Toshiba ESTiA User manual

OWNER MANUAL
Wireless interface for Air to Water Heat Pump
Toshiba Home AC Control
Please visit the application store on your device
to download and install Toshiba Home AC Control
application.
Toshiba Home AC Control application support
iOS 9.0 or later.
Android : Version 5.0 or later.
Application
Keyword : Toshiba Home AC
Control
About Toshiba Home AC Control
1. Toshiba Home AC control can control system operation by smartphone or tablet (mobile device) via internet
connection.
2. Everywhere control, software run on Cloud system and mobile device can set and monitor system operation.
3. Everyone can control, 1 Wireless interface maximum 5 User (use 1 email register).
4. Multi system control, 1 user can control 10 system.
Note :
1. Wireless interface can register only 1 email address, if register with new email current email will invalid.
2. 1 email address can use for register 5 mobile devices for control same system.
1130492401-1
BOOK_OM_1130492401-1.indd 1BOOK_OM_1130492401-1.indd 1 23/11/2564 BE 14:4423/11/2564 BE 14:44

Installation for Wireless interface.
1. Open cover of Wireless interface and make hole for wire out.
Make hole by tooling,
should no sharp edge
beware wire damage
Open cover
Wire out position
2. Fix on wall or partition following fixing position, connect wire between Wireless interface and Hydro unit.
Hydro unit
2 core shielded cable – 0.5 mm2or more.
Maximum cable length – 50 m
Non polar
Screw fixing position
Terminal block CN01
Terminal block TB04, for remote
controller or Wireless I/F adapter
connection, to Hydro unit.
Hydro unit
Wireless interface
Wireless interface
3. Close cover of Wireless interface
Hydro unit
Wireless interface
Note :
1. Be sure no electrical power before installing this
product.
2. Wireless interface must not be installed in areas as
below
- Direct sunlight or areas exposed to outside
air influences
- Poor ventilation (near windows or other openings)
- External heat sources (above radiators etc.)
- Freezing or refrigerated areas
- Do not install nearly device the can produce
electrical noise such as elevators, automatic door
and etc.
3. Do not modify for any electrical part, it can cause for
malfunction, electric shock or fire.
4. Install area should be covered by Wi-Fi signal from
Router.
5. Wireless interface compatible with router 2.4GHz
band IEEE802.11 b/g/n standard.
6.
Installation level should be 100 mm or more from floor.
7. Operating temperature should not over 55°C.
BOOK_OM_1130492401-1.indd 2BOOK_OM_1130492401-1.indd 2 23/11/2564 BE 14:4423/11/2564 BE 14:44

Installation for Wireless interface.
Open an application and follow register for User registration.
1Tab Register 2Enter email address 3Select country 4Enter user name
@
5Enter password by
6-10 character, combination
of alphabet and number 8Information will submit to
email, click link for confirm
6Check for term and
condition
7Confirm information
Log in to Toshiba Home AC Control application.
1Connect Wireless interface to system and turn
on power supply.
Operation LED = On Green
Wireless LED = On Yellow
Link LED = Off
Power LED = On Green
* Note
1. In case of Wi-Fi router change or e-mail for register change
need to re-process for add Wireless interface again
(need to press SETUP button 1 time for active Access Point
mode).
2. In case of change Wireless interface to use with other AC need
to factory reset (press and hold SETUP 5s) and re-process for
add Wireless interface again.
2Open application and
select Log in
3Enter user name and
password 4Log in successful
BOOK_OM_1130492401-1.indd 3BOOK_OM_1130492401-1.indd 3 23/11/2564 BE 14:4423/11/2564 BE 14:44

Add Wireless interface for control by Toshiba Home AC Control application.
Wireless Adapter Type C
Wireless adapter auto log in.
1Select “Add AC (Adapter)” from both display above. 2Select AC (adapter) connection method.
Add Wireless interface for control by Toshiba Home AC Control application.
35 °C
48 °C
45 °C
3AC (adapter) connect 4Connect with Home Wi-Fi Router
5A/C add finished
WPS mode
Manual input
Operation LED = On Green
Connect successfully
Wi-Fi Router name
Wi-Fi Router Password
Wireless LED = Off
Link LED = Off
Power LED = On Green
BOOK_OM_1130492401-1.indd 4BOOK_OM_1130492401-1.indd 4 23/11/2564 BE 14:4423/11/2564 BE 14:44

Application information.
1. Home screen description.
User XXX
35 °C
48 °C
45 °C
Menu
Weekly schedule
Setting
Add ESTIA
Setting leaving water temperature for
each ZONE for space heating
All ESTIA On/Off
ESTIA Unit On/Off
ZONE space heating On/Off
Domestic Hot Water On/Off
Device is offline
Notification ERROR code
description (pop up)
Current operation of each ZONE
Setting temperature of
Domestic Hot Water
Current operation of
Domestic Hot Water
Sub menu each ESTIA
Operation Setting
Sensor Information
Change Name
Delete Estia
Sub menu ALL ESTIA
Operation Setting
Sensor Information
Delete ESTIA
BOOK_OM_1130492401-1.indd 5BOOK_OM_1130492401-1.indd 5 23/11/2564 BE 14:4423/11/2564 BE 14:44

Submenu
55 °C
55 °C
-7 °C
30 °C
45 °C
Enter operation mode of ALL ESTIA
ESTIA Family House
BOOK_OM_1130492401-1.indd 6BOOK_OM_1130492401-1.indd 6 23/11/2564 BE 14:4423/11/2564 BE 14:44

2. Mode and condition setting.
45 °C
35 °C
48 °C
Enter operation mode of ALL ESTIA
Enter operation mode of each ESTIA
Select ZONE1 / ZONE2 / DHW,
each operation Setting mode open
directly.
BOOK_OM_1130492401-1.indd 7BOOK_OM_1130492401-1.indd 7 23/11/2564 BE 14:4423/11/2564 BE 14:44

3. Function Select Toshiba HOME ESTIA application.
Status Indicator
Compressor / Electrical Back-up Heater /
Water Pumps / Boiler
Lights for operation mode for
which leaving water temperature
is to be changed.
Mode Select / On-Off
AUTO MODE On/Off
(for auto-curve operation: automatic
leaving water temperature setting
function of Air Outdoor temperatures,
for best energy savings)
Leaving water temperature setting
Special feature
Water temperature after
back-up heater
Water temperatures before
back-up heater (TWO sensor)
Ú1 depend on ESTIA Setting
BOOK_OM_1130492401-1.indd 8BOOK_OM_1130492401-1.indd 8 23/11/2564 BE 14:4423/11/2564 BE 14:44

Operation mode selection and merit function
Zone 1, Zone 2
Cooling Heating
Domestic Hot Water temperature
setting
Domestic Hot Water settings
BOOK_OM_1130492401-1.indd 9BOOK_OM_1130492401-1.indd 9 23/11/2564 BE 14:4423/11/2564 BE 14:44

LED wireless adapter and AC ON/OFF control.
Select On/Off
BOOK_OM_1130492401-1.indd 10BOOK_OM_1130492401-1.indd 10 23/11/2564 BE 14:4423/11/2564 BE 14:44

Weekly schedule set.
Day select
Monday - Sunday
Weekly schedule of all ESTIA unit
Weekly schedule set for each unit
Select program for active by tick at select box
Weekly schedule
set and active
Weekly schedule
set but not active
Weekly schedule
not set
Time select
Weekly schedule cancel.
Mode select
BOOK_OM_1130492401-1.indd 11BOOK_OM_1130492401-1.indd 11 23/11/2564 BE 14:4423/11/2564 BE 14:44

Energy monitoring.
ESTIA Family House
All ESTIA
ESTIA Holiday House
Select Room for Energy monitoring
1Select Energy monitoring 2Energy monitoring display
Set cost calculate and currency
Select Energy monitoring display
Export data and send by Email
BOOK_OM_1130492401-1.indd 12BOOK_OM_1130492401-1.indd 12 23/11/2564 BE 14:4423/11/2564 BE 14:44

In case of have some problem can check from Help menu.
BOOK_OM_1130492401-1.indd 13BOOK_OM_1130492401-1.indd 13 23/11/2564 BE 14:4423/11/2564 BE 14:44

Google Assistant
Link account setup and add devices (ACs)
1Click on + mark 2Select Set up device 3Select Works with Google
4Search Toshiba Home AC Control 5Input Username and Password 6Link account finished, show device
Google Assistant command
Command Categorize
English Language
Example command device name is [ZONE 1 or 2 or DHW]
Power control
(ON/OFF)
OK Google, turn on the [ZONE 1 or 2 or DHW].
OK Google, turn off the [ZONE 1 or 2 or DHW].
Mode setting
(Available only for Zone1 and Zone2)
OK Google, set the [ZONE 1 or 2 or DHW] to Cool mode.
OK Google, set the [ZONE 1 or 2 or DHW] to Heat mode.
Temperature setting
OK Google, set the [ZONE 1 or 2 or DHW] temperature to 55 degrees.
OK Google, increase the [ZONE 1 or 2 or DHW] temperature by
5 degrees.
OK Google, decrease the [ZONE 1 or 2 or DHW] temperature by
5 degrees.
Status inquiry OK Google, what is the [ZONE 1 or 2 or DHW] set to ?
BOOK_OM_1130492401-1.indd 14BOOK_OM_1130492401-1.indd 14 23/11/2564 BE 14:4423/11/2564 BE 14:44

Amazon Alexa
Link account setup and add devices (ACs)
1Select More
5Input Username and
Password
9Devices list show
for set up
$Set up finish
6Link account finished
!Set up device
%Check about
device list
7Discover devices
"Choose GROUP for
your device
8Devices found
#Select continue
2Select Skills & Games
3Search
“Toshiba Home AC Control” 4Click ENABLE TO USE
BOOK_OM_1130492401-1.indd 15BOOK_OM_1130492401-1.indd 15 23/11/2564 BE 14:4423/11/2564 BE 14:44

Amazon Alexa command
Command Categorize
English Language
Example command device name is [Bed room]
Power control
(ON/OFF)
Alexa, turn on the [ZONE 1 or 2 or DHW].
Alexa, turn off the [ZONE 1 or 2 or DHW].
Mode setting
(Available only for Zone1 and Zone2)
Alexa, set the [ZONE 1 or 2 or DHW] to Cool mode.
Alexa, set the [ZONE 1 or 2 or DHW] to Heat mode.
Temperature setting
Alexa, set the [ZONE 1 or 2 or DHW] temperature to 55 degrees.
Alexa, increase the [ZONE 1 or 2 or DHW] temperature by
5 degrees.
Alexa, decrease the [ZONE 1 or 2 or DHW] temperature by
5 degrees.
Status inquiry Alexa, what is the [ZONE 1 or 2 or DHW] set to ?
Note :
“The Wireless Adapter must be installed, maintained, repaired and
removed by a qualified installer or qualified service person.”
“De Draadloze adapter moet worden geïnstalleerd, onderhouden,
gerepareerd en verwijderd door een vakbekwame installateur of een
vakbekwame servicemonteur.”
«Ηεγκατάσταση, συντήρηση, επισκευή και αφαίρεση του Ασύρματου
προσαρμογέα πρέπει να γίνεται από καταρτισμένο τεχνικό εγκατάστασης
ήκαταρτισμένο τεχνικό σέρβις.»
“L’adattatore wireless deve essere installato, sottoposto a manutenzione,
riparato e rimosso da un installatore qualificato o da personale di
assistenza qualificato.”
“El adaptador inalámbrico debe ser instalado, mantenido, reparado
y retirado por un instalador cualificado o una persona de manenimiento
cualifidada.”
“Langattoman sovittimen asennus, huolto, korjaus ja poisto on
annettava pätevän asentajan tai huoltohenkilön tehtäväksi.”
“Trådløs-adapteren må installeres, vedlikeholdes, repareres og fjernes av
en kvalifisert installatør eller kvalifisert servicetekniker.”
“Der kabellose Adapter muss von einem qualifizierten Installateur oder
einem qualifizierten Dienstleister installiert, gewartet, repariert oder
ausgebaut werden.”
BOOK_OM_1130492401-1.indd 16BOOK_OM_1130492401-1.indd 16 23/11/2564 BE 14:4423/11/2564 BE 14:44

«L’interface sans fil doit être installée, entretenue, réparée et retirée par
un installateur qualifié ou un technicien qualifié.»
„Bezdrátový adaptér je třeba nainstalovat udržovat, opravovat a nechat
demontovat kvalifikovaným pracovníkem nebo servisním technikem.“
“Bežični adapter smiju instalirati, popravljati i demontirati samo kvalificirani
instalateri ili serviseri.”
„Bezdrôtový adaptér je oprávnený nainštalovať, udržiavať, opravovať
a odstraňovaťlen kvalifikovaný technik alebo kvalifikovaný servisný
pracovník.“
“Den trådlösa adaptern måste installeras, underhållas, repareras och tas
bort av en kvalificerad installatör eller kvalificerad serviceperson.”
“Den trådløse adapter skal installeres, vedligeholdes, repareres og
nedtages af en kvalificeret installatør eller servicetekniker.”
“Klimatyzator adapter sieci bezprzewodowej powinien byćzainstalowany,
konserwowany, naprawiany i zdemontowany przez wykwalifikowanego
instalatora lub wykwalifikowanego serwisanta.”
“O adaptador sem fios deve ser instalado, mantido, reparado e
removido por um instalador qualificado ou pessoal de assistência
qualificado.”
“Безжичният адаптер трябва да се инсталира, поддържа,
ремонтира идеинсталира от квалифицирани специалисти по
инсталация или квалифициран сервизен персонал.”
BOOK_OM_1130492401-1.indd 17BOOK_OM_1130492401-1.indd 17 23/11/2564 BE 14:4423/11/2564 BE 14:44

“Contact dealer and/or service center when equipment is malfunction.”
“Neem contact op met de dealer en/of het servicecentrum wanneer de
apparatuur niet goed werkt.”
«Επικοινωνήστε με τον αντιπρόσωπο ή/και το κέντρο σέρβις σε
περίπτωση δυσλειτουργίας του εξοπλισμού.»
“Contattare il rivenditore e/o il centro di assistenza quando
l’apparecchiatura non funziona correttamente.”
“Póngase en contacto con el distribuidor y/o el centro de servicio cuando
el equipo no funcione bien.”
“Jos laitteessa ilmenee vikaa, ota yhteyttä jälleenmyyjään ja/tai
huoltoliikkeeseen.”
“Kontakt forhandler og/eller servicesenter når det oppstår feil på utstyret.”
„Wenden Sie sich an den Händler und/oder das Servicezentrum, wenn
das Gerät nicht funktioniert.“
«En cas de dysfonctionnement de l’équipement, veuillez contacter le
revendeur et/ou le centre de service.»
„Kontaktujte prodejce a/nebo servisní středisko v případěporuchy
zařízení.“
“U slučaju kvara na uređaju obratite se distributeru ili servisnom centru.”
„Ak je zariadenie nefunkčné, obráťte sa na predajcu alebo servisné
centrum.“
“Kontakta återförsäljaren och/eller servicecenter om utrustningen fungerar
felaktigt.”
“Kontakt forhandler og/eller servicecenter, når udstyret fejler.”
„W przypadku awarii sprzętu skontaktuj sięze sprzedawcąi/lub centrum
serwisowym.”
“Contacte o seu distribuidor e/ou o centro de reparações quando o
equipamento tiver alguma avaria.”
“Свържете се стърговеца и/или сервизния център при неизправност
воборудването.”
BOOK_OM_1130492401-1.indd 18BOOK_OM_1130492401-1.indd 18 23/11/2564 BE 14:4423/11/2564 BE 14:44

BOOK_OM_1130492401-1.indd 19BOOK_OM_1130492401-1.indd 19 23/11/2564 BE 14:4423/11/2564 BE 14:44

BOOK_OM_1130492401-1.indd 20BOOK_OM_1130492401-1.indd 20 23/11/2564 BE 14:4423/11/2564 BE 14:44