TouchTunes Allegro MX-1 Quick start guide

1 of 6
About This Document
This document is intended for:
• Operators of TouchTunes Allegro MX-1 digital jukeboxes.
• TouchTunes Field Service, Customer Support, and Sales personnel.
It describes how to install and troubleshoot the Service Light kit for the Allegro MX-1.
Overview
The Allegro MX-1 accommodates a service light kit (PN 600098-001) that plugs into the main wiring harness and
illuminates the interior of the cabinet, facilitating servicing in low-light situations.
Figure 1 Service Light Kit, Front and Rear Views
When the door of the Allegro MX-1 is opened, components mounted on a circuit board in the interior of the cabinet
activate a panel of high-intensity LEDs that are pointed toward the service tray, providing illumination to the interior.
When the door is closed, the high-intensity LEDs are turned off automatically, unless the small bypass switch on
the control board has been depressed to keep it on permanently (available only on the 300405-001 model).
Mounted on the board is a small emitter and an infrared photo receiver.
•The LED shines an invisible infrared light through the light pipe on to a reflective strip mounted on the cabinet
door above the payment acceptors.
Installation Notes
Allegro MX-1 Service Light Kit
July 2010
900322-001 Rev 01
emitter and I/R
receiver
LEDs
circuit board

2 of 6
•The infrared photo receiver detects the reflected light, which instructs it to keep the service light off.
•When the door is opened, the infrared photo receiver no longer receives the reflected light, and the service light is
turned on.
Figure 2 Service Light Board
Note: To ensure proper continued operation of the service light component, TouchTunes recommends that you keep this
reflective surface clean when making a service call.
Unpacking and Checking Components
The TouchTunes service light kit ships in a single box. If any component appears to be damaged, do not attempt to use or
install the system. Notify TouchTunes or your local distributor immediately.
Verify that you have received the following components with kit 600098-001:
Qty. Description P/N
1 Service light board assembly 300405-001
1 Installation notes (this document) 900322-001
Emitter
Infrared photo receiver

3 of 6
Installation
Installing the Service Light Board
1. Unlock and open the front door of the Allegro MX-1.
2. Open the service tray on the rear of the cabinet, extending it to the full length of its travel.
Figure 3 Opening Door and Service Tray
3. Working from the rear of the cabinet, locate the 4 PCB board supports for the service light board on the rear of
the front cross member.
Figure 4 Service light PCB board supports
Note: You may be more comfortable installing the service light board by reaching in from the front of the cabinet.
Choose the method that is best suited to you.

4 of 6
4. Align the holes on the service light board with the 4 PCB board supports and press it onto the supports until the service
light board is firmly seated on all 4 PCB board supports.
Figure 5 Mounting the Service Light Board
Important: The service light board must be properly seated on the PCB board supports, otherwise cross-talk between the
LED and photo transistor may occur, hampering the operation of the service light kit.
Cross-section Showing Proper Installation
5. Locate the small power connector from the squid cable and connect it to the 3-pin J4 power connector on the service
light board.
Figure 6 Connecting Power From Wiring Harness
Light board
Cross member
on cabinet
J4

5 of 6
6. Ensure that there is an adhesive reflector strip on the inside of the door and that it aligns with the two light pipes
when the door is closed.
Figure 7 Verifying the Reflective Strip
Testing the Installation
1. With the cabinet door and service tray still open, examine the state of the LEDs in the interior of the cabinet.
The LEDs should be illuminated.
2. Close the door of the cabinet and wait ten seconds.
3. From the rear of the cabinet (through the open service tray access), observe the state of the service lighting
LEDs.
The LEDS should be extinguished.

Copyright © 2010 TouchTunes Interactive Networks
TouchTunes Interactive Networks
400 Sainte Croix Avenue, Suite 200 E
Montreal, Quebec H4N 3L4
Canada
TouchTunes Interactive Networks
3455 Salt Creek Lane, Suite 100
Arlington Heights, IL 60005
USA
Technical Support
847-353-1954
www.touchtunes.com
6 of 6
Troubleshooting
Use the following table to assist you in troubleshooting your service light kit installation.
If you fail to resolve your problem after attempting the above steps, consult TouchTunes for further assistance.
Contacting TouchTunes Support
If you need help with or have questions about this document, contact TouchTunes by:
•Using the email links on the Contacts page on the TouchTunes Dashboard at https://operator.touchtunes.com.
•Calling TouchTunes 24/7 Service Hotline at 847-353-1954.
To help us assist you more effectively with problem reports, the following information may be required when
contacting TouchTunes Support:
•Jukebox ID or PlayPorTT ID.
•Jukebox model (e.g., Allegro MX-1).
•The serial number of any component you believe to be defective.
•The date/time of the problem.
•Actions performed immediately before the problem occurred.
•Any additional comments.
If you require assistance with this or any other TouchTunes product, please call or email technical support. We
value your comments.
Symptom Possible causes Solutions
Service light does not illuminate
when door is opened.
Power from harness not properly
connected.
Check connection from wiring harness to
service light board.
Service light remains on when
door is closed.
Board not properly seated on all
4 PCB board supports.
Check that board is properly seated on all 4
PCB board supports.
Some boards (PN 300405-001)
are equipped with a bypass
switch for keeping the light on
even when the door is closed,
and this switch is depressed.
Press the switch on the board to turn the
light off.
PCB board supports not firmly
seated in cross member of
cabinet.
Check that all 4 PCB board supports are
seated firmly in their mounting holes.
The service light can take up to
10 seconds to turn off.
Wait a few seconds longer and observe the
status of the lights.