAY................................
7.1 Using the Menus .........................................................................................................
7.3 Menus .........................................................................................................................
(1) SHUTTER (Electronic shutter) ....................................................................................
(1.1) Changing the setting in AUTO mode...................................................................
(1.2) Changing the setting in MANUAL mode..............................................................
(1.3) Changing the setting in SS (Synchro Scan) mode ..............................................
(2) GAIN (Video gain) .......................................................................................................
(2.1) Changing gain in MANUAL mode........................................................................
(3) WHT BAL (White Balance) ..........................................................................................
(3.1) Changing the setting in AWB (Automatic White Balance) mode ........................
(3.2) Changing the setting in ATW (Automatic Tracking White balance) mode .........
(3.3) Changing gain in MANUAL mode .......................................................................
(4) PROCESS ...................................................................................................................
(4.1) Changing gamma correction ON/OFF ................................................................
(4.2) Changing gamma correction level.......................................................................
(4.3) Changing detail (outline) gain..............................................................................
(4.4) Changing DTL B. FREQ (detail boost frequency).............................................
(4.5) Changing master pedestal ..................................................................................
6
6
12
7
8
8
8
9
9
10
10
11
7.2 Scene File ................................................................................................................... 13
12
13
13
14
14
15
16
17
18
18
19
19
20
21
22
22
22
22
23
23
TABLE OF CONTENTS
Limitation of Usage
The product is not designed for any “critical applications.” “Critical applications” means life support
systems, exhaust or smoke extraction applications, medical applications, commercial aviation, mass
transit applications, military applications, homeland security applications, nuclear facilities or systems
or any other applications where product failure could lead to injury to persons or loss of life or
catastrophic property damage. Accordingly, [Toshiba/TAIS] disclaims any and all liability arising out of
the use of the product in any critical applications.
(5) MATRIX(Matrix color correction) .................................................................................
(5.1) Changing Matrix color correction ON/OFF ..........................................................
(5.2) Changing MATRIX setting ...................................................................................
23
23
23

5
(6) OPTION.......................................................................................................................
(6.1) Changing a type of output monitors ....................................................................
24
24
8BEFORE MAKING SERVICE CALL........................................................
9SPECIFICATIONS..................................................................................
10 EXTERNAL APPEARANCE DIAGRAM................................................
25
26
27
(7) Returning to factory settings ....................................................................................... 24
(6.2) Changing RS 232C baud rate ............................................................................
24

6
 &DPHUDFRQWUROXQLW
$FFHVVRULHV
D,QVWUXFWLRQPDQXDO  
 &20321(176
 &$87,2162186($1',167$//$7,21
•Do not shoot intense light.
•Install the camera in a location free from noise.
If the camera or the cables are located near power
utility lines or a TV, etc. undesirable noise may ap-
pear on the screen. In such a case, try to change
the location of the camera or the cable wiring.
•Moire
•Operating ambient temperature and humidity.
Do not use the camera in places where tempera-
ture and humidity exceed the specifications. Pic-
ture quality will deteriolate and internal parts may
be damaged.
Be particularly careful when using in places ex-
posed to direct sunlight. When shooting in hot
places, depending on the conditions of the object
and the camera (for example when the gain is in-
creased), noise in the form of vertical strips or
white dots may occur.
This is not a malfunction.
•Handling of the camera head and the protec-
tion cap.
•This camera is for indoor use only.
•When not using the camera for extended
periods of time.
•When cleaning the camera.
•Avoid using or storing the camera in the fol-
lowing places:
•Installation without a tripod.
•Handling the unit.
Followings are the descriptions about the camera head and this camera.
Do not drop, jolt, or vibrate, as this may result in
damage to the unit. This may cause problems.
Treat the camera cables carefully to prevent
cable problems, such as breaks in the cable and
loose connections.
Keep the camera head and the protection cap
away from children as they may pose a choking
hazard.The protection cap protects the image
sensing plane when the lens is removed from the
camera head, do not discard.
Unplug the power source before cleaning. Clean
with a soft dry cloth only. Do not use any chemicals
or chemically treated cloths. Chemicals may
damage coatings, printing or the paint work.
When cleaning the lens, use lens cleaning paper.
Before installing the camera head and the
camera control unit, make sure that the location
can withstand the total weight of the camera
head and the camera control unit.
If this is not the case, reinforce the area to
prevent the unit from falling, which may result in
damage to the unit or personal injury.
Places filled with highly flammable gas.
Places near gasoline, benzene, or paint thinner.
Places subject to strong vibration.
Places containing chemicals (such as pesticides),
rubber or vinyl products for extended periods of
time.
Switch the control unit off and disconnect the
power supply.
A moire pattern is an interference pattern
generated when two repetitive line patterns
overlap. This is not a malfunction. Eliminating the
repetitive line patterns, or aligning the two
patterns, will eliminate the moire.
When intense light enters, vertical stripes or
transverse band may appear on the screen. This
is not a malfunction. Ghosts may occur when
there is an intense light near the object. In this
case, change the shooting angle.

7







'9,,WHUPLQDO
',63EXWWRQ
5(027(WHUPLQDO

3$*(EXWWRQ
>5HDU@>)URQW@
>%RWWRP@
0(1883EXWWRQ
0(18'2:1EXWWRQ
'$7$83$:%EXWWRQ
'$7$'2:1EXWWRQ
'&,19WHUPLQDO

 1$0(6$1')81&7,216
1080 59.94 P
720 50 i


)250$7VZLWFK
,)WHUPLQDO
㪉
㪈
,)WHUPLQDO &RQQHFWWKHVSHFLDOFDPHUDFDEOH3OHDVHIROORZ&DXWLRQVRQ&RQQHFWLRQDQG
FRQQHFWLW
㽲
)250$7VZLWFK 6ZLWFKWKHYLGHRVLJQDORXWSXW
(IIHFWLYHVFDQQLQJOLQHV6ZLWFKEHWZHHQëDQGë
)DFWRU\GHIDXOW+]
6FDQPRGH6ZLWFKEHWZHHQSURJUHVVLYHSDQGLQWHUODFHL7KLVLVHIIHFWLYH
)DFWRU\GHIDXOW
9HUWLFDOIUHTXHQF\6ZLWFKEHWZHHQ+]DQG+]
RQO\ZKHQWKHHIIHFWLYHVFDQQLQJOLQHVDUHVHWWR)DFWRU\GHIDXOWS
㽳
'&,19WHUPLQDO $FFHSWVD'&SRZHULQSXW9
㽴
5(027(WHUPLQDO 7RFRQQHFWWRD56&GHYLFHIRUUHPRWHFRQWUROIXQFWLRQ
㽵
',63EXWWRQ 8VHGZKHQVZLWFKLQJWKHGLVSOD\
㽶
3$*(EXWWRQ 8VHGZKHQVZLWFKLQJWRWKHPHQXDQGZKHQVHOHFWLQJWKHPHQXV
㽷
0(1883EXWWRQ 6HOHFWWKHIXQFWLRQWREHFRQILUPHGRUFKDQJHGRQWKHPHQX
㽸
0(18'2:1EXWWRQ 6HOHFWWKHIXQFWLRQWREHFRQILUPHGRUFKDQJHGRQWKHPHQX
㽹
'$7$83$:%EXWWRQ &KDQJHVWKHYDOXHRIWKHIXQFWLRQVHOHFWHGE\WKH0(1883'2:1EXWWRQ$OVR
XVHGZKHQXVLQJ$:%
㽺
'$7$'2:1EXWWRQ &KDQJHVWKHYDOXHRIWKHIXQFWLRQVHOHFWHGE\WKH0(1883'2:1EXWWRQ
㽻
'9,,WHUPLQDO 2XWSXWV'9,,WRFRQQHFWWRD'9,PRQLWRU
㽼
0RXQWLQJKROHV0 8VHGWRDWWDFKWKHFDPHUDWRDPRXQW:KHQXVLQJDWULSRGDWWDFKWKHPRXQWLQJ
EUDFNHW-..7)RSWLRQWRWKHVHKROHV
㽽
0RXQWLQ
J
KROHV0 8VHGWRDWWDFKWKHFDPHUDWRDPRXQW
㽾

8
 6WDQGDUG&RQQHFWLRQ
 &211(&7,21
,.+5&',.+5+
'&,19
/HQV
RSWLRQ
&DPHUDKHDG
RSWLRQ
&DPHUDFRQWUROXQLW
'9,FDEOH
QRWVXSSOLHG'9,WHUPLQDO
'9,PRQLWRU
QRWVXSSOLHG
'&SRZHUVXSSO\

RSWLRQ


6SHFLDOFDPHUDFDEOH
RSWLRQ
䊶:KHQFRQQHFWLQJWKHFDPHUDFDEOHVEHVXUHWRWXUQRIIWKHFDPHUDFRQWUROXQLWDQG
DQ\RWKHUHTXLSPHQWFRQQHFWHGWRLW
:HVXJJHVWXVLQJD&PRXQWOHQVDFFHSWHGPLOOLRQSL[HO:KHQXVLQJRWKHU
OHQVHVWKHEHVWFDPHUDSHUIRUPDQFHRIWKLVFDPHUDPD\QRWEHREWDLQHG
)RUH[DPSOHORZUHVROXWLRQPD\RFFXUIRFXVPD\EHORVWWKURXJKWKHUDQJHRI
D]RRPOHQVDQGIODUHJKRVWLQJPD\RFFXU
)XUWKHUPRUHLQRUGHUWRDYRLGGDPDJLQJWKHPRXQWLQJSRUWLRQRIWKHFDPHUDKHDG
XVHDOHQVZKLFKKDVDSURMHFWLRQGLPHQVLRQIURPWKHPRXQWLQJEDVHRIOHVVWKDQ
PP
䊶
3OHDVHPDNHVXUHWRXVHWKHVSHFLDOFDPHUDFDEOHZKHQFRQQHFWLQJWKH
FDPHUDKHDGZLWKWKHFDPHUDFRQWUROXQLW
7KHFDPHUDFDEOHLVGLUHFWLRQGHSHQGHQW3OHDVHFRQILUPWKHFRQQHFWRU
LQGLFDWLRQDQGFRQQHFWLWIROORZLQJWKHILJXUHDERYH
䊶
,IWKHVFUHZVRQWKHFDPHUDFDEOHFRQQHFWRUVDUHQRWVHFXUHRUKDYHEHHQ
ORRVHQHGQRLVHPD\RFFXULQWKHYLGHRLPDJH3OHDVHPDNHVXUHWRVHFXUH
WKHVFUHZWLJKWO\
䊶
7KLVFDPHUDFRQWUROXQLWZDVGHVLJQHGWREHXVHGZLWKWKH7RVKLEDFDPHUD
KHDG,.+5+RSWLRQ'RQRWFRQQHFWLWZLWKDQ\RWKHUHTXLSPHQW
䊶
䊶)RU'&SRZHUVXSSO\FRQQHFWLQJWR'&,19WHUPLQDOXVH8/OLVWHGDQGRU&6$
DSSURYHGXQJURXQGHGW\SH$&DGDSWRUZLWKWKHVSHFLILFDWLRQVGHVFULEHGEHORZ
3RZHUVXSSO\YROWDJH 䋺9'& 㫧
&XUUHQWUDWLQJ 䋺0RUHWKDQP$
5LSSOHYROWDJH 䋺/HVVWKDQP9SS
&RQQHFWRU䋺+5$36E\+,526(HOHFWURQLFV&R/WG
3LQV 䋺9
3LQV 䋺*1'
 &DXWLRQVRQ&RQQHFWLRQ
7KLVFDPHUD¶VRXWSXWPRGHIRUWKHYLGHRVLJQDOLVQRWFRQWUROOHGDXWRPDWLFDOO\
IRUWKH'9,PRQLWRUUHVROXWLRQ,IDPRQLWRUGRHVQRWVXSSRUWWKLVFDPHUD¶V
RXWSXWPRGHLWZLOOQRWGLVSOD\DQ\WKLQJ3OHDVHPDWFKWKHPRQLWRUUHVROXWLRQ
DQGWKHIRUPDWVZLWFK5HIHUWRWKHLWHP³6ZLWFKLQJYLGHRVLJQDORXWSXW´IRU
WKHRSHUDWLRQ
'9,VWDQGDUG
'9,'LJLWDO9LVXDO,QWHUIDFHLVDQLQWHUIDFHVWDQGDUGIRUFRQQHFWLQJIODWSDQHO
GLVSOD\VVXFKDVOLTXLGFU\VWDOGLVSOD\
'9,FRQQHFWRUKDVWKUHHW\SHV'9,,LQWHJUDWHGGLJLWDODQGDQDORJ'9,'
GLJLWDORQO\DQG'9,$DQDORJRQO\LQDFFRUGDQFHZLWKDPRXQWLQJVLJQDO
FRQGXFWRU8VHD'9,FDEOHQRWVXSSOLHGEHWZHHQWKHFDPHUDDQGWKHPRQLWRU
RUGLVSOD\
㪠㪆㪝
1080 59.94P
72050i
㩿
㪚㪚㪬
㪀
㪠㪆㪝
㩿㪚㪘㪤㪜㪩㪘㩷㪟㪜㪘㪛㪀
&DPHUDKHDG5HDU
&DPHUDFRQWUROXQLW)URQW
3OHDVHPDWFKWKHODEHOLQJRQWKHFDPHUD
WRWKHODEHOLQJRQWKHFDEOH
3OHDVHPDWFKWKHODEHOLQJRQWKHFDPHUD
WRWKHODEHOLQJRQWKHFDEOH
㪚㪘㪤㪜㪩㪘㩷㪟㪜㪘㪛
㪚㪚㪬

9
'9,,WHUPLQDO
 $&RQQHFWRU3LQ$VVLJQPHQWV
'&,19WHUPLQDO
 9
 9
 *1'
 *1'
5(027(WHUPLQDO



7;'
5;'
*1'






1&
 $QDORJ9HUWLFDO6\QF
1&
1&
1&
'DWD
'DWD
'DWD6KLHOG*1'






 *1'
 +RW3OXJ'HWHFW
1&
1&
9
'DWD
'DWD
'DWD6KLHOG*1'






 &ORFN
 &ORFN
&$QDORJ5HG
&
$QDORJ+RUL]RQWDO6\QF
&$QDORJ*UHHQ
&$QDORJ*1'
&$QDORJ%OXH
1&
1&
&ORFN6KLHOG*1'
'DWD
'DWD
'DWD6KLHOG*1'
5HDUSDQHOYLHZ
 &RQQHFWLRQRQ5HDU3DQHO
㪩㪜㪤㪦㪫㪜㩷㫋㪼㫉㫄㫀㫅㪸㫃
C1
1
9
17
2
10
18
3
11
19
4
12
20
5
13
21
6
14
22
7
15
23
8
16
24
C2
C3 C4
C5
1
1
2
3
4
23
)RUFRQQHFWLQJWRWKH5(027(WHUPLQDOXVHDVKLHOGHGFDEOH&RQQHFWWKHFDEOHFRUUHFWO\
RULWPD\EHGDPDJHG

10
㽲5HIHUWRWKHLWHP&211(&7,21DQGFRQQHFWWKHHTXLSPHQWFRUUHFWO\
㽳7XUQRQWKHFRQQHFWHGHTXLSPHQWDQGWKHFDPHUD
㽴$LPWKHOHQVDWWKHREMHFWDGMXVWWKHOHQVLULVDGMXVWPHQWIRFXVDGMXVWPHQWHWF
㽵5HIHUWRWKHLWHP³:KLWH%DODQFH´PDNHWKHDGMXVWPHQW
㽶
㽲
㽳
㽴
㽵
㽶
5HIHUWRWKHLWHPV³*DLQ´³6ZLWFKLQJYLGHRVLJQDORXWSXW´³02'(6(77,1*%<7+(21
6&5((1',63/$<´VHOHFWWKHQHFHVVDU\LWHPV
 23(5$7,21
$7:
$XWRPDWLF7UDFNLQJ
:KLWH%DODQFH䋩
䋩䋩
䋩
$:%
䋨
䋨䋨
䋨䋨
䋨䋨
䋨$XWRPDWLF:KLWH%DODQFH䋩
䋩䋩
䋩
0$18$/
䋨
䋨䋨
䋨0DQXDO:KLWH%DODQFH䋩
䋩䋩
䋩
2XWOLQH
7KHFDPHUDPHDVXUHVWKH
REMHFWFRORUWHPSHUDWXUHDQG
DGMXVWVWKHZKLWHEDODQFH
DXWRPDWLFDOO\
$GMXVWZKLWHEDODQFHE\
GLVSOD\LQJWKHZKLWHREMHFW
LQVLGHWKHDUHDVHWE\$:%
PHQXDQGSUHVVLQJWKH
>'$7$83@EXWWRQ
$GMXVWWKHZKLWHEDODQFH
PDQXDOO\XVLQJWKH:+7
%$/PHQXZKLOHVKRRWLQJ
WKHZKLWHREMHFW 
)HDWXUHV
7UDFNVYDULDWLRQVRIFRORU
WHPSHUDWXUHDQGDGMXVWVZKLWH
EDODQFHDXWRPDWLFDOO\
0HDVXUHPHQWDFFXUDF\LV
KLJKHUWKDQ$7:7KLV
PRGHLVHIIHFWLYHZKHQ
VKRRWLQJXQGHUOHVVYDULD
WLRQVRIFRORUWHPSHUDWXUH
$UWLILFLDOZKLWHEDODQFHVHWWLQJ
7KHPDQXDODGMXVWPHQWLV
PRVWHIIHFWLYHXQGHUVKRRWLQJ
FRQGLWLRQVZLWKQRFRORU
WHPSHUDWXUHYDULDWLRQ
1RWHV
,ILOOXPLQDWLRQLVORZZKLWH
EDODQFHPD\QRWEHFRUUHFWHG
$GMXVWPHQWLVSHUIRUPHGE\
FRQILUPLQJZLWKDPRQLWRU
$:%$XWRPDWLF:KLWH%DODQFH
6HWWKH02'(WR$:%RQWKH:+7%$/PHQX
3HUIRUPWKH&7(03FRORUWHPSHUDWXUHFRQYHUVLRQVHWWLQJLIQHFHVVDU\
5HIHUWRWKHLWHP³:+7%$/:KLWH%DODQFH´
.䋺$SSURSULDWHIRULQGRRUVKRRWLQJ
.䋺$SSURSULDWHIRURXWGRRUVKRRWLQJ
,IWKHFRORUEDUSDWWHUQLVGLVSOD\HGRQWKHVFUHHQRULIWKHLQGH[PHQXPHQXLVGLVSOD\HGSUHVVWKH>',63@
EXWWRQ WRGLVDEOHWKHFRORU EDU SDWWHUQ RUWKHFKDUDFWHU GLVSOD\ RQ WKH VFUHHQ
6KRRWD NQRZQZKLWHREMHFWHQWLUHO\ LQ WKHDUHDVHWE\WKH$:%PHQXUHIHUWR WKHLWHP³G
&RQILUPLQJWKHFRQWHQWVRIWKH]RQHDUHDVHOHFWHGE\$:%´DQGSUHVV>'$7$83@EXWWRQIRUDSSUR[VHFRQG
7KHFKDUDFWHU$:%EOLQNVRQWKHVFUHHQZKHQWKH$:%VWDUWV
7KHFKDUDFWHU$:%VWRSVEOLQNLQ
J
ZKHQWKH$:%ILQLVKHVDQGWKHUHVXOWLVGLVSOD
\
HGIRUDSSUR[VHFRQG
 :KLWH%DODQFH
)RU ZKLWH EDODQFH DGMXVWPHQW RI WKLV XQLW $7: $XWRPDWLF 7UDFNLQJ :KLWH EDODQFH $:% $XWRPDWLF
:KLWH%DODQFHDQG0$18$/0DQXDOZKLWHEDODQFHDGMXVWPHQWVDUHSURYLGHG5HIHUWRWKHLWHP³
:+7%$/:KLWH%DODQFH´VHOHFWWKHGHVLUHGPRGH

11
0HDQLQJ'LVSOD\
$:%2. $XWRPDWLFZKLWHEDODQFHDGMXVWPHQWILQLVKHGFRUUHFWO\
$:%1*
/(9(//2:
$XWRPDWLFZKLWHEDODQFHDGMXVWPHQWFDQQRWEHSHUIRUPHGEHFDXVHWKHYLGHROHYHOLV
WRRORZ
$GMXVWWKHYLGHROHYHOE\LQFUHDVLQJWKHLOOXPLQDWLRQRURSHQLQJWKHOHQVLULV
$:%1*
/(9(/+,*+
$XWRPDWLFZKLWHEDODQFHDGMXVWPHQWFDQQRWEHSHUIRUPHGEHFDXVHWKHYLGHROHYHOLV
WRRKLJK
$GMXVWWKHYLGHROHYHOE\GHFUHDVLQJWKHLOOXPLQDWLRQRUFORVLQJWKHOHQVLULV
$:%1*
&7(03/2:
$XWRPDWLF ZKLWH EDODQFH DGMXVWPHQW FDQQRWEH SHUIRUPHG EHFDXVH WKH FRORU
WHPSHUDWXUHLVWRRORZ
,IWKH&7(03LVVHWWR.VHWWR.
,IWKH PHVVDJH DSSHDUV ZLWK WKH &7(03VHWWR . FKDQJH WKHLOOXPLQDWLRQ RU
XVHDFRORUWHPSHUDWXUHFRQYHUVLRQILOWHU
$:%1*
&7(03+,*+
$XWRPDWLF ZKLWH EDODQFH DGMXVWPHQW FDQQRWEH SHUIRUPHG EHFDXVH WKH FRORU
WHPSHUDWXUHLVWRRKLJK
,IWKH&7(03LVVHWWR.VHWWR.
,IWKH PHVVDJH DSSHDUV ZLWK WKH &7(03VHWWR . FKDQJH WKHLOOXPLQDWLRQ RU
XVHWKHFRORUWHPSHUDWXUHFRQYHUVLRQILOWHU
$:%1*$XWRPDWLFZKLWHEDODQFHDGMXVWPHQWFDQQRWEHSHUIRUPHGIRURWKHUUHDVRQV6XFKDV
QRZKLWHDUHDLVLQFOXGHGLQDQREMHFWHWF
0$18$/0DQXDOZKLWHEDODQFH
6HWWKH02'(WR0$18$/RQWKH:+7%$/PHQX
5HIHUWRWKHLWHP³:+7%$/:KLWH%DODQFH´
6KRRWDNQRZQZKLWHREMHFWVHWWKHZKLWHEDODQFHE\DGMXVWLQJWKHOHYHOVRI5*$,1DQG%*$,1RQWKH
PHQXFRQILUPLQJZLWKDPRQLWRURUDYHFWRUVFRSH
5HIHUWRWKHLWHP³&KDQJLQJJDLQLQ0$18$/PRGH´ 
㽲
㽳
(1) MANUAL(Manual gain)
Gain adjustment is performed on the GAIN menu. The adjustment range is from 0 to 18dB in 1dB steps.
(Refer to the item “7.3 (2) (2.1) Changing gain in MANUAL mode”.)
(2) OFF
Gain is fixed at 0 dB.
53 Switching video signal output
52 Gain
Note:
White, red, green, or blue dots may occur when the gain is increased. This is not a malfunction, just
certain characteristics of the CMOS sensor becoming more visible.
When the image is dark even if the lens iris is open, change the gain (video gain) to get the desired video level.
For gain adjustment of the unit, MANUAL (Manual), OFF (0 dB) modes are provided. Select the mode on
the GAIN menu. (Refer to the item “7.3 (2) GAIN (Video gain)”.)
Effective
scanning lines Vertical frequencyScan mode
1920×1080/59.94Hz (Progressive)
1920×1080/50Hz (Progressive)
1920×1080/59.94Hz (Interlace)
1920×1080/50Hz (Interlace)
1280×720/59.94Hz (Progressive)
1280×720/50Hz (Progressive)
1080
1080
1080
1080
720
720
59.94
50
59.94
50
59.94
50
p
p
i
i
p
p
*
*
*The output value is 720p even if ’i’ is selected.
Settings
Switch statusVideo output
A FORMAT switch on the front of the camera can switch the video signal output.

12
(1) MANUAL(Manual gain)
Gain adjustment is performed on the GAIN menu. The adjustment range is from 0 to 18dB in 1dB steps.
(Refer to the item “7.3 (2) (2.1) Changing gain in MANUAL mode”.)
(2) OFF
Gain is fixed at 0 dB.
53 Switching video signal output
52 Gain
Note:
White, red, green, or blue dots may occur when the gain is increased. This is not a malfunction, just
certain characteristics of the CMOS sensor becoming more visible.
When the image is dark even if the lens iris is open, change the gain (video gain) to get the desired video level.
For gain adjustment of the unit, MANUAL (Manual), OFF (0 dB) modes are provided. Select the mode on
the GAIN menu. (Refer to the item “7.3 (2) GAIN (Video gain)”.)
Effective
scanning lines Vertical frequencyScan mode
1920×1080/59.94Hz (Progressive)
1920×1080/50Hz (Progressive)
1920×1080/59.94Hz (Interlace)
1920×1080/50Hz (Interlace)
1280×720/59.94Hz (Progressive)
1280×720/50Hz (Progressive)
1080
1080
1080
1080
720
720
59.94
50
59.94
50
59.94
50
p
p
i
i
p
p
*
*
*The output value is 720p even if ’i’ is selected.
Settings
Switch statusVideo output
A FORMAT switch on the front of the camera can switch the video signal output.
Available selectionsItem
AUTO, MANUAL, SSMODE
MANUAL, OFFMODE
AWB, ATW, MANUALMODE
AUTO level -100
0dB 18dB
0 100
AUTO peak : average 00 10 05 05 10 00
AUTO response speed 1 10 20
AUTO area PRESET A, PRESET B, PRESET C, PRESET D, PRESET E
MANUAL shutter speedOFF, 1/100s, 1/125s, 1/250s, 1/500s, 1/1000s, 1/2000s, 1/4000s
MANUAL gain
3200K, 5600KColor temperature
AWB R PAINT -100 10
AWB B PAINT -100 10
AWB area PRESET A, PRESET B, PRESET C, PRESET D, PRESET E
ATW R PAINT -100 10
-100 10
ATW B PAINT -100 10
MANUAL R GAIN -100 0 100
MANUAL B GAIN -100 0 100
FFO,NOGamma correction
Gamma correction level
Detail gain -7 70
Detail boost frequency HIGH, NORMAL, LOW
Monitor PC, TV
Master pedestal -128 0 127
ON, OFFColor correction ON/OFF
R hue -150 15
R gain -150 15
G hue -150 15
G gain -150 15
B hue -150 15
B gain -150 15
Ye hue -150 15
Ye gain -150 15
Cy hue -150 15
Cy gain -150 15
Mg hue -150 15
Mg gain -15 0 15
Electronic shutter Gain White balance Process Option
Matrix color correction
6ITEMS CONTROLLED BY THE ON SCREEN DISPLAY
Preset value
(Factory setting)
MANUAL
OFF (Note 2)
OFF (Note 1)
1123/1125H
748/750H
AWB
0
50 05
10
PRESET A
0dB
3200K
0
0
PRESET A
0
0
0
0
ON
0
0
HIGH
PC
0
ON
0
0
0
0
0
0
0
0
0
0
0
0
9600bps9600bps, 19200bpsRS232C baud rate
Note 1: 1/60s (when set to 59.94Hz) or 1/50 (when set to 50Hz)
Note 2: gain 0dB
Synchro. scan 15/1125Hto1123/1125H (When set to 1080)
10/750Hto748/750H (When set to 720)
to to
to to
toto
to
to to
to to
to to
to to
to to
to to
to to
to to
to to
to to
to to
to to
to to
to to
to to
to to
to to
to to
to to
to to
to to

13
Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The
contents once set are memorized in the scene files (A, B, C, D, E) selected, so if the power turns off, it is
unnecessary to set the values again when using the unit next time. When the setting is performed, select
the menu of the item to be set.
7MODE SETTING BY THE ON SCREEN DISPLAY
71 Using the Menus
When the unit is powered on, the normal screen showing only the video signal appears. Change the
output to each screen (video signal output, color bar screen, index menu, and menus) by using the
[DISP], [PAGE], [MENU UP], [MENU DOWN], [DATA UP], and [DATA DOWN] buttons.
* A menu is selected when pushing the [PAGE] button after moving the “㸢” on the screen by the [MENU
UP], [MENU DOWN] button while the Index menu is displayed.
POWER ON
Video signal output
DISP
PA GE
PA GE
1.SHUTTER2.GAIN3.WHT BAL 4.PROCESS5.MAT RIX6.OPTION
Color bar screen
Menus
Index menu
DISP DISP
PA GE PA GE PAGE PA GE
PA GE PA GE
MANUAL
OFF
NOAWB
OFFATW
MANUAL
GAMMA
ON
GAMMA
OFF
AUTO
MANUAL
SS
PA GE
DISP
72 Scene File
䌛DATA UP䌝
FILE A ¸¸FILE B ¸¸FILE C ¸¸FILE D ¸¸FILE E
䌛DATA DOWN䌝
Five scene files (A, B, C, D, E) are available as user memories for this unit. These are chosen depending
on shooting conditions. By pressing [DATA UP], [DATA DOWN] buttons while [DISP] button is pressed
and the index menu is displayed, the camera operation is changed immediately from the currently
selected scene file to the next. on shooting conditions. By pressing [DATA UP], [DATA DOWN] buttons
while the Index menu is displayed, the camera operation is changed immediately from the currently
selected scene file to the next.
Note:
Scene file does not contain the data of set "OPTION."
(Refer to the item "7.3 Menus" (6) "OPTION" for the "OPTION" setting.)

14
䊶Select the menu to change the setting by referring to the item “7.1 Using the Menus”.
䊶When the [MENU UP], [MENU DOWN] buttons are pressed, the “㸢” on the screen moves up and down.
Move the “㸢” to the item whose setting you wish to change.
1 SHUTTER䋨Electronic shutter䋩
The electronic shutter has three modes; AUTO, MANUAL, SS(Synchro Scan).
Press the “Page” button to enter the Shutter Page. Use the “Data Up/Down” buttons to select the Shutter
Mode.
AUTO 䋺The exposure time is controlled automatically to obtain the video level set.
MANUAL 䋺It is possible to select the exposure time from eight speed settings;
OFF (1/60s: when set to 59.94Hz, 1/50s: when set to 50Hz), 1/100s,
1/125s, 1/250s, 1/500s, 1/1000s, 1/2000s, 1/4000s.
SS 䋺Shutter speed can be set by the horizontal scanning time (1H) unit.
73 Menus
䌛DATA UP䌝
AUTO ¸¸MANUAL ¸¸SS
䌛DATA DOWN䌝
Note:
½When setting a rapid shutter speed, sensitivity degrades according to the speed.
When a discharging light such as fluorescent lamp, etc. is used for the illumination,
the flicker may be large.
½When an object is moving rapidly, the monitor may display the image distorted and/or
blurred. Also, when a discharging light such as fluorescent lamp, etc. is used for the
illumination, light and dark banding patterns may be displayed on the screen.
Depending on the timing of flash and/or strobe firing, the contrast may be displayed
on the screen. These are not malfunctions, just certain characters of the rolling
shutter system.
½When the shutter speed setting is high, the hue may change depending on shooting
conditions or objects.

15
(c) Changing the automatic shutter response speed
㽲Move the “㸢” to SPEED by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select the response speed by presshing [DATA UP], [DATA DOWN] buttons.
1 10 20
The response speed becomes faster by pressing [DATA UP]
The response speed becomes slower by pressing [DATA DOWN]
(b) Changing the automatic shutter detection (ratio between peak and average value)
㽲Move the “㸢” to PEAK/AVE by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select the ratio between peak and average value by presshing [DATA UP], [DATA DOWN] buttons.
00:10 05:05 10:00
The peak value increases by pressing [DATA UP]
The peak value decreases by pressing [DATA DOWN]
(Peak:Average)
䋨
䋨䋨
䋨1䋮
䋮䋮
䋮1䋩
䋩䋩
䋩Changing the setting in AUTO mode
Shutter mode AUTO, MANUAL, SS
Video level adjustment -100 to 100
Peak and average ratio adjustment 00 10 to 10 00
-- 1 SHUTTER -- (FILE A)
Automatic shutter response speed adjustment 1 to 20
MODE
LEVEL
Automatic shutter area selection
PEAK AVE 05
PRESET A, PRESET B, PRESET C, PRESET D, PRESET E
SPEED
AREA
AUTO
0
05
10
PRESET A
< MODE = AUTO>
Move up and down
by pressing
MENU UP,DOWN
Select the desired
value by pressing
DATA UP,DOWN
(a) Changing the video level in the automatic shutter mode
㽲Move the “㸢” to LEVEL by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select the video level by pressing [DATA UP], [DATA DOWN] buttons.
-100 0 100
The value increases by pressing [DATA UP]
The value increases by pressing [DATA DOWN]

16
(d) Changing the automatic shutter zone area
The available picture area is shown by the shading correction on the screen that is divided into 64.
㽲Move the “㸢” to AREA by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select the measurement light area by pressing [DATA UP], [DATA DOWN] buttons.
䌛DATA UP䌝
PRESET A PRESET B PRESET C PRESET D PRESET E
䌛DATA DOWN䌝
PRESET APRESET BPRESET DPRESET C
PRESET E
䋨
䋨䋨
䋨1䋮
䋮䋮
䋮2䋩
䋩䋩
䋩Changing the setting in MANUAL mode
Shutter mode AUTO, MANUAL, SS
-- 1 SHUTTER -- (FILE A)
Shutter speed setting
MODE MANUAL OFF, 1/100s, 1/125s, 1/250s, 1/500s, 1/1000s,
MANUAL OFF 1/2000s, 1/4000s
< MODE = MANUAL>
(a) Changing the shutter speed
㽲Move the “㸢” to MANU by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select the shutter speed by pressing [DATA UP], [DATA DOWN] buttons.
Move up and down
by pressing
MENU UP,DOWN
Select the desired
value by pressing
DATA UP,DOWN
䌛DATA UP䌝
OFF 1/100s 1/125s 1/250s 1/500s 1/1000s 1/2000s 1/4000s
䌛DATA DOWN䌝
Note:
½The shutter speed can be set in every effective scanning line (1080/720).
½The figures of shutter speed in the menu screen are approximate. The accurate shutter speed is
calculated using the following mathematical formula.
When shutter speed is off:
at 59.94Hz: 1/60s
at 50Hz: 1/50s
Shutter speed (s) = 1/67433(Hz) × n (n=15 to 1123 (integral number)) (when set to 1080/59.94p,1080/59.94i)
1/56250(Hz) × n (n=15 to 1123 (integral number)) (when set to 1080/50p,1080/50i)
1/44955(Hz) × n (n=10 to 748 (integral number)) (when set to 720/59.94p)
1/37500(Hz) × n (n=10 to 748 (integral number)) (when set to 720/50p)

17
䋨
䋨䋨
䋨1䋮
䋮䋮
䋮3䋩
䋩䋩
䋩Changing the setting in SS (Synchro Scan) mode
Shutter mode AUTO, MANUAL, SS
Synchro scan setting
-- 1 SHUTTER -- (FILE A)
MODE SS
SYNCHRO SCAN 1123/1125H
< MODE = SS >
(a) Changing the shutter speed setting
㽲Move the “㸢” to SYNCHRO SCAN by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select the shutter speed by pressing [DATA UP], [DATA DOWN] buttons.
Move up and down
by pressing
MENU UP,DOWN
Select the desired
value by pressing
DATA UP,DOWN
Note:
The shutter speed can be set in every effective scanning line (1080/720).
䌛DATA UP䌝
䌛DATA DOWN䌝
15/1125H ¸1123/1125H (when set to 1080p/1080i)
10/750H ¸748/750H (when set to 720p)
15/1125H to 1123/1125H (when set to 1080p/1080i)
10/750H to 748/750H (when set to 720p)
䋨
䋨䋨
䋨1䋮
䋮䋮
䋮2䋩
䋩䋩
䋩Changing the setting in MANUAL mode
Shutter mode AUTO, MANUAL, SS
-- 1 SHUTTER -- (FILE A)
Shutter speed setting
MODE MANUAL OFF, 1/100s, 1/125s, 1/250s, 1/500s, 1/1000s,
MANUAL OFF 1/2000s, 1/4000s
< MODE = MANUAL>
(a) Changing the shutter speed
㽲Move the “㸢” to MANU by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select the shutter speed by pressing [DATA UP], [DATA DOWN] buttons.
Move up and down
by pressing
MENU UP,DOWN
Select the desired
value by pressing
DATA UP,DOWN
䌛DATA UP䌝
OFF 1/100s 1/125s 1/250s 1/500s 1/1000s 1/2000s 1/4000s
䌛DATA DOWN䌝
Note:
½The shutter speed can be set in every effective scanning line (1080/720).
½The figures of shutter speed in the menu screen are approximate. The accurate shutter speed is
calculated using the following mathematical formula.
When shutter speed is off:
at 59.94Hz: 1/60s
at 50Hz: 1/50s
Shutter speed (s) = 1/67433(Hz) × n (n=15 to 1123 (integral number)) (when set to 1080/59.94p,1080/59.94i)
1/56250(Hz) × n (n=15 to 1123 (integral number)) (when set to 1080/50p,1080/50i)
1/44955(Hz) × n (n=10 to 748 (integral number)) (when set to 720/59.94p)
1/37500(Hz) × n (n=10 to 748 (integral number)) (when set to 720/50p)

18
2 GAIN (Video gain)
GAIN has two modes; MANUAL, OFF.
Move the “ ” to MODE, press the [DATA UP], [DATA DOWN], and select one of the two modes :
MANUAL, OFF. In the OFF mode, gain is fixed to 0dB.
㸢
䋨
䋨䋨
䋨2䋮
䋮䋮
䋮1䋩
䋩䋩
䋩Changing gain in MANUAL mode
-- 2 GAIN -- (FILE A)
Gain mode MANUAL, OFF
MODE
MANUAL
MANUAL
0dB Manual gain setting
0dB to 18dB (1dB step)
㽲Move the “㸢” to MANUAL by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select the desired value of manual gain by pressing [DATA UP], [DATA DOWN] buttons.
Move up and down
by pressing
MENU UP,DOWN
Select the desired
value by pressing
DATA UP,DOWN
䌛DATA UP䌝
0dB 18dB
䌛DATA DOWN䌝
䋨
䋨䋨
䋨3䋩
䋩䋩
䋩WHT BAL(White Balance)
The WHT BAL has three modes; AWB, ATW, MANUAL.
Move the “ ” to MODE, press the [DATA UP], [DATA DOWN], and select one of the three modes :
AWB, ATW, MANUAL.
㸢
䋨
䋨䋨
䋨3䋮
䋮䋮
䋮1䋩
䋩䋩
䋩Changing the setting in AWB(Automatic White Balance) mode
White balance mode setting AWB, ATW, MANUAL
R PAINT adjustment -10 to 10
-- 3 WHT BAL -- (FILE A)
B PAINT adjustment -10 to 10
MODE
CTEMP
Color temperature setting 3200K, 5600K
R PAINT
B PAINT
AWB area
AREA
AWB
3200K
0
0
PRESET A PRESET A, PRESET B, PRESET C, PRESET D, PRESET E
Move up and down
by pressing
MENU UP,DOWN
Select the desired
value by pressing
DATA UP,DOWN

19
(c) Changing color temperature setting
㽲Move the “㸢” to C.TEMP by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select either 3200K or 5600K by pressing [DATA UP], [DATA DOWN] buttons.
(a) Changing R PAINT
㽲Move the “㸢” to R PAINT by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select the desired value of red paint by pressing [DATA UP], [DATA DOWN] buttons.
(b) Changing B PAINT
㽲Move the “㸢” to B PAINT by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select the desired value of blue paint by pressing [DATA UP], [DATA DOWN] buttons.
(d) Confirming the contents of the zone area selected by AWB
㽲Move the “㸢” to AREA DISP by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select the desired area by pressing [DATA UP], [DATA DOWN] buttons.
-10 0 10
[DATA UP] ¸Red is increased.
Red is decreased. ¸[DATA DOWN]
-10 0 10
[DATA UP] ¸Blue is increased.
Blue is decreased. ¸[DATA DOWN]
The available picture area is shown by the shading correction on the screen that is divided into 64.
PRESET APRESET BPRESET DPRESET C
PRESET E
䋨
䋨䋨
䋨2䋮
䋮䋮
䋮1䋩
䋩䋩
䋩Changing gain in MANUAL mode
-- 2 GAIN -- (FILE A)
Gain mode MANUAL, OFF
MODE
MANUAL
MANUAL
0dB Manual gain setting
0dB to 18dB (1dB step)
㽲Move the “㸢” to MANUAL by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select the desired value of manual gain by pressing [DATA UP], [DATA DOWN] buttons.
Move up and down
by pressing
MENU UP,DOWN
Select the desired
value by pressing
DATA UP,DOWN
䌛DATA UP䌝
0dB 18dB
䌛DATA DOWN䌝
䋨
䋨䋨
䋨3䋩
䋩䋩
䋩WHT BAL(White Balance)
The WHT BAL has three modes; AWB, ATW, MANUAL.
Move the “ ” to MODE, press the [DATA UP], [DATA DOWN], and select one of the three modes :
AWB, ATW, MANUAL.
㸢
䋨
䋨䋨
䋨3䋮
䋮䋮
䋮1䋩
䋩䋩
䋩Changing the setting in AWB(Automatic White Balance) mode
White balance mode setting AWB, ATW, MANUAL
R PAINT adjustment -10 to 10
-- 3 WHT BAL -- (FILE A)
B PAINT adjustment -10 to 10
MODE
CTEMP
Color temperature setting 3200K, 5600K
R PAINT
B PAINT
AWB area
AREA
AWB
3200K
0
0
PRESET A PRESET A, PRESET B, PRESET C, PRESET D, PRESET E
Move up and down
by pressing
MENU UP,DOWN
Select the desired
value by pressing
DATA UP,DOWN

20
䋨
䋨䋨
䋨3䋮
䋮䋮
䋮2䋩
䋩䋩
䋩Changing the setting in ATW(Automatic Tracking White balance) mode
White balance mode AWB, ATW, MANUAL
-- 3 WHT BAL -- (FILE A)
R PAINT adjustment -10 to 10
MODE
R PAINT B PAINT adjustment -10 to 10
B PAINT
ATW
0
0
(a) Changing R PAINT
㽲Move the “㸢” to R PAINT by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select the desired value of red paint by pressing [DATA UP], [DATA DOWN] buttons.
Move up and down
by pressing
MENU UP,DOWN
Select the desired
value by pressing
DATA UP,DOWN
(b) Changing B PAINT
㽲Move the “㸢” to B PAINT by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select the desired value of blue paint by pressing [DATA UP], [DATA DOWN] buttons.
-10 0 10
[DATA UP] ¸Red is increased.
Red is decreased. ¸[DATA DOWN]
-10 0 10
[DATA UP] ¸Blue is increased.
Blue is decreased. ¸[DATA DOWN]
(c) Changing color temperature setting
㽲Move the “㸢” to C.TEMP by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select either 3200K or 5600K by pressing [DATA UP], [DATA DOWN] buttons.
(a) Changing R PAINT
㽲Move the “㸢” to R PAINT by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select the desired value of red paint by pressing [DATA UP], [DATA DOWN] buttons.
(b) Changing B PAINT
㽲Move the “㸢” to B PAINT by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select the desired value of blue paint by pressing [DATA UP], [DATA DOWN] buttons.
(d) Confirming the contents of the zone area selected by AWB
㽲Move the “㸢” to AREA DISP by pressing [MENU UP], [MENU DOWN] buttons.
㽳Select the desired area by pressing [DATA UP], [DATA DOWN] buttons.
-10 0 10
[DATA UP] ¸Red is increased.
Red is decreased. ¸[DATA DOWN]
-10 0 10
[DATA UP] ¸Blue is increased.
Blue is decreased. ¸[DATA DOWN]
The available picture area is shown by the shading correction on the screen that is divided into 64.
PRESET APRESET BPRESET DPRESET C
PRESET E