Town & Country Fireplaces TC42.NG06C User manual

020511-16 TC42.NG06C 5056.426C1A
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
These instructions are supplementary to the Installation and
Operating Instructions supplied with the replace and should be kept
together.Refer to the Installation and Operating Instructions for proper
gas supply, safety requirements and operating instructions
TC42
CHALET II
BURNER KIT
INSTALLATION
INSTRUCTIONS
PART# TC42.NG06C
For use with:
Model TC42
Series C

2
TC42.NG06C 020511-16
Contents of Package
• BURNER ASSEMBLY
• LOG GRATE
• TC36 LOGS
• EMBER MATERIAL
• HARDWARE PACKAGE
Burner Installation
1. Place the keyhole slots in the burner
over the two screws located in the rebox
base. (Fig. #1 & 1a)
2. Slide the burner back to engage the
screws in the small part of the keyhole
slot and tighten screws. (Fig. #1b)
3. Remove access cover from side of
rebox(Fig. #1c)
Fig. # 1a
Fig. # 1b
SCREWS
Fig. # 1
Fig. # 1c
If this replace is to be
used on Propane please
convert prior to installtion.
See pages 9 – 11.

3
TC42.NG06C 020511-16
BULKHEAD PLATE
2 SCREWS
4. Secure the electrical bulkhead plate and
gasket to the rebox. (2 screws) Attach the
ignition and sensor wires to the module.
Red end to the connector marked by the
red dot, white end to the connector marked
by the white dot
Fig.#2 & Fig.#3
Fig. # 2
Burner/ Grate Installation
RED END TO
RED DOT
WHITE END TO
WHITE DOT MODULE
Fig. # 3

4
TC42.NG06C 020511-16
PILOT SUPPLY
TUBE
MAIN GAS SUPPLY
TUBE
Fig. # 5
5. Attach the pilot and gas supply tubes to
the bulk head tting and tighten.
(Fig. # 4) Ensure the connections are
gas tight. Conceal the spark and
sensor wires below the supply tubes.
A panel set must now be installed. See
Installation and Operating Instructions
manual for details.
6. Position the slots of the grate securing
brackets over the holes in the oor shield
and secure with the two screws
(Fig. # 5).
Fig. # 4

5
TC42.NG06C 020511-16
Ember Material Placement
LOG
GRATE
GLOWING EMBERS
Ember Material
A large bag of ember material is shipped
with the replace and needs to be
installed on the burner to ensure optimum
performance and ame appearance.
1. Pull apart the material into ember size
pieces (approximately 1” squares) and
gently place them into the burner pan.
Do not compress, leave them loose for
best performance.
2. Fill the burner pan level with the top of
the pan at rear, and gradually sloping
forward down to the rebox oor at the
front, covering both burner tubes.
3. Place remaining ember material outside
of the burner pan as desired to cover-up
gas lines and brackets.
Note: Ember material placement and
amount will affect ame appear-
ance. More ember material results
in lower flame height. Add or
remove as needed until desired
ame affect.
Fig. # 6
Gas plumbing and vent connections should
be completed before proceeding.
The logs are are fragile and should be
handled with care. Unpack and inspect
log set. There should be a total of 7 logs.
Position the logs as indicated by the following
pictures. Place the rear log back against the
tabs located at the back of the grate. Place
left log as pictured, engaging the pins with
corresponding holes on the underside of
the log. Install the right log into the grate
and pull it forward into position as shown.
Place the four remaining small logs on the
oor of the rebox in the positions and order
as shown.
Log Set Assembly
Fig. # 7
LOG #1

6
TC42.NG06C 020511-16
Fig. #9
Fig. # 8
LOG #2
LOG #3

7
TC42.NG06C 020511-16
Fig. #11
Fig. #10
LOG #4
LOG #5

8
TC42.NG06C 020511-16
Fig. #13
LOG #7
Note: Improper placement of logs will
cause sooting on internal parts and
glass.
Fig. #12
LOG #6

9
TC42.NG06C 020511-16
Propane Conversion
If the unit is to be used on propane,
convert as follows using the
components supplied with this
burner:
CAUTION
The gas supply and electrical power
must be shut off before proceeding
with the conversion.
Fig. # 15
Fig. # 16
Fig. # 14
WARNING
This conversion kit shall be
installed by a qualied
service agency in
accordance with the
manufacturer's instructions
and all applicable codes
and requirements of the
authority having
jurisdiction.
If the information in these
instructions is not followed
exactly, a re, explosion or
production of carbon
monoxide may result
causing property damage,
personal injury or loss of
life.
The qualied service
agency is responsible for
the proper installation of
this kit.
The installation is not
proper and complete un-
til the operation of the
converted appliance is
checked as specied in the
manufacturer's instructions
supplied with the kit.
1. Ensure the burner, pilot and gas
supply are turned off, and the
appliance has cooled.
2. Remove the two screws securing the
manifold assembly to the burner.
(Fig. #14)
3. Remove the manifold assembly from the
burner. (Fig. #15)
4. With a ½”wrench remove the natural gas
orice (#25) and replace with propane
orice (#332) (our part # 5021.31)
(Fig. #16)
5. Fully open the primary air shutter.
6. Reinstall the manifold assembly
Note: Factory supplied components must
be used to ensure correct input.
After conversion conrm proper manifold
pressure.
MAIN BURNER
(#332) ORIFICE (5021.31)
MINIMUM RATE SCREW (5005.016)
CONVERSION LABEL (5052.5206C)
LP GAS/
DU GAZ LP
12.5 in/wc /12.5 po/c.e.
(3.11 kPa)
13.9 in/wc / 13.9 po/c.e.
(3.45 kPa)
11.0 in/wc / 11.0 po/c.e.
(.95 kPa)
3/32” (2.38 mm)
Max.: 61,000 (17.9)
Min.: 46,200 (13.5) 260411 6-TC42C 5052.5206C
Date: ______________________
By / Par: ___________________
Kit # TC42.LPKTB/EB/EC for use with model:
Pour utilise avec du modèle:
This appliance was converted
to PROPANE GAS with this
kit on this date by the or-
ganization which accepts the
responsibility that this conver-
sion has been properly made.
/ Cet appariel etair converter
au gaz LP par l’emploi de la
trousse de conversion par une
organization qui accepte la
responsibilité pour une instal-
lation en bon état.
TC42
Series C

10
TC42.NG06C 020511-16
Minimum
rate screw
7. With a 7/16”wrench loosen the pilot head
on the pilot assembly by a half-turn
(Fig. #17)
8. Slide the pilot adjustment band over and
ensure that the hole in the orice band is
showing. (Fig. #19 shows NG position,
Fig. # 20 shows LP position)
9. Remove the minimum rate screw located
in the valve.
(Fig. #21)
Fig. #20
Fig. # 21
Fig. # 17
Fig. # 19
M
r
a
HOLE

11
TC42.NG06C 020511-16
LP GAS/
DU GAZ LP
12.5 in/wc /12.5 po/c.e.
(3.11 kPa)
13.9 in/wc / 13.9 po/c.e.
(3.45 kPa)
11.0 in/wc / 11.0 po/c.e.
(.95 kPa)
3/32” (2.38 mm)
Max.: 61,000 (17.9)
Min.: 46,200 (13.5) 260411 6-TC42C 5052.5206C
Date: ______________________
By / Par: ___________________
Kit # TC42.LPKTB/EB/EC for use with model:
Pour utilise avec du modèle:
This appliance was converted
to PROPANE GAS with this
kit on this date by the or-
ganization which accepts the
responsibility that this conver-
sion has been properly made.
/ Cet appariel etair converter
au gaz LP par l’emploi de la
trousse de conversion par une
organization qui accepte la
responsibilité pour une instal-
lation en bon état.
TC42
Series C
NG LP
Fig #24
Fig #25
Fig #23
Minimum
rate screw
Fig #22
Fig #24a
ADD NAME
M
inimum
a
te screw
10. Replace the minimum rate screw with the
one provided in the propane conversion
kit supplied with this replace. Ensure
that the screw is fully installed.
(Fig. #22)
11. Pull off the aluminum cap from the top
of the pressure regulator. (Fig. #23)
12. Press down on the center post and
rotate 90°. The center post should
stay down. (Fig. #24). Replace the
aluminum cap.
13. Fill in the date and the name of the
person who performed the conversion in
the white area on the conversion label.
Peel off the protective backing and apply
the conversion label directly over the
gas specications on the rating label.
14. Attach the access panel to the side of
the rebox with the previously removed
screws. (Fig. #25)
Note:
Gasket must be installed with access
panel.
ADD DATE

12
TC42.NG06C 020511-16
1. Remove the plug from the manifold test
port. The plug is located between the
right side lintel and rebox side (bottom
port). (Fig. # 26)
2. Thread the extension test tting into the
open test port. (Fig. #27)
3. Attach a pressure gauge onto the
tting.
4. When testing is complete remove the
extension test tting and replace the
plug. Thread sealant will be required to
ensure a gas-tight connection.
Correct gas pressure requirement:
Supply Pressure Natural Gas Propane
(For purpose of input adjustment)
Minimum 5.0" WC 12.5" WC
Maximum 13.9" WC 13.9" WC
Manifold Pressure
Maximum 3.8" WC 11.0w" WC
Minimum 2.1" WC 5.5" WC
Note:To test the gas pressure, turn off the gas supply before removing the plug from
the supply pressure test port or manifold pressure test port.
Verify gas pressures with the replace lit and on the highest setting.
Fig #26
Fig #27
Gas Pressure Check

13
TC42.NG06C 020511-16
Fig. # 28
The air shutter on the burner tube controls the primary combustion air to the gas burner
and is preset at the factory for natural gas fuel. Some adjustment may be necessary to
obtain desired ame and to eliminate carbon deposits. Evaluate ame appearance after
the replace has reached operating temperature. See Fig. #28 for proper ame pattern.
Open primary air shutter if the logs, glass, and rebox have carbon accumulation and / or
the ames are long, dark and stringy.The shutter may also be opened to enhance the Ember
Material glow and lessen the ame height.
Caution: Burner area may be hot!
Turn off the replace and allow the unit to cool before proceeding.
Caution: Proper air shutter setting is a
must.
The ame should be just orange and “lazy”.
It should NEVER be set to create sooting on
internal parts and glass.
Burner Flame Adjustment
To Adjust: (Fig. #29)
1. Open and remove window frame and set
aside.See "Window Frame Removal" sec-
tion found in the Installation and Operating
Instructions manual.
2. Remove the log set and set aside.
3. Loosen the screw in the Primary Air
Shutter.
4. Rotate the shutter to increase or decrease
the amount of primary air.
5. Reassemble in reverse order.
Fig. # 29
PRIMARY AIR SHUTTER

14
TC42.NG06C 020511-16
Replacement Parts
ITEM.......DESCRIPTION............................................PART NO.
#1..........BURNER ASSEMBLY......................... TC42.NG06C
#2..........7 PCS LOG SET(TC42)...................... 5094.42161
#3..........ORIFICE, NATURAL GAS (#25)......... 5022.12
ITEM.......DESCRIPTION............................................PART NO.
#4..........PILOT ASSEMBLY.............................. TCRP.5005025
#5..........MAIN SUPPLY TUBE (FLEX) ............. 5019.223
#6..........PILOT TUBE (FLEX).......................... 5019.225
#7..........PROPANE CONVERSION KIT........... TC42.LPCEO1
#1.... BURNER ASSEMBLY
1a GRATE
1b
BURNER INSULATION
1c BURNER TRAY SUPPORT SHIELD
1d PILOT SHIELD
1e TC42.NG01 BURNER WELD
1f MANIFOLD
1g 1/2 PIPE TO 1/2 TUBE CONNECTION
1h PILOT BRACKET
2a LOG #1
2b LOG #2
2c LOG #3
2d LOG #4
2e LOG #5
2f LOG #6
2g LOG #7
KIT CONTENTS:
3 ORIFICE, NATURAL GAS
4 PILOT ASSEMBLY
5 MAIN SUPPLY TUBE
6 PILOT TUBE
#2.... 7 PCS LOG SET
EMBER MATERIAL (Not shown)
2a
LOG #1
2b LOG #2
2c LOG #3
2d LOG #4
2e LOG #5
2f LOG #6
2g LOG #7
#3.... ORIFICE, NATURAL GAS (#25)
#4.... PILOT ASSEMBLY, CONVERTIBLE
#5.... MAIN SUPPLY TUBE (FLEX)
#6.... PILOT TUBE (FLEX)
#7.... PROPANE CONVERSION KIT (Not shown)
(WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION)
*
NOT SHOWN
*
2a
2b 2c
2d 2g
2e
2f
#1
#2 #3
#4
#6 #5
1a
1b
1e
1d
1f
1h
1c 1g

15
TC42.NG06C 020511-16

TECHNICAL SUPPORT: 1-250-748-1184
www.townandcountryreplaces.net
2975 Allenby Rd., Duncan, BC V9L 6V8
Printed in Canada