TP-Link omada OC200 User manual

User Guide
For TP-Link Omada Access Points
1910012995 REV4.7.0
July 2021

I
CONTENTS
About This User Guide........................................................................................................ 1
Overview ................................................................................................................................. 3
1 Quick Start....................................................................................................................... 4
1.1 Determine the Management Method.................................................................................................. 5
1.2 Connect Network Devices...................................................................................................................... 6
1.3 Log in to the EAP and Change the SSID............................................................................................. 8
1.4 Configure and Manage the EAP..........................................................................................................21
2 Configure the Network.............................................................................................. 22
2.1 Configure the Wireless Parameters..................................................................................................23
2.1.1 Configure SSIDs .............................................................................................................................. 24
2.1.2 Configure Wireless Advanced Settings ................................................................................. 30
Radio Setting.................................................................................................................................... 30
Load Balance.................................................................................................................................... 32
Airtime Fairness .............................................................................................................................. 32
More Settings .................................................................................................................................. 33
2.2 Configure Portal Authentication ........................................................................................................35
Configure Portal............................................................................................................................................ 36
Configure Free Authentication Policy .................................................................................................. 42
2.3 Configure VLAN........................................................................................................................................45
2.4 Configure MAC Filtering........................................................................................................................46
2.5 Configure Scheduler...............................................................................................................................49
2.6 Configure Band Steering.......................................................................................................................52
2.7 Configure QoS...........................................................................................................................................54
2.8 Configure Rogue AP Detection...........................................................................................................58
Detect Rogue APs and Move the Rogue APs to the Trusted AP List....................................... 59
Manage the Trusted AP List..................................................................................................................... 60

II
3 Monitor the Network ..................................................................................................62
3.1 Monitor the EAP........................................................................................................................................63
3.2 Monitor the Wireless Parameters......................................................................................................65
Monitor the SSIDs........................................................................................................................................ 66
Monitor the Radio Settings....................................................................................................................... 67
Monitor Radio Traffic .................................................................................................................................. 67
Monitor LAN Traffic ..................................................................................................................................... 68
3.3 Monitor the Clients..................................................................................................................................70
View Client Information.............................................................................................................................. 70
View Block Client Information ................................................................................................................. 72
4 Manage the EAP...........................................................................................................73
4.1 Manage the IP Address of the EAP....................................................................................................74
4.2 Manage System Logs .............................................................................................................................77
View System Logs ....................................................................................................................................... 77
Configure the Way of Receiving Logs.................................................................................................. 78
4.3 Configure Web Server............................................................................................................................80
4.4 Configure Management Access.........................................................................................................81
Configure Access MAC Management.................................................................................................. 81
Configure Management VLAN ................................................................................................................ 82
4.5 Configure LED ...........................................................................................................................................83
4.6 Configure Wi-Fi Control (Only for Certain Devices)....................................................................84
4.7 Configure PoE Out (Only for Certain Devices) ..............................................................................85
4.8 Configure SSH...........................................................................................................................................86
4.9 Configure SNMP.......................................................................................................................................87
5 Configure the System................................................................................................ 89
5.1 Configure the User Account ................................................................................................................90
5.2 Controller Settings..................................................................................................................................91
Enable Cloud-Based Controller Management .................................................................................. 91
Configure Controller Inform URL ........................................................................................................... 93

III
5.3 Configure the System Time..................................................................................................................94
Configure the System Time ..................................................................................................................... 95
Configure Daylight Saving Time............................................................................................................. 97
5.4 Reboot and Reset the EAP....................................................................................................................99
5.5 Backup and Restore the Configuration......................................................................................... 100
5.6 Update the Firmware ........................................................................................................................... 101
6 Application Example ............................................................................................... 102
6.1 Determine the Network Requirements ......................................................................................... 103
6.2 Build the Network Topology.............................................................................................................. 104
6.3 Log in to the EAP ................................................................................................................................... 105
6.4 Configure the EAP ................................................................................................................................ 106
Configure SSIDs .........................................................................................................................................106
Configure Portal Authentication...........................................................................................................107
Configure Scheduler.................................................................................................................................109
6.5 Test the Network................................................................................................................................... 111

1
About This User Guide
When using this guide, notice that features available in the EAP may vary by model and software
version. Availability of the EAP may also vary by region or ISP. All images, steps, and descriptions in
this guide are only examples and may not reflect your actual experience.
Some models featured in this guide may be unavailable in your country or region. For local sales
information, visit https://www.tp-link.com .
The information in this document is subject to change without notice. Every effort has been made
in the preparation of this document to ensure the accuracy of the contents, but all statements,
information, and recommendations in this document do not constitute the warranty of any kind,
express or implied. Users must take full responsibility for their application of any product.
Conventions
Unless otherwise noted, the introduction in this guide takes EAP245 as an example.
Wireless Speed, Range and Connected Devices Disclaimer
Maximum wireless transmission rates are the physical rates derived from IEEE Standard 802.11
specifications. Range and coverage specifications along with the number of connected devices
were defined according to test results under normal usage conditions. Actual wireless transmission
rate, wireless coverage, and number of connected devices are not guaranteed, and will vary as a
result of 1) environmental factors, including building materials, physical objects and obstacles, 2)
network conditions, including local interference, volume and density of traffic, product location,
network complexity, and network overhead and 3) client limitations, including rated performance,
location, connection quality, and client condition.
MU-MIMO Disclaimer (for EAPs that support MU-MIMO)
MU-MIMO capability requires client devices that also support MU-MIMO.
Seamless Roaming Disclaimer (for EAPs that support Seamless Roaming)
Seamless roaming requires both the access point and client devices to support 802.11k and
802.11v protocols.
Lightning and Electro-Static Discharge Protection Disclaimer (for Outdoor EAPs)
Protection against lightning and electro-static discharge may be achieved through proper product
setup, grounding and cable shielding. Refer to the instruction manual and consult an IT professional
to assist with setting up this product.

2
More Info
Some models featured in this guide may be unavailable in your country or region. For local sales
information, visit https://www.tp-link.com .
For technical support, latest software, and management app, visit https://www.tp-link.com/support .
The Quick Installation Guide can be found where you find this guide or inside the package of the
EAP.
The authentication information can be found where you find this guide.
Specifications can be found on the product page at https://www.tp-link.com .
To ask questions, find answers, and communicate with TP-Link users or engineers, please visit
https://community.tp-link.com to join TP-Link Community.
If you have any suggestions or needs on the product guides, welcome to email
[email protected] .

3
Overview
Omada series products provide wireless coverage solutions for small-medium business and
households. They can either work independently as standalone APs or be centrally managed by
Omada Software Controller, Omada Hardware Controller (OC200/OC300), or Omada Cloud-Based
Controller, providing a flexible, richly-functional but easily configured wireless network for small-
medium business and households.

4
1
Quick Start
This chapter introduces how to build a wireless network using the EAPs and how to
complete the basic settings. Follow the steps below:
1.1 Determine the Management Method
1.2 Connect Network Devices
1.3 Log in to the EAP and Change the SSID
1.4 Configure and Manage the EAP

5
1.1 Determine the Management Method
Before building your network, choose a proper method to manage your EAPs. You have
the following two options:
■ Controller Mode
If you want to manage a large-scale network centrally, choose Controller Mode. In
Controller Mode, you can configure and monitor mass EAPs, switches, and gateways via
Omada SDN Controller. For detailed instructions, go to the Support Webpage of Omada
Controller and download the User Guide.
■ Standalone Mode
If you want to manage only a few EAPs, choose Standalone Mode. In Standalone Mode,
you can singly configure and monitor your EAPs via Omada APP or a web browser, and
each EAP has its own management page.
This chapter introduces how to start configuring the EAP in Standalone Mode.
Note:
•Standalone Mode is inaccessible while the EAP is managed by a controller. To turn the EAP back
to Standalone Mode, you can forget the EAP on the controller or reset the EAP.
•To make your EAPs discovered by the controller, you need to configure
5.2 Controller Settings
in certain scenarios.

6
1.2 Connect Network Devices
To connect your EAPs to the local network, refer to the following topology.
In
ternet
Clients
Router (DHCP Server)
WANLAN
EAP
EAP
1. Connect the WAN port (or Internet port) of the router to the internet.
2. Connect your EAPs to the LAN port of the router.
3. Connect your wireless clients such as phones, tablets and laptops to the WiFi of the
EAP. The default SSID is printed at the bottom of the EAP.
Now you can surf the internet on your phones, tablets and laptops. If you cannot access
the internet, follow the FAQ to troubleshoot the problem.

7
Tips:
•If you want to power your EAPs using a PoE switch, refer to the following topology.
In
ternet
Clients
Router (DHCP Server)
WANLAN EAP
EAP
PoE Switch
•The router is the gateway of the network, and devices in the LAN surf the internet via the router.
At the same time, the router acts as a DHCP server to assign dynamic IP addresses to the EAPs
and clients.
•The dual-band EAP has two default SSIDs named TP-Link_2.4GHz_XXXXXX on the 2.4GHz band
and TP-Link_5GHz_XXXXXX on the 5GHz band, and the single-band EAP has a default SSID
named TP-Link_2.4GHz_XXXXXX on the 2.4GHz band.

8
1.3 Log in to the EAP and Change the SSID
By default, anyone can connect to the WiFi of EAP without authentication, because the
default SSID has no password. For security purposes, we recommend changing the default
SSID.
Log in to the EAP before changing the default SSID. You can use either Omada App on
your mobile device or the web browser on your PC. Choose a method from the following
sections and follow the instructions.
Tips:
•Only one user is allowed to log in to the EAP at one time.
•Omada app is designed to help you quickly configure some basic settings. To configure advanced
functions, use the web browser on your PC.
•Omada app is only compatible with certain firmware versions of the EAP. To check the firmware
versions of the supported EAPs, please refer to https://www.tp-link.com/omada_compatibility_
list.
■Using Omada App on Your Mobile Device
In
ternet
Router (DHCP Server)
WANLAN
EAP
EAP
Mobile Device Installed
with Omada App
1. To install Omada App, launch the Apple App Store (iOS) or Google Play store (Android)
and search “TP-Link Omada” or simply scan the QR code to download and install the
app.
Scan for Omada App Download Omada App
or

9
2. Connect your mobile device to the WiFi of the EAP. The default SSID is printed at the
bottom of the EAP.
3. Launch the Omada app, tap Standalone APs and wait for the EAP to be discovered.
Tips:
All the EAPs in the same subnet will be discovered by Omada app and shown on the page.

10
4. Tap on the EAP appearing on the page. Set a new username and password for your
login account of the EAP.
5. Change the SSID and password to keep your wireless network secure. Tap Next.

11
6. Confirm the settings in the summary page. Tap Next, and the settings will take effect in
several minutes.
7. To join your new wireless network, select the SSID and tap Join.

12
8. Tap Continue to go to the managment page. In this page, you can view the information
and settings of the EAP. If you want to change the settings incuding radio, SSID and
device account, tap .
Now you can connect your phones, tablets and laptops to the new WiFi. If you cannot
access the internet, follow the FAQ to troubleshoot the problem.
■Using Web Browser on Your PC and Connecting to the WiFi
In
ternet
Router (DHCP Server)
WANLAN
EAP
EAP
PC

13
1. Set your PC to obtain an IP address automatically.
2. Connect your PC to the WiFi of the EAP. The default SSID is printed at the bottom of the
EAP.

14
3. Make sure that your PC has got the IP address, default gateway, and DNS server from
the DHCP server.
4. To log in to the EAP, launch a web browser and enter http://tplinkeap.net in the address
bar. The login page will appear. By default, both the username and password are admin.

15
5. After logging in to the EAP, follow the step-by-step instructions to complete the basic
configurations. In the pop-up window, configure a new username and a new password
for your user account, then click Next.
6. Configure the SSID and password. For the dual-band EAP, you can configure the SSID
and password for both 2.4GHz and 5GHz. Click Save.
Tips:
You can skip this step and configure wireless settings later on the management page. If needed,
you can also create more SSIDs. For detailed instructions, refer to
2.1 Configure the Wireless
Parameters
.

16
7. The following page will appear. Make sure that your device has connected to the new
wireless network and tick the checkbox. Then click Finish.
Now you can connect your phones, tablets and laptops to the new WiFi. If you cannot
access the internet, follow the FAQ to troubleshoot the problem.
■Using Web Browser on Your PC and Connecting to the Ethernet
1. Get the IP address of the EAP. There are two methods.
• Using DHCP Client List of the Router
Log in to the router which acts as the DHCP server. In the DHCP client list, find the IP
address of your EAP according to its MAC address. The MAC address can be found at