Toyota PT546-52080 User manual

SCION xB 2008 - XM SATELLITE RADIO
Preparation
Page 1 of 21 pages DIO
Issue:A 02/28/07
Part Number: Mounting Kit PT546-52080
Tuner Assy 86180-0W030 NOTE: Part number of this accessory may not be the
same as the part number shown.
Tuner Assy Kit Contents (86180-0W030)
Item # Quantity Reqd. Description
1 1 Tuner Assy, Stereo Component
Mounting Kit Contents (PT546-52080)
Item # Quantity Reqd. Description
1 1 Ground Cable
2 1 Wire, To Radio Installation
3 2 Tuner Bracket
4 2 Base Bracket
5 1 Template A
(to locate base bracket)
6 4 Cushion A (Butyl)
7 1 Antenna
8 3 Hardware Bags
9 1 XM Satellite Radio Brochure
Hardware Bag Contents – 1 (PT546-52080)
Item # Quantity Reqd. Description
1 4 Screw (M5xL8)
2 4 Nut (M6)
Hardware Bag Contents – 2 (PT546-52080)
Item # Quantity Reqd. Description
1 15 Lock Tie A (AVC-LAN)
2 2 Cushion Tape (50 x 100 mm)
Hardware Bag Contents – 3 (PT546-52080)
Item # Quantity Reqd. Description
1 1 Template B
2 1 Connector Housing
3 1 Cushion Tape (20 x 100 mm)
4 8 Lock Tie B (antenna cable)
5 10 Sheet Tape (to fix antenna)
6 1 Cord Rail (30 mm)
7 3 Protective Sheet (20 x 40 mm)
Additional Items Required For Installation
Item # Quantity Reqd. Description
1 1 Satellite Receiver Cover P/N
PT218-52071
Conflicts
Recommended Tools
Personal & Vehicle
Protection Notes
Safety Goggles
Seat Covers
Special Tools Notes
Arch (Carpet) Punch 5/16 in. Hole Diameter
Installation Tools Notes
Ratchet
Extensions
Sockets 10 mm, 12 mm, 14 mm
Torque Wrench 4.1 N•m (36 lbf•in), 18 N•m (13
lbf•ft), 37 N•m (27 lbf•ft), 42
N•m (31 lbf•ft)
Screwdriver Philips, #2
Panel Removal Tool e.g. Panel Pry Tool #1
Toyota SST # 00002-06001-01
Masking Tape (2 in. wide)
Mallet
Special Chemicals Notes
Sealant 3MTM Ultra-Pro Body
Sealant
Cleaner 3MTM Prep Solvent 70
General Applicability
Recommended Sequence of Application
Item # Accessory
1 TVIP
2 Satellite Receiver
3 Audio
4 Subwoofer (SB) *Mandatory
Vehicle Service Parts (may be required for reassembly)
Item # Quantity Reqd. Description
Legend
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
CAUTION: A process that must be carefully observed
in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.
TOOLS & EQUIPMENT: Used in Figures calls out the
specific tools and equipment recommended for this
process.
REVISION MARK: This mark highlights a change in
installation with respect to previous issue.

SCION xB 2008 - XM SATELLITE RADIO
Preparation
Page 2 of 21 pages DIO
Issue:A 02/28/07
Parts Description of Tuner Assy (86180-0W030)
Parts Description of Mounting Kit (PT546-52080)
Item # Parts Name Qty
1 Ground Cable 1
2 Wire, To Radio Installation 1
3 Cushion Ta
p
e
(
50 x 100 m
m
)
(
0 used for xB
)
2
4 Lock Tie A
(
AVC-LAN
)
15
5 Tuner Bracke
t
2
6 Base Bracket 2
7 Nut (M6) 4
8 Screw (M5 x L8) 4
9 Template A (to locate bracket) 1
10 Cushion A (Butyl) 4
A Antenna 1
B Connector Housing 1
C Template B 1
D Cushion Tape (20 x 100 mm) 1
E Lock Tie B (antenna cable) 8
F Sheet Tape (to fix antenna) (8 used for xB) 10
G Cord Rail (30 mm) 1
11
H Protective Sheet (20 x 40 mm) 3
Item # P arts Name Parts No. Qty
1 Tune
r
86180-0W030 1
12345
6789 10
11
A B C DE
FG H

SCION xB 2008 - XM SATELLITE RADIO
Procedure
Page 3 of 21 pages DIO
Issue:A 02/28/07
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation.
These guidelines can be found in the "Accessory Installation Practices" document.
This document covers such items as:-
•Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).
•Safety (eye protection, rechecking torque procedure, etc.).
•Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).
•Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).
Please see your Toyota dealer for a copy of this document.
NOTES
Removed Parts:
Place all removed parts on a protected surface.
Connectors:
When disconnecting connectors, do not pull on
the wires; pull on the connectors.
Lock Ties:
When using lock ties to secure harness, clip the
lock ties after securing them.
Machine Screws:
Start all machine screws by hand.
Back door lock cannot be released without
reconnecting negative battery cable.
1. Vehicle Disassembly
(a) Remove the negative battery cable.
(Fig. 1-1)
(1) Protect the fender before starting.
(2) Do not touch the positive terminal with
any tool when removing cable.
(b) Remove the deck board and under tray from
the cargo area. (Fig. 1-2)
(c) Remove the four (4) nuts and then remove
both deck floor boxes. (Fig. 1-3)
NOTE: A claw is attached to the right deck
floor box. When removing the box,
detach the claw by pushing the lower
part of the box outward as shown in the
illustration.
Fig. 1-1
Batter
y
Negative
Battery
Cable
10 mm Socket, Ratchet
Fig. 1-3
Nuts x4 Claw
10 mm Socket, Ratchet, Extension
Deck Floor Boxes Claw
Fig. 1-2
Deck Board
under Tray
Deck Boar
d
STOP
STOP
STOP
STOP
STOP
STOP

SCION xB 2008 - XM SATELLITE RADIO
Procedure
Page 4 of 21 pages DIO
Issue:A 02/28/07
(d) Disengage two (2) claws and four (4) clips,
then pull upward and remove the deck trim
cover. (Fig. 1-4)
(e) Disassemble the rear seat as follows:
(1) Disengage the three (3) hooks and
remove the rear seat cushion. (Fig. 1-5)
(2) Remove the rear center seat belt
installation bolt. (Fig. 1-6)
NOTE: Be careful not to scratch or damage the
vehicle body with the seat belt
components. Apply masking tapes
around the metallic parts of the seat
belt.
(3) Fold down the seatback, and then fold
back the cover to locate the two (2)
bolts.
(4) Unbolt and remove the right rear
seatback. (Fig. 1-7)
NOTE: Be careful not to damage the seat, the
door, and other vehicle parts when
removing the seat from the vehicle.
Fig. 1-4
Panel Removal Tool
Claws x2
Clips x4
Fig. 1-5
Hooks x3
Fig. 1-6
14 mm Socket
,
Ratchet
,
Extension
Rear Center
Seat Belt
Seat Belt Bolt
Fig. 1-7
14 mm Socket
,
Ratchet
,
Extension Bolts x2
STOP
STOP

SCION xB 2008 - XM SATELLITE RADIO
Procedure
Page 5 of 21 pages DIO
Issue:A 02/28/07
(f) Disengage the six (6) claws and remove the
rear passenger side door scuff plates.
(Fig. 1-8)
(g) Remove the passenger side deck trim side
panel as follows (Fig. 1-9):
(1) Remove the service hole cover.
(2) Remove two (2) bolts A to detach the
luggage compartment trim hooks.
(3) Remove the clip.
(4) Remove the bolt B and rear seatback
hinge.
(5) Disengage the clips and claws, then
remove the deck trim side panel.
(Fig. 1-10)
(h) In order to prevent scratches, apply
masking tape around the right side rear
combination light before removing it.
(Fig. 1-11)
Fig. 1-9
Panel Removal Tool, 10 mm Socket
12 mm Socket
,
Ratchet
,
Extension Claws x5
Rear Seatback
Hinge
Trim Hooks
Service Hole Cover
Bolts A x2
Clip x1
Fig. 1-8
Panel Removal Tool
②
①Claws A
x2
Claws C
x2
①①
②
Claws A x2
Claws B x2
Fig. 1-11 Masking Tape
Fig. 1-10
Panel Removal Tool
Clips x3
Claws x5
Clips x3
Bolt B

SCION xB 2008 - XM SATELLITE RADIO
Procedure
Page 6 of 21 pages DIO
Issue:A 02/28/07
(i) Disconnect the connector and remove the
three (3) nuts, then detach the right side rear
combination light. (Fig. 1-12).
(j) Disengage the seven (7) claws and remove
the front passenger side door scuff plates.
(Fig. 1-13)
(k) Disengage the clip and the claw, then
remove the passenger side cowl side trim.
(Fig. 1-14)
(l) Disassemble the passenger front seat belt as
follows (Fig. 1-15):
(1) Remove the passenger front seat belt
anchor cover.
(2) Unbolt and detach the passenger front
seat belt anchor plate.
Fig. 1-12
10 mm Socket, Ratchet, Extension
Nuts x3
Clip x1
Connecto
r
Fig. 1-13
Panel Removal Tool
②
①
Claws A
x2
Claws C
x2
①
①
②
Claws B x3
Claws A x2
Fig. 1-14
Panel Removal Tool
Claw x1
Clip x1
Fig. 1-15
14 mm Socket
Ratchet, Extension
Bolt
Claws x2

SCION xB 2008 - XM SATELLITE RADIO
Procedure
Page 7 of 21 pages DIO
Issue:A 02/28/07
(m) Disengage the nine (9) claws and two (2)
clips, then remove the passenger side
lower center pillar garnish. (Fig. 1-16)
2. Remove the Radio/Player Head Unit
(a) In order to prevent scratches, apply
masking tape around the audio cluster
(shaded areas in the figure) before
removing the audio cluster. (Fig. 2-1)
(b) Disengage the four (4) clips and the three
(3) claws, then remove the audio cluster.
(Fig. 2-2)
(c) Disengage the two (2) clips and remove the
audio cluster under plate. (Fig. 2-3)
Fig. 1-16
Panel Removal Tool
Claws x3
Claws x3
Cli
p
s x2
Claws x3
Fig. 2-1 Masking Tape
Audio Cluste
r
Fig. 2-2 Panel Removal Tool
Clips x4
Claws x3
Fig. 2-3 Panel Removal Tool
Cli
p
s x2

SCION xB 2008 - XM SATELLITE RADIO
Procedure
Page 8 of 21 pages DIO
Issue:A 02/28/07
(d) Remove the four (4) bolts and remove the
head unit (Fig. 2-4).
(e) Disconnect the connectors.
3. Remove the Glove Compartment Door
(a) Disconnect the damper from the glove
compartment door.
(b) Squeeze both ends of the box together to
fully extend the box, and then remove the
stoppers. (Fig.-3-1)
(c) Disengage the two (2) claws, and then
remove the glove compartment door.
4. Remove Front Passenger Seat
(a) Protect the rear seat area, the floor, and the
center console area.
(b) Remove the screw and then disengage the
claws and remove the seat track bracket
covers. (Fig. 4-1)
(c) Remove the two (2) seat rear bolts.
(Fig. 4-2)
(d) Slide the seat backward.
Fig. 2-4
10 m
m
Socket
,
Ratchet
,
Extension
Bolts x4
Fig. 3-1
Stoppers x2
Claws x2
Damper
①
②
②
Fig. 4-1
Phillips Screwdriver, Panel Removal Tool
Bracket Covers
(Right Side)
Screw x1
Bracket Cover
(Left Side)
Claws x2
Rear Side
Fig. 4-2
14 m
m
Socket, Ratchet, Extension
Bolts x2
Rear Side
STOP

SCION xB 2008 - XM SATELLITE RADIO
Procedure
Page 9 of 21 pages DIO
Issue:A 02/28/07
(e) Remove the two (2) seat front bolts.
(Fig. 4-3)
(f) Disconnect the wire harness clamp and
connectors.
(g) Tilt the seat rearwards, exposing the floor
under the front passenger seat, and lay the
seat in the rear seat area.
(h) Secure the seat to keep it from falling
(optional).
5. Route the Satellite Tuner Cable
(a) Route the tuner cable from the cowl side
trim to the head unit as shown. (Fig. 5-1)
(b) Secure the tuner cable with the vehicle wire
harness. Install six (6) lock ties A as shown.
(Fig. 5-2)
NOTE: Match the position of the connector
and the length of the cable to other
connectors connected with the head
unit.
(c) Check that the lock ties are at the correct
positions. (Fig. 5-3)
(d) Use a side cutter to cut off the excess lock
tie length.
Fig. 5-2
Side Cutter Cushion Ta
p
e
End of Cushion
Lock Tie A x3
①
②
③
④
⑤
⑥
①②
Lock Tie Ax3
Fig. 5-3
②
③④
⑤
Lock Tie A
Cushion Ta
p
e
View from lower side
Lock Tie A
Fig. 4-3
14 m
m
Socket, Ratchet, Extension
Front Side
Bolts x2
Fig. 5-1
Connecto
r
Cushion Ta
p
e
STOP

SCION xB 2008 - XM SATELLITE RADIO
Procedure
Page 10 of 21 pages DIO
Issue:A 02/28/07
6. Route the Tuner Ground Cable
(a) Install the end of the tuner ground cable onto
the bolt located on the cowl side. (Fig. 6-1)
(b) Secure the tuner ground cable and tuner cable
using the vehicle wire harness clamps.
(c) Secure the tuner ground cable and tuner cable
to the vehicle wire harness using a lock tie A
as shown. (Fig. 6-1)
(d) Use a side cutter to cut off the excess lock tie
length.
7. Install the Antenna
(a) Clean the template (template B) mounting
area with 3MTM Prep Solvent 70 and cleaning
method. (Fig. 7-1)
(b) When cleaning with 3MTM Prep Solvent 70
and cleaning method,
(1) Always use a clean (lint free scratch
resistant) soft cloth (or wipe), and clean a
small area at a time (~ 3 ft. x 3 ft. max.).
(2) Shake well.
(3) Apply 3MTM Prep Solvent 70 to cloth or
wipe. Do not spray cleaning solution
directly on any vehicle surfaces.
(4) Clean surface thoroughly and wipe dry
immediately with a new clean cloth. Do
not allow cleaner to air dry.
(c) Position antenna template on the near right
corner of the roof as shown. Secure the
template with masking tape. (Fig. 7-1)
(d) Remove the release paper from the back of
antenna, and then affix the antenna onto the
roof. (Fig. 7-2)
(1) Align the front edge of the antenna with
the template as shown and install it
carefully.
(2) Once attached, the antenna cannot be
easily removed.
Fig. 7-1
Roof
Template
Roof
Template Template Ditch
Molding
Masking Tape Front
Fig. 7-2
Antenna
Front
Protective Paper Align with the
front edge
Double-Sided
Adhesive Tape
Fig. 6-1
10 m
m
Socket, Ratchet, Extension, Side Cutte
r
Lock Tie A x1
Ground Point
Front Clamps x3
Tuner Cable
Ground Cable
STOP
STOP
STOP

SCION xB 2008 - XM SATELLITE RADIO
Procedure
Page 11 of 21 pages DIO
Issue:A 02/28/07
8. Route Antenna Cable through Body
Opening
(a) The roof and the roof/hatch area where the
sheet tape and cord rail attach must be
cleaned with 3MTM Prep Solvent 70 using
the method defined in Step 7(b). (Fig. 8-1)
(b) First, pass the grommet part through the
space between the back door and the body.
(c) Locate with sheet tape and a cord rail so the
door does not contact or pinch the antenna
cable. (details in Fig. 8-2)
(d) Route the antenna cable around the body
opening, and insert the cable under the
weather strip.
(e) Remove and discard the vehicle grommet
covering the body opening. (Fig. 8-3)
(1) From the inside, push outward and
remove the grommet plug of the right
rear combination light installation area,
then route the antenna cable through
the body hole.
(f) The body opening where the antenna
grommet attaches must be cleaned with
3MTM Prep Solvent 70 and cleaning
method.
(g) After cleaning, apply 3MTM Ultra-Pro Body
Sealant to the backside of the grommet.
Fig. 8-1
Antenna
Sheet Ta
p
e x1
Cord Rail x1
5 mm
(0.20 in)
Insert under the
weather strip.
Fig. 8-3
Grommet
Body Opening
Fig. 8-2
Antenna
Back Door

SCION xB 2008 - XM SATELLITE RADIO
Procedure
Page 12 of 21 pages DIO
Issue:A 02/28/07
(h) Run the antenna cable and insert the
antenna grommet (attached to cable) into
the body opening. (Fig. 8-4)
(i) Secure the antenna cable around the area
where the rear combination light is installed
as shown using four (4) sheet tape pieces.
(Fig. 8-4)
(1) Make sure the tape does not contact the
rubber with the backside of the rear
combination lamp.
(j) Wrap the cushion tape around the antenna
cable as shown in the illustration. (Fig. 8-5)
9. Secure the Antenna Cable
(a) Secure the antenna cable to the rear right
side inner panel using the three (3) sheet
tapes and three (3) protective sheets as
shown. (Fig. 9-1)
(b) Secure the antenna cable to the vehicle wire
harness using the seven (7) lock ties
(type B). (Fig. 9-2)
NOTE: Do NOT secure the antenna cable
to the washer hose.
(c) Use a side cutter to cut off the excess lock
tie length.
Fig. 8-4
Please disregard
the gray marking
tapes, as they are
used for
alignment in
other models.
Antenna
Grommet
Sheet Tapes x4
Pull out from
weather strip.
Fig. 8-5
50 mm
(1.97 in.)
Grommet
Cushion Tape
(20 x 100 mm)
(
0.79 x 3.94 in.
)
Fig. 9-1
Sheet Ta
p
es x3
Cushion Tape
Protective Sheets x2
Protective Sheet
Front
Fig. 9-2
Side Cutter
Front
Lock Tie B x7
Washer Hose
STOP

SCION xB 2008 - XM SATELLITE RADIO
Procedure
Page 13 of 21 pages DIO
Issue:A 02/28/07
(d) Secure the antenna cable to the vehicle wire
harness using the one (1) lock tie B and
vehicle wire harness clamps. (Fig. 9-3)
NOTE: Do NOT secure the antenna cable
to the washer hose.
(e) Use a side cutter to cut off the excess lock
tie length.
10. Attach a Housing to the Antenna Cable
Terminal
(a) Remove the polyurethane cover from the
terminal. (Fig. 10-1)
(b) If the lock plate of the housing is pushed in,
pull it out. (Fig. 10-2)
NOTE : This step is not required if the lock
plate is already pulled out.
(c) Push the terminal into the housing.
(Fig. 10-3)
Fig. 10-2
OK
NG
Lock Plate
(when pushed in)
Lock Plate
(when pulled out by
around 1 mm)
Insert a slim screwdriver
into the notch and lift u
p
.
Fig. 9-3 Lock Tie B x1
Front
Antenna Cable
Vehicle Wire
Harness Clam
p
s
Side Cutter
Fig. 10-1
Antenna Cable Terminal
Polyurethane Cover
Fig. 10-3
Insert the guides on the terminal
into the slits in the housing.
Antenna Cable
Push in until it clicks.
Housin
g
STOP

SCION xB 2008 - XM SATELLITE RADIO
Procedure
Page 14 of 21 pages DIO
Issue:A 02/28/07
(d) Push the lock plate in (Fig. 10-4).
11. Install the Satellite Tuner
(a) Remove the frame number cover.
(Fig. 11-1)
(b) Peel back the carpet and felt.
(c) At the center pillar area, route the cables
and secure them to the vehicle wire harness
using the lock ties A as shown. (Fig. 11-2)
(d) Use a side cutter to cut off the excess lock
tie length.
(e) Clean the bracket mounting surface with
3MTM Prep Solvent 70 and cleaning
method.
(f) Install four (4) cushion A (butyl) onto the
bottom of the base brackets. (Fig. 11-3)
(g) Clean the bracket mounting surface of the
vehicle floor pan with 3MTM Prep Solvent
70.
Fig. 11-3 Base Brackets
Cushion A x4
Fig. 11-2
Antenna Cable
Ground Cable
Side Cutter
Tuner Cable
Lock Tie Ax4
Fig. 10-4
Push in until it clicks.
Fig. 11-1
Frame Number Cover
①
Pull u
p
ward.
②Move toward front
passenger door.

SCION xB 2008 - XM SATELLITE RADIO
Procedure
Page 15 of 21 pages DIO
Issue:A 02/28/07
(h) Position template A under the passenger's
seat as shown. (Fig. 11-4)
(i) Remove the release paper from the four (4)
cushion tape A (butyl), and then secure the
base brackets over template A as shown.
(j) Remove template A.
(k) Route the tuner cable, tuner ground cable
and antenna cable together and secure the
excess of the cables using lock ties A.
NOTE: Never secure them with the wire
harness for the seat.
(1) Route the cables under the carpet as
shown. Set the length of the cables over
the carpet required; 140 mm (5.51 in.)
of the tuner ground cable, 100 mm (3.94
in.) of the tuner cable and 240 mm (9.45
in.) of the antenna cable, and secure the
cables with one (1) lock tie A (①).
(Fig. 11-5)
(2) Locate the secured cables to the floor as
shown. (Fig. 11-6)
(3) Verify the cables do not block the rear
heater duct.
(4) Secure the excess of the cables to the
vehicle wire harness using three (3)
lock ties A (②). (Fig. 11-6)
(5) Use a side cutter to cut off the excess
lock tie length.
Fig. 11-4
Base Brackets
Wire Harness
for Seat
Template A
Fig. 11-5
①
Lock Tie A
240 mm
(
9.45 in.
)
140 mm
(5.51 in.)
100 mm
(
3.94 in.
)
Wire Harness
for Seat
Fig. 11-6
Side Cutter Rear Heater Duct
305 mm
(12.01 in.)
①
②
②
②
Lock Tie Ax3
Wire Harness
for Seat
STOP
STOP

SCION xB 2008 - XM SATELLITE RADIO
Procedure
Page 16 of 21 pages DIO
Issue:A 02/28/07
Fig. 11-10
(l) Reinstall the carpet and verify the base
bracket bolt positions. Transfer each bolt
location onto the carpet using carpet punch
and mallet to cut four (4) holes in carpet.
(Fig. 11-7)
(m)Pass the base bracket bolts through the
carpet.
(n) Install the satellite tuner brackets and
ground cable onto the tuner. (Fig. 11-8)
(o) Secure the satellite tuner onto the base
brackets so the connectors face toward the
front of the vehicle. (Fig. 11-9)
(p) Plug the tuner cable and antenna cable into
the tuner. (Fig. 11-10)
(1) Connect the antenna cable connector to
the tuner.
(2) Connect the tuner cable (wire, to radio
installation) to the tuner.
Fig. 11-7
Carpet Punch, Mallet
Front
Fig. 11-9
10 mm Socket, Ratchet, Extension
Front
Nuts (x4)
Fig. 11-8
Front
Phillips Screwdrive
r
Bolts x 4
Ground Cable
Front

SCION xB 2008 - XM SATELLITE RADIO
Procedure
Page 17 of 21 pages DIO
Issue:A 02/28/07
12. Reinstall the Radio/Player Head Unit
(a) Connect the satellite tuner cable and the
connectors removed in Step 2(b) into the
rear of the head unit. (Fig. 12-1)
(b) Insert head unit into opening and re-install
the bolts. (Fig. 12-1)
13. In Process Functional Test
(a) Temporarily reconnect battery negative
cable.
(b) Turn ignition key to “ACC” position.
(c) Press the power button on the
receiver/player head unit. Verify the
backlighting illuminates.
(d) Press and release the “SAT” button on the
head unit.
(1) Verify that a satellite channel is
received, or a “NO SIGNAL” message
appears on the display.
NOTE: If “ANTENNA” appears (flashing)
on the display – then the antenna
cable is disconnected from the
satellite tuner.
NOTE: If the head unit will not tune or go
into satellite mode – then the tuner
cable is disconnected from the
satellite tuner.
(e) Disconnect battery negative cable.
Fig. 12-1
Phillips Screwdriver
Bolts x4

SCION xB 2008 - XM SATELLITE RADIO
Procedure
Page 18 of 21 pages DIO
Issue:A 02/28/07
14. Installing Receiver Cover
(a) Remove the satellite receiver cover (P/N
PT218-52071) from the poly bag.
(b) Shape the cover so that it forms an open
box shape with the VelcroTM facing down.
NOTE: Shipping and storage may have caused the
shape to distort.
(c) Peel the backing off the sewn-in VelcroTM
strip inside the cover. (Fig.-14-1).
(1) Do not separate the VelcroTM.
(d) Clean the top of satellite receiver box with
3MTM Prep Solvent 70 using the method
defined in Step 7(b).
(e) Align the rear edge of the cover with the
rear edge of the satellite receiver.
(Fig. 14-2).
(f) Center cover to ensure satellite receiver
mounting bolts are covered. Press VelcroTM
to the floor carpet around the perimeter.
(g) Press the sewn-in VelcroTM tab on the top
underside of the cover firmly to the satellite
receiver. (Fig. 14-3).
15. Complete the Reassembly of Vehicle
(a) Reinstall rear combination light.
(b) Reconnect any disconnected connectors.
(c) Re-install the front seat
(1) Reinstall the four (4) bolts loosely, then
tighten them in the following order:
Rear inner bolt
Rear outer bolt
Front inner bolt
Front outer bolt
(2) Tighten bolts to 37 N•m (27 lbf•ft)
Fig. 14-1
VelcroTM Backing
Fig. 14-2 Rear Edge
Fig. 14-3 Sewn-in VelcroTM Tab

SCION xB 2008 - XM SATELLITE RADIO
Procedure
Page 19 of 21 pages DIO
Issue:A 02/28/07
(d) Re-install the passenger side deck trim side
panel as follows:
(1) Install the deck trim side panel and
engage the clips and claws. (Fig. 15-1)
(e) Install the rear seatback hinge and bolt B.
(Fig. 15-2)
(1) Tighten bolt B to 18 N•m (13 lbf•ft)
(f) Install the two (2) luggage compartment
trim hooks with the bolts A.
(g) Install the service hole cover.
(h) Re-assemble the passenger front seat belt.
(1) Bolt and attach the passenger front seat
belt anchor plate.
(i) Tighten the bolt to 42 N•m (31
lbf•ft)
(2) Attach the passenger front seat belt
anchor cover.
(i) Re-assemble the rear seat.
(1) Install the rear center seat belt
installation bolt and tighten it to 42
N•m (31 lbf•ft).
(2) Install the rear seat cushion, taking care
that the retaining hooks are securely
engaged.
(3) Bolt and attach the right rear seatback.
(4) Tighten bolts to 42 N•m (31 lbf•ft)
(5) Fold up the seatback, and then fold
down the cover over the bolts.
(j) Verify the panels fit together properly with
no uneven gaps between them.
Fig. 15-2
Torque Wrench, 10 mm Socket
12 mm Socket
,
Extension
Bolt B
Bolts A x2
Clip x1
Claws x 5
Trim Hooks
Rear Seatback
Hinge
Service Hole Cover
Fig. 15-1
Claws x5
Clips x3
Clips x 3

SCION xB 2008 - XM SATELLITE RADIO
Procedure
Page 20 of 21 pages DIO
Issue:A 02/28/07
16. Reconnect Battery Cable
(a) Reconnect the vehicle’s negative battery
cable. (Fig. 16-1)
(1) Position the negative terminal to the
battery as shown (original factory
position).
(2) Tighten the nut to 4.1 N•m (36 lbf•in).
(3) Do not touch the positive terminal with
any tool when installing the cable.
(b) Clean up and remove any trash.
(c) Place the owner “XM Satellite Radio”
brochure in the glove box.
Fig. 16-1
Battery
10 mm Soc
k
et, Torque Wrench Negative
Battery
Cable