Toshiba IK-TU61 User manual

For Customer Use
Enter below the Serial No.
which is located on the
bottom of the cabinet. Retain
this information for future ref-
erence.
Model No.: IK-TU61
Serial No.:
CAMERA CONTROL UNIT
IK-TU61
INSTRUCTION MANUAL
WARNING
This is a Class A of EN55022 product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class Adigital device, pursu-
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
USER-INSTALLER CAUTION: Your authority to operate this FCC verified equipment could be voided if
you make changes or modifications not expressly approved by the party responsible for compliance to
Part 15 of the FCC Rules.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est comforme à la norme NMB-003 du Canada.

SAFETY PRECAUTIONS
Read the following safety precautions carefully before using the product. These instructions
contain valuable information on safe and proper use that will prevent harm and damage to the
operator and other persons. Make sure that you fully understand the following details (indications,
graphic symbols) before proceeding to the main descriptions in this manual.
Indication definitions Graphic symbol definitions
*1: Bodily injury means injuries, burns and elec-
tric shock which does not require hospitaliza-
tion or prolonged treatment.
Warning
• Do not use the product when abnormality occurs.
Use in the abnormal state such as smoke emitting from the product, burning smell, being
damaged by drop, invasion of foreign objects inside the product, etc. , may cause fire and/
or electric shock. Always be sure to disconnect the power plug from the electrical outlet
(socket) at once and contact your dealer.
• Do not install the product where splashing of water may occur, such as outdoor, a
bathroom, etc.
This may cause fire and/or electric shock.
• Do not repair, disassemble and/or modify by yourself.
This may cause fire and/or electric shock.Always be sure to contact your dealer for internal
repair, check and cleaning of the product.
• Keep the rated voltage for the product.
The use of power supply voltage outside the rated voltage may cause fire and/or electrical
shock. Please refer to ”5.CONNECTIONS”.
• Do not put a vessel(s) filled with a liquid (flower vase, etc.).
If a liquid enters the product, a fire and/or electric shock may occur.
• Do not put the product in an unstable, slanting and/or vibrating place.
Drop and/or fall of the product may cause injury.
• Do not touch power or TV antenna cords during a thunderstorm.
This might cause electric shock.
Meaning
Indicates a prohibited action that
must not be carried out. The actual
prohibited action is indicated in the
symbol or nearby graphically or de-
scribed in text.
Indicates a mandatory action that
must be carried out. The actual
mandatory action is indicated in the
symbol or nearby graphically or de-
scribed in text.
Symbol
Meaning
This indicates that ignoring this la-
bel and/or misoperation of the prod-
uct may cause serious personal in-
jury or even death.
This indicates that ignoring this la-
bel and/or misoperation of the prod-
uct may cause personal injury*1 and/
or material damage*2.
Indication
Warning
Caution
*2: Physical damage means extended harm to home, household effects.
- 2 -

Caution
• Follow these cautions when installing.
• Do not put the product on a Inflammable material such as carpet or blanket.
• Do not put the product in a narrow space, since the heat generated by the product may
cause fine.
• Do not put a inflammable material on the product.
If you do not keep above, the heat generated by the product may cause fire.
• Do not put the product in direct sunshine and/or high temperature.
The temperature rise inside the product may cause fire.
• Do not put the product In a moist or dusty place such as a bathroom, a place close to
a humidifier, etc.
This may cause fire and/or electric shock.
• Do not put the product in a moist, soot/and/or dusty place such as a kitchen, etc.
Do not put the product where soot and steam may occur, such as a kitchen, etc. , or in a
dusty place. This may cause fire and/or electric shock.
• Do not shoot the sun with the lens and do not put the lens in the place exposed to an
intensive light, such as sunshine, etc.
Focusing of the light may cause injury of eye and/or fire.
• Do not put the product in your mouth and do not swallow it.
This may cause suffocation and/or injury.
• Ask your dealer to perform a periodical check and internal cleaning.
Dust inside the product may cause fire and/or trouble. For check and cleaning cost, please
consult your dealer.
- 3 -

- 4 -
1．CAUTIONS ON USE AND INSTALLATION ........................................... 6
2．COMPONENTS...................................................................................... 6
3．ITEMS CONTROLLED BY USING ON SCREEN DISPLAY................... 7
4．NAMES AND FUNCTIONS..................................................................... 8
5．CONNECTION........................................................................................10
5.1 Standard Connection .................................................................................................. 10
5.2 Cautions on Connection.............................................................................................. 10
5.3 Connection on Back Panel.......................................................................................... 10
5.3A Connector Pin Assignments..................................................................................... 11
6．OPERATION...........................................................................................12
6.1 Automatic Black Balance............................................................................................ 12
6.2 White Balance............................................................................................................. 13
6.3 Scene File................................................................................................................... 15
6.4 Gain............................................................................................................................. 15
6.5 Shading Correction ..................................................................................................... 16
6.6 Freeze Operation........................................................................................................ 17
7．MODE SETTING BY ON SCREEN DISPLAY ........................................17
7.1 Using the Menus......................................................................................................... 17
7.2 Menus ......................................................................................................................... 19
(1) SHUTTER (Electronic shutter) .................................................................................... 19
(1.1) Changing each setting in AUTO mode................................................................ 20
(1.2) Changing each setting in MANUAL mode........................................................... 22
(1.3) Changing each setting in SS(synchro. scan) mode ............................................ 23
(1.4) Changing each setting in EXT TRIG mode......................................................... 24
(1.4.1) Changing each setting in 1 PULSE SNR mode................................................ 24
(1.4.2) Changing each setting in 1 PULSE SR mode.................................................. 25
(1.4.3) Changing each setting in 2 PULSE mode........................................................ 26
(1.4.4) Changing each setting in RS232C mode ......................................................... 27
(2) GAIN (Video gain) ....................................................................................................... 27
(2.1) Changing the maximum gain in AUTO (Automatic gain control) mode .............. 28
(2.2) Changing gain in MANUAL mode........................................................................ 28
(3) WHT BAL (White balance).......................................................................................... 29
(3.1) Changing the AWB (Automatic White Balance)mode setting............................. 29
(3.2) Changing the ATW (Automatic Trace White Balance)mode setting................... 30
(3.3) Changing the MANUAL mode setting.................................................................. 31
(4) PROCESS (Process)................................................................................................... 32
(4.1) Changing the gamma correction ON/OFF .......................................................... 32
(4.2) Changing gamma correction level....................................................................... 32
(4.3) Changing black gamma correction level ............................................................. 33
(4.4) Changing detail (outline) gain.............................................................................. 33
(4.5) Changing detail boost frequency......................................................................... 33
(4.6) Changing master pedestal .................................................................................. 33
(4.7) Changing chroma gain ........................................................................................ 34
(4.8) Changing DNR(Digital Noise Reduction)............................................................. 34
(5) MATRIX(Matrix color correction)................................................................................. 35
(5.1) Changing MATRIX color correction ON/OFF...................................................... 35
(5.2) Changing each of MATRIX setting...................................................................... 35
(6) SYNC........................................................................................................................... 36
(6.1) INT screen........................................................................................................... 36
(6.2) Changing EXT setting.......................................................................................... 36
TABLE OF CONTENTS

- 5 -
(7) OPTION....................................................................................................................... 37
(7.1) Chaging OUTPUT1 output .................................................................................. 37
(7.2) Chaging OUTPUT2 output .................................................................................. 37
(7.3) Chaging shading correction mode....................................................................... 37
(7.4) Chaging manual shading correction setting ........................................................ 37
(7.5) Chaging RGB SYNC ........................................................................................... 37
(7.6) Chaging FREEZE DISP setting........................................................................... 38
(7.7) Chaging Negative/Positive inversion switch........................................................ 38
(7.8) Chaging detail signal output ................................................................................ 38
(7.9) Chaging RS232C communication baud rate setting ........................................... 38
(8) Setting USER area ...................................................................................................... 38
(9) Setting to factory setting status ................................................................................... 40
7.3 External Sync.............................................................................................................. 40
(1) External sync signal input conditions........................................................................... 40
(2) External sync frequency range.................................................................................... 41
(3) Using the unit with external sync signal....................................................................... 41
(3.1) H (horizontal) phase adjustment ......................................................................... 41
(3.2) SC (Sub carrier) phase afjustment...................................................................... 41
7.4 Synchro. Scan Operation............................................................................................ 42
(1) Setting by 1H............................................................................................................... 42
(2) Setting by the frame .................................................................................................... 42
7.5 EXT TRIG(External trigger) ........................................................................................ 43
(1) 1 PULSE SNR (1 PULSE Sync Non Reset)................................................................ 43
(2) 1 PULSE SR (1 PULSE Sync Reset) .......................................................................... 44
(3) 2 PULSE...................................................................................................................... 45
(4) RS232C....................................................................................................................... 47
7.6 Freeze Operation by Trigger Input.............................................................................. 48
7.7 Digital output............................................................................................................... 49
(1) Sync pulse timing......................................................................................................... 49
8．BEFORE MAKING A SERVICE CALL....................................................50
9．SPECIFICATIONS..................................................................................51
10．EXTERNAL APPEARANCE DIAGRAM................................................52

- 6 -
●Carefully handle the units.
Do not drop, or give a strong shock or vibration
to the camera. This may cause problems.
Treat the camera cables carefully to prevent
cable problems, such as cable breakdown and
loosened connections.
●Do not shoot intense light.
If there is an intense light at a location on the
screen such as a spot light, a blooming and
smearing may occur.
When intense light enters, vertical stripes may
appear on the screen. This is not a malfunction.
Ghosts may occur when there is an intense light
near the object. In this case, change the
shooting angle.
●Install the camera in a location free
from noise.
If the camera or the cables are located near
power utility lines or a TV, etc. undesirable
noise may appear on the screen. In such a
case, try to change the location of the camera
or the cable wiring.
●Moire
When thin stripe patterns are shooted, stripe
patterns that are not actually there (moire) may
appears as interference stripes. This is not a
malfunction.
（1）Camera Control Unit ............................................................................................... 1
（2）Accessories
（a）Instruction manual ........................................................................................1
●Operating ambient temperature and humidity.
Do not use the camera in places where temperature
and humidity exceed the specifications. Picture
quality will lower and internal parts may be
damaged.
Be particularly careful when using in places
exposed to direct sunlight. When shooting in hot
places, depending on the conditions of the object
and the camera (for example when the gain is
increased), noise in the form of vertical strips or
white dots may occur. This is not a malfunction.
●Handling of the camera head and
protection cap.
Keep the camera head and the protection cap away
from children. Children may put them into mouth or
swallow them accidentally. The protection cap
protects the image sensing plane when the lens is
removed from the camera head, do not throw away.
●When not using the camera for a longtime.
Turn off the camera power switch and stop
supplying power.
●When cleaning the camera
Always turn off the power and clean with a piece of
dry cloth. If necessary, gently wipe with a cloth
dampened with thinned detergent. Do not use
benzine, alcohol, thinner, etc. If used, coating and
printed letters may be discolored. When cleaning
the lens, use a lens cleaning paper, etc.
2．
．．
．COMPONENTS
1．
．．
．CAUTIONS ON USE AND INSTALLATION

- 7 -
Item Available selections
Preset value
(Factory setting)
MODE AUTO, MANUAL, SS, EXT TRIG MANUAL
EXT TRIG 1PULSE SNR, 1PULSE SR, 2PULSE, RS232C 1PULSE SNR
AUTO level -100 −0 −100 0
AUTO peak/average 00：10 −05：05 −10：00 05：05
AUTO response speed 1 −5 −10 5
AUTO area PRESET A, PRESET B, PRESET C, PRESET D,
PRESET E, USER
(USER area is possible to set in 64 zones)
PRESET A
MANUAL speed OFF, 1/120s, 1/250s, 1/500s, 1/1000s, 1/2000s,
1/4000s, 1/10000s OFF
Syncro. FLD 1/625H to 310/625H, OFF, 1FRM to 255FRM
scan FRM 1/625H to 310/525H, OFF, 2FRM to 256FRM OFF
Storage mode FLD, FRM FLD
Freeze operation FRONT, TRIG , TRIG FRONT
Trigger
(1PULSE SNR／SR) ,
Trigger(2PULSE) , ,
1PULSE exposure time 0.06ms to 20ms 20ms
AUTO maximum gain 0dB to 20dB 10dB
MANUAL gain 0dB to 20dB 0dB
Color temperature 3200K, 5600K 3200K
AWB R PAINT -10 −0 −10 0
AWB B PAINT -10 −0 −10 0
AWB area PRESET A, PRESET B, PRESET C, PRESET D,
PRESET E, USER
(USER area is possible to set in 64 zones)
PRESET A
ATW R PAINT -10 −0 −10 0
ATW B PAINT -10 −0 −10 0
MANUAL R GAIN -100 −0 −100 0
MANUAL B GAIN -100 −0 −100 0
Gamma correction switching ON, OFF ON
Gamma correction level -10 −0 −10 0
Black gamma LOW, NORMAL, HIGH NORMAL
Detail gain -7(OFF) −0 −7 0
Detail boost frequency LOW, NORMAL, HIGH NORMAL
Master pedestal -50 −0 −50 0
Chroma gain -128 −0 −127 0
Digital noise reduction(DNR) ON, OFF OFF
Correction ON/OFF ON, OFF ON
JK-TU62H use JK-TU63H use
R hue -15 −0 −15 0 0
R gain -15 −0 −15 0 0
G hue -15 −0 −15 3 0
G gain -15 −0 −15 3 0
B hue -15 −0 −15 0 0
B gain -15 −0 −15 2 -1
Ye hue -15 −0 −15 0 0
Ye gain -15 −0 −15 2 -1
Cy hue -15 −0 −15 0 0
Cy gain -15 −0 −15 0 0
Mg hue -15 −0 −15 0 0
Mg gain -15 −0 −15 0 0
Electronic shutter White balance Matrix color correction
3
．
．．
．
ITEMS CONTROLLED BY USING ON SCREEN DISPLAY

- 8 -
Item Available selections
Preset value
(Factory setting)
H phase adjustment -100 −0 −100 0
SC 0/180 0, 180 0
Ext.
Sync. SC phase adjustment -128 −0 −127 0
OUTPUT 1 RGB, Y/PR/PBRGB
2 VBS, Y/C VBS
Shading correction mode SET, MANUAL, OFF OFF
Manual shading correction -128 −0 −127 0
RGB SYNC G, ALL ON, ALL OFF G
FREEZE DISP ON, OFF ON
Negative/Positive inversion NEGA, POSI POSI
Detail signal output ON, OFF OFF
RS232C baud rate 9600bps, 19200bps 9600bps
①Camera cable
terminal
③POWER switch
②POWER LED
④FILE button
⑤FREEZE button
⑥DISP button
⑦PAGE button
⑧MENU UP
(SHD) button
⑨MENU UP(SHD) botton
⑩DATA UP
(AWB) button
⑪DATA DOWN
(ABB) button
⑫DC IN 12V terminal
CAMERA POWER
ON
OFF
FILE DISP
(SHD) (AWB)
FREEZE PAGE
MENU DATA
(ABB)
RGB
KEY LOCK
ON
OFF
DIGITAL
⑬DC IN/SYNC terminal
⑭S-VIDEO terminal
⑮EXT.SYNC terminal
⑯VIDEO terminal
⑰DIGITAL terminal ⑱KEY LOCK switch
⑲RGB terminal
DC IN 12V DC IN/SYNC S-VIDEO EXT SYNC VIDEO
4．
．．
．NAMES AND FUNCTIONS

- 9 -
①Camera cable terminal The camera cable is connected.
②POWER LED Lights when the power is turned on.
③POWER switch Turns on or off the power supply.
④FILE button Used when switching the scene files.
⑤FREEZE button Used when switching to the freeze menu and when returning from the freeze
menu to the camera menu.
⑥DISP button Used when switching the display.
⑦PAGE button Used when switching to the menu and when selecting the menus.
⑧MENU UP（SHD）button Select the function to be confirmed or changed on the menu. (Also used when
performing the auto shading correction.)
⑨MENU DOWN button Select the function to be confirmed or changed on the menu.
⑩DATA UP（AWB）button Changes the value of the function selected by the MENU (UP/DOWN) button.
(Also used when using AWB.)
⑪DATA DOWN
（ABB）button
Changes the value of the function selected by the MENU (UP/DOWN) button.
(Also used when using ABB.)
⑫DC IN 12V terminal Accept a DC power input (12V).
⑬DC IN／SYNC terminal HD and VD signals are input/output. When the random trigger operation is
used, the trigger signal is input and the index signal is output.
⑭S－VIDEO terminal Outputs Y (luminance) and C (color) signals.
⑮EXT. SYNC terminal Used when the camera output signal is synchronized by the external signal.
(BNC connector)
⑯VIDEO terminal Outputs VBS output. Connected to a monitor, VTR, etc. (BNC connector)
⑰DIGITAL terminal LVDS format digital video signal output and control signal input/output
terminal. This terminal also includes an RS232C format external control pin.
⑱KEY LOCK switch Enables/disables buttons ④to ⑪.
⑲RGB terminal Used as the connector terminal for Y/C or VBS output, RGB or Y/PR/PBoutput,
and SYNC output.

- 10 -
Lens
Camera head
（option）
Camera
Control unit
Camera cable
（option）
monitor
DC power
supply
DC IN 12V
VIDE Coaxial
Cable 75Ω
IK-TU61
・Please use only optional camera heads model # JK-TU62H or JK-TU63H with this camera
controller. Use of another head may cause damage.
・When connecting the camera cables, be sure to turn off the camera control unit and
the other equipment connected.
・For DC power supply connecting to DC IN 12V terminal, use Class II DC power supply
approved according to EN60950 in Europe.
(Betrieb nur mit zertifiziertem AC-Adapter nach EN60950)
When camera is used in USA, use UL listed and/or CSA approved ungrounding type
AC adaptor with the specifications described below.
Power supply voltage ：DC12V±10%
Current rating ：More than 830mA, Less than2.5A
Ripple voltage ：Less than 50mV（p－p）
Connector ：HR10A－7P－4S by HIROSE electronics Co. Ltd
Pins 1, 2 ：12V
Pins 3, 4 ：GND
・If the screw on the camera connector portion of the camera cable looses, noise may
appear on the screen. So be sure to tighten the connector fully.
Back panel view
RGB
KEY LOCK
ON
OFF
DIGITAL
DC IN 12V DC IN/SYNC S-VIDEO EXT SYNC VIDEO
1
31
61
91
30
60
90
120
4
3
2
1
5
4
3
21
6
7
8
9
10
11 12
43
21
54321
7
86
9
5
．
．．
．
CONNECTION
5．
．．
．1 Standard Connection
5．
．．
．2 Caution on Connection
5．
．．
．3 Connection on Back Panel

- 11 -
DC IN 12V DC IN/SYNC S-VIDEO RGB
1 +12V
1 GND 1 GND 1 GND(for VBS,Y/C)
2 +12V
2 +12V 2 GND 2 GND(for R/G/B,Y/PR/PB)
3 GND
3 GND(for INDEX) 3 Y 3 R/PROUT
4 GND
4 INDEX 4 C 4 G/Y OUT
5 GND(for HD) 5 B/PBOUT
6 HD OUT 6 VBS/Y OUT
7 VD OUT 7 SYNC OUT
8 GND(for TRIGGER) 8 GND(for SYNC)
9 TRIGGER 9 -/C OUT
10 VD IN
11 HD IN
12 GND(for VD)
DIGITAL
1 R0 (+) 31 R0 (-) 61 GND 91 GND
2 R1 (+) 32 R1 (-) 62 PIXEL CLK (+) 92 PIXEL CLK (-)
3 R2 (+) 33 R2 (-) 63 FRAME EN (+) 93 FRAME EN (-)
4 R3 (+) 34 R3 (-) 64 FIELD ID (+) 94 FIELD ID (-)
5 R4 (+) 35 R4 (-) 65 LINE EN (+) 95 LINE EN (-)
6 R5 (+) 36 R5 (-) 66 TRIGGER D (+) 96 TRIGGER D (-)
7 R6 (+) 37 R6 (-) 67 RESERVE (OUT +) 97 RESERVE (OUT -)
8 R7 (+) 38 R7 (-) 68 GND 98 GND
9 R8 (+) 39 R8 (-) 69 GND 99 GND
10 R9 (+) 40 R9 (-) 70 NC 100 NC
11 G0 (+) 41 G0 (-) 71 NC 101 NC
12 G1 (+) 42 G1 (-) 72 NC 102 NC
13 G2 (+) 43 G2 (-) 73 NC 103 NC
14 G3 (+) 44 G3 (-) 74 NC 104 NC
15 G4 (+) 45 G4 (-) 75 NC 105 NC
16 G5 (+) 46 G5 (-) 76 NC 106 NC
17 G6 (+) 47 G6 (-) 77 NC 107 NC
18 G7 (+) 48 G7 (-) 78 NC 108 NC
19 G8 (+) 49 G8 (-) 79 NC 109 NC
20 G9 (+) 50 G9 (-) 80 NC 110 NC
21 B0 (+) 51 B0 (-) 81 NC 111 NC
22 B1 (+) 52 B1 (-) 82 NC 112 NC
23 B2 (+) 53 B2 (-) 83 NC 113 NC
24 B3 (+) 54 B3 (-) 84 NC 114 NC
25 B4 (+) 55 B4 (-) 85 GND 115 GND
26 B5 (+) 56 B5 (-) 86 GND 116 GND
27 B6 (+) 57 B6 (-) 87 TXD 117 NC
28 B7 (+) 58 B7 (-) 88 RXD 118 NC
29 B8 (+) 59 B8 (-) 89 GND 119 NC
30 B9 (+) 60 B9 (-) 90 GND 120 GND
* When using pins to remote(pins 87 to 89), please consult with your dealer.
Precautions on DIGITAL terminal :
･Interference occurring inside the cable may accidentally activate the Trigger if the TRIGGER D
inputs (pins 66 and 96) are open.
If the TRIGGER D input is not used, the TRIGGER D input pin should be either not connected or
connected to RESERVE output pin (pins 67 and 97) ie: (connect pin 66 to pin 67 and pin 96 to 97).
･The RESERVE pins (pins 67 and 97) are provided for an additional output. If unused they should be
OPEN or connected to Trigger D.
･NC pins (pins 117 to 119) should be left OPEN.
5．
．．
．3A Connector Pin Assi
g
nments

- 12 -
①Referring to the item “ 5. CONNECTION”, connect each equipment correctly.
②Turn on the connected equipment and the camera.
③When using the camera for the first time and when replacing the camera cable and the camera head, be
sure to operate the ABB adjustment in advance, referring to the item “6.1 Automatic Black Balance”.
④Pointing the lens at the object, operate the lens iris adjustment, focus adjustment, etc.
⑤Referring to the item “6.2 White Balance”, operate the adjustment.
⑥Referring to the items “6.3 Scene File, 6.4 Gain, 7. MODE SETTING BY ON SCREEN DISPLAY”, select
the necessary items.
Black balance adjustment is necessary to get the correct black picture level.
・Close the lens iris.
・If the color bar pattern is displayed on the screen or if the index menu/menu is displayed, press the
[DISP] button to disable the color bar pattern or the character display. If the camera is in Freeze Mode,
perform the cancellation procedure (refer to the item “6.6 Freeze Operation”) to return the camera to Live
Image Mode.
・Hold the [DATA DOWN] button for approx. 1 second.
・When the black balance adjustment operation starts, the character ABB blinks on the screen.
・When the black balance adjustment operation finishes, the character ABB ends blinking and the result
appears for approx. 1 second.
Display Meaning
ABB OK Automatic black balance adjustment finished correctly.
ABB NG
CLOSE LENS Automatic black balance adjustment cannot be performed because the lens iris is open. Close the lens iris.
ABB NG Automatic black balance adjustment cannot be performed.
Operate the automatic black balance again.
6
．
．．
．
OPERATION
6．
．．
．1 Automatic Black Balance

- 13 -
For the white balance adjustment for this unit, ATW (Automatic Trace White balance), AWB (Automatic
White Balance) and MANUAL (Manual white balance) adjustments are provided. Referring to the items “7.2
(3) WHT BAL (White balance), 7. MODE SETTING BY ON SCREEN DISPLAY”, select the desired mode.
ATW
（
（（
（Automatic Trace White
Balance）
））
）
AWB
（
（（
（Automatic White Balance）
））
）MANUAL （
（（
（Manual White Balance）
））
）
Outline Camera measures the object
color temperature and
adjust the white balance
automatically.
Adjust white balance by
displaying the white object
inside the area set by AWB
menu and pressing the
[DATA UP] button.
Adjust the white balance
manually using the WHT
BAL menu while shooting
the white object.
Features Traces variations of color
temperature and adjusts
the white balance automati-
cally.
Measurement accuracy is
higher than ATW. This
mode is effective when
shooting under less varia-
tions of color temperature.
Artificial white balance
setting can be set. The
manual adjustment is most
effective under shooting
condition with no color
temperature variation.
Notes If an illumination is low,
white balance may not be
corrected. When the shutter
mode is EXT TRIG or long
the long period exposure
mode, ATW is not available.
When the shutter mode is
EXT TRIG, AWB is not
available.
Adjustment is performed by
confirming with a vector
scope.
①AWB(Automatic white balance)
・Set the MODE to AWB on the WHT BAL menu.
Perform the C.TEMP (color temperature conversion) setting, if necessary.
(Refer to the item “7.2 (3) WHT BAL (White balance)”.)
3200K：Appropriate for indoor shooting.
5600K：Appropriate for outdoor shooting.
・If the color bar pattern is displayed on the screen or if the index menu/menu is displayed, press the [DISP]
button to disable the color bar pattern or the character display on the menu. If the camera is in Freeze
Mode, perform the cancellation procedure (refer to the item “6.6 Freeze Operation”) to return the camera to
Live Image Mode.
・Shoot a known white object that fills the area set by the AWB menu (refer to the item “7.2 (3) (3.1) (d)
Changing AWB zone area” ) and push [DATA UP] button for approx. 1 second.
・The character AWB blinks on the screen when the AWB starts.
・The character AWB stops blinking when the AWB finishes, and the result is displayed for approx. 1 second.
6．
．．
．2 White Balance

- 14 -
Display Meaning
AWB OK Automatic white balance adjustment finished correctly.
AWB NG
LEVEL LOW Automatic white balance adjustment cannot be performed because the video level is
too low.
Set the video level properly.
AWB NG
LEVEL HIGH Automatic white balance adjustment cannot be performed because the video level is
too high.
Set the video level properly.
AWB NG
C．
．．
．TEMP LOW Automatic white balance adjustment cannot be performed because the color
temperature is too low.
If the C.TEMP is set to 5600K, set to 3200K.
If the message appears with the C.TEMP set to 3200K, change the illumination or
use a color temperature conversion filter.
AWB NG
C．
．．
．TEMP HIGH Automatic white balance adjustment cannot be performed because the color
temperature is too high.
If the C.TEMP is set to 3200K, set to 5600K.
If the message appears with the C.TEMP set to 5600K, change the illumination or
use the color temperature conversion filter.
AWB NG
NOT AVAILABLE Automatic white balance adjustment cannot be performed because the shutter speed
mode is EXT TRIG mode.
AWB NG Automatic white balance adjustment cannot be performed for other reasons. Such as
no white area is included in an object, etc.
②MANUAL(Manual white balance)
・Set the MODE to MANUAL on the WHT BAL menu.
(Refer to the item “7.2 (3) WHT BAL (white balance)”.)
・Shoot a known white object, adjust the white balance adjusting the levels of R GAIN and B GAIN on the
menu, confirming with a monitor or a vector scope.
(Refer to the item “7.2 (3) (3.3) Changing each setting in MANUAL mode”.)

- 15 -
Three scene files (A, B, C) are available as user memories for this unit. These are selectable depending on
shooting conditions. By using the [FILE] button, the camera operation is changed immediately from the
currently selected Scene File to the next. (Refer to the item “7. MODE SETTING BY ON SCREEN
DISPLAY”.)
・While any menu is displayed, pressing the [FILE] button will display the menu settings for the next Scene File:
FILEA →
→→
→FILE B →
→→
→FILE C
・When the [FILE] button is pressed while the camera is in live image mode, the current scene file selection
at that time is displayed for approx. 3 seconds in the upper right corner of the screen. If the [FILE] button is
pressed again while the position is displayed, the scene file cycles as described above.
When the image is dark even if the lens iris is open, change the gain (video gain) to get the proper video
level.
For the gain adjustment of the unit, AUTO (Automatic gain control), MANUAL (Manual), OFF (0 dB) modes
are provided. Select the mode on the GAIN menu. (Refer to the item “7.2 (2) GAIN (Video gain)”.)
①AUTO(Automatic gain control)
When the output is low, the gain is automatically adjusted to a suitable video level.
The maximum value of the gain is 20dB, and can be set from 0 to 20dB in 1dB steps. (Refer to the item
“7.2 (2) (2.1) Changing the maximum gain in AUTO (Automatic gain control) mode”.)
Video level (LEVEL), peak average value ratio (PEAK/AVE), and measurement light area (AREA) is same
as the setting on the automatic shutter. (Refer to the item “7.2 (1) (1.1) Changing each setting in AUTO
mode”.)
②MANUAL(Manual gain)
Gain adjustment is performed on the GAIN menu. The adjustment range is from 0 to 20dB in 1dB steps.
(Refer to the item “7.2 (2) (2.2) Changing the gain in MANUAL mode”.)
③OFF
Gain is fixed at 0 dB.
6．
．．
．3 Scene File
6．
．．
．4 Gain

- 16 -
Due to the lens used or the environmental condition, vertical color shading may occur at the top and bottom
of the screen. In this case, the shading correction can decrease the color shading. For the shading correction
of the unit, SET (Automatic shading correction), MANUAL (Manual shading correction), and OFF (no shading
correction) modes are provided. Select the mode on the OPTION menu. (Refer to the item “7.2 (7) (7.3)
Changing shading correction mode”.)
①SET(Auto shading)
・When the shutter speed mode is set to EXT TRIG or the SS long period exposure mode, the automatic
shading correction cannot be performed.
･If the color bar pattern is displayed on the screen or if the index menu/menu is displayed, press the
[DISP] button to remove them from the screen. If the camera is in Freeze Mode, perform the
cancellation procedure (refer to the item “6.6 Freeze Operation”) to return the camera to Live Image
Mode.
・Push the [MENU UP] button for approx. 1 second.
・When the automatic shading correction operation starts, the character SHD blinks on the screen.
・When the automatic shading correction operation terminates, the character SHD ends blinking and the
result is displayed for approx. 1 second.
Display Meaning
SHD OK Automatic shading correction operation terminated correctly.
SHD OK
LIMIT Automatic shading correction operation terminated, however, the correction
necessary exceeds the camera’s range so the maximum possible value is applied.
SHD NG
LEVEL LOW Automatic shading correction cannot be performed because the video level is too
low. Set the video level properly.
SHD NG
LEVEL HIGH Automatic shading correction cannot be performed because the video level is too
high. Set the video level properly.
SHD NG
NOT AVAILABLE Automatic shading correction operation cannot be performed because the shutter
speed mode is the EXT TRIG mode or the SS long period exposure mode.
②MANUAL(Manual Shading)
Perform the correction amount setting on the OPTION menu, confirming with a monitor or a vector scope.
(Refer to the “7.2 (7) (7.4) Changing the manual shading correction setting”.)
③OFF
The status is no shading correction.
*The shading correction is effective when the lens iris or zoom ratio is fixed. Use the unit with
SHADING OFF for variable lens conditions.
6．
．．
．5 Shading Correction

- 17 -
・Freeze Mode Operation is only possible when no menu character display or color bar is on the screen.
・Freeze Mode Operation is not possible when the shutter mode is set to EXT TRIG.
・The method of toggling between Live Image Mode and Freeze Mode differs according to the shutter
menu’s FREEZE INPUT setting.
When set to FRONT ：The mode is toggled using the FREEZE button on the front panel.
When set to TRIG ：The mode is toggled at the rising edge of the trigger terminal input.
When set to TRIG ：The mode is toggled at the falling edge of the trigger terminal input.
・When the OPTION menu’s FREEZE DISP setting is set to ON, “FREEZE” is indicated at the upper right
corner of the screen.
・During Freeze Mode Operation, the [DISP], [PAGE], [MENU UP], [MENU DOWN], [DATA UP], [DATA
DOWN] and [FILE] buttons are disabled.
Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The
contents once set are memorized in the scene files (A, B, C) selected when the power is turned off, so it is
unnecessary to set again when using the unit next time. When the setting is performed, select the menu of
the item to be set.
When the power turns on, the normal screen showing only the video signal appears. Change the output to
each screen (video signal output, color bar screen, Index menu, menus, and area menu) by using the [DISP],
[PAGE], [MENU UP], and [MENU DOWN] buttons.
* A menu is selected when pushing the [PAGE] button after moving the “→” on the screen by the [MENU
UP], [MENU DOWN] button while the Index menu is displayed.
6．
．．
．6 Freeze Operation
7
．
．．
．
MODE SETTING BY ON SCREEN DISPLAY
7．
．．
．1 Using the Menues

- 18 -
USER
USER
EXT TRIG
2 PULSE
EXT TRIG
1 PULSE SR
POWER SW
ON
Video signal output
DISP
PAGE
PAGE
1.SHUTTER 2.GAIN 3.WHT BAL 4.PROCESS 5.MATRIX 6.SYNC
Color bar screen
Menus
Index menu
DISP DISP
PAGE PAGE PAGE PAGE
PAGE PAGE
AUTO
MANU
NORM
ATW ON
OFF
INT
EXTAWB
MANU
GAMMA
ON
GAMMA
OFF
AUTO
MANU
SS
EXT TRIG
1 PULSE SNR
PAGE
DISP
EXT TRIG
RS232C
6.OPTION
PAGE RGB
Y/P
R /P B
Area menu
DATA
UP/DOWN DATA
UP/DOWN
The screen is changed to the area screen by
selecting AUTO in the 1.SHUTTER menu and
AWB in the 3.WHT BAL menu in the setting
screen For more details, refer to the item "7.2
Each menu".
D
A
B
C
E
DISP DISP
D
A
B
C
E
Area menu

- 19 -
・Select the menu to change the setting by referring the item “7.1 Using the Menus”.
・When the [MENU UP], [MENU DOWN] buttons are pushed, the “→” on the screen moves up and down.
Move the “→” to the item to change.
( 1 ) SHUTTER（
（（
（Electronic shutter）
））
）
The electronic shutter has four modes; AUTO, MANUAL, SS(Synchro. Scan), EXT TRIG(External trigger).
Press the “Page” button to enter the Shutter Page. Use the “Data Up/Down” buttons to select the Shutter
Mode.
AUTO MANUAL SS EXT TRIG
AUTO ：The exposure time is controlled automatically to obtain the video level set.
MANUAL ：It is possible to select the exposure time from eight speed settings; OFF (1/50s), 1/120s,
1/250s, 1/500s, 1/1000s, 1/2000s, 1/4000s, 1/10000s.
Note:
When setting a rapid shutter speed, sensitivity degrades according to the speed.
When a discharging light such as fluorescent lamp, etc. is used for the illumination,
the flicker may be large.
SS ：Shutter speed can be set by the horizontal scanning time (1H) unit or by the frame unit.
EXT TRIG ：Exposure is performed and images are output by external trigger. EXT TRIG includes the
four modes described below. (For details of specifications, refer to the item “7.5 EXT TRIG
(External trigger)”.)
●1 PULSE SNR（1 Pulse Sync Non Reset）
The charge begins to accumulate after the trigger pulse is received, and 1 field images are
output according to the internal vertical sync signal timing. The exposure/accumulation time
can be set from 0.06 to 16 ms. The trigger signal timing can be set to either the rising or
falling edge.
●1 PULSE SR（1 Pulse Sync Reset）
The charge begins to accumulate after the trigger pulse is received. Upon completion of
accumulation the vertical sync signal is reset and 1 field images are output. The
exposure/accumulation time can be set from 0.06 to 20 ms. The trigger signal timing can
be set to either the rising or falling edge.
●2 PULSE
The charge begins to accumulate after the trigger pulse is received. Upon completion of
accumulation the vertical sync signal is reset and 1 field images are output. The
exposure/accumulation time is the time from when the first trigger signal is taken in until
the next trigger signal is taken in. The trigger signal intake timing can be set to one of
three settings: rising edge, falling edge or pulse width (front and back edges of pulse).
●RS232C
Accumulation of charges is started and ended by RS232C external control command
input, and 1 field images are output without changing the vertical sync signal timing.
7．
．．
．2 Menus

- 20 -
（
（（
（1．
．．
．1）
））
）Changing each setting in AUTO mode
・Shutter mode AUTO, MANUAL, SS, EXT TRIG
・Video level adjustment -100 to 100
・Peak and average ratio adjustment 00：10 to 10：00
-- 1 SHUTTER -- <FILE A>
・Automatic shutter response speed adjustment 1 to 10
→MODE AUTO
LEVEL 0 ・Automatic shutter area selection
PEAK／AVE 05：05 PRESET A, PRESET B, PRESET C, PRESET D, PRESET E, USER
SPEED 5 ・Automatic shutter area display selection
AREA PRESET A
AREA DISPLAY OFF ・FLD／FRM SW FLD, FRM
FLD／FRM FLD
FREEZE INPUT FRONT ・Freeze operation selection FRONT, TRIG , TRIG
<MODE=AUTO>
Move up and down
By pushing
MENU UP,DOWN
Set by pushing
DATA UP,DOWN
(a) Changing the video level in the automatic shutter mode
①Set the “→” to LEVEL by pushing [MENU UP], [MENU DOWN] buttons.
②Set the video level by pushing [DATA UP], [DATA DOWN] buttons.
→The value increases by pushing [DATA UP]
-100 0 100
←The value decreases by pushing [DATA DOWN]
(b) Changing the automatic shutter detection (ratio between peak and average value)
①Set the “→” to PEAK/AVE by pushing [MENU UP], [MENU DOWN] buttons.
②Set the ratio between peak and average value by pushing [DATA UP], [DATA DOWN] buttons.
(Peak：Average) →The peak value increases by pushing [DATA UP]
00：10 05：05 10：00
←The peak value decreases by pushing [DATA DOWN]
(c) Changing the automatic shutter response speed
①Set the “→” to SPEED by pushing [MENU UP], [MENU DOWN] buttons.
②Set the response speed by pushing [DATA UP], [DATA DOWN] buttons.
→The response speed becomes faster by pushing [DATA UP]
1 5 10
←The response speed becomes slower by pushing [DATA DOWN]