Transition Networks LANMaster T8 User manual

Lan Master™ T8
8 port Ethernet Hub with SIC Slot
ASSEMBLY INSTRUCTIONS
Satisfi Design

Introduction
The Lan Master™ T8 is an eight-port Ethernet Hub which allows computers to
communicate with each other. Up to eight (8) computers can be plugged in to the Ethernet
Hub at one time.
Putting together your Transition Networks®Lan Master™ is easy. Simply follow the
instructions and illustrations, and in minutes your Ethernet Hub will be ready for use! (See
Instruction Manual for how to use your Lan Master™ T8 once it is assembled.)
Table of Contents
.............................................................................................0.1 Parts List 2
....................................................0.2 Side Labels for Platform and Cover 3
..................................................1.0 Installing the Circuit Network Board 4
..............................2.0 Installing the Power Supply Printed Circuit Board 7
............................................................3.0 Connecting the Circuit Boards 9
...................................................4.0 Installing the Input Power Conduit 12
...........................................................................5.0 Securing the Cover 17
Transition Networks®Lan Master TM T8 Assembly Instructions
Version 1.1
Page 1
6475 City West Parkway
Minneapolis, MN 55344
www.transition.com
Satisfi Design

0.1 Parts List
Transition Networks®Lan Master TM T8 Assembly Instructions
Version 1.1
Page 2
Nuts (3)
Washers (11)
Size 1 Screws (5)
Size 2 Screws (14)
Size 3 Screws (2)
Cover
Saddle
Grounding Cable
Input Power Conduit
Power Supply Printed
Circuit Board
Circuit Network Board
Platform
You will also need:
Phillips Screwdriver
(Not Included)
Satisfi Design

0.2 Side Labels for Platform and Cover
Transition Networks®Lan Master TM T8 Assembly Instructions
Version 1.1
Page 3
Side A
Side B Side C
Side D
Side A
Side B Side C
Side D
Figure 0.2
Satisfi Design

1.0 Installing the Circuit Network Board
+
+
1.1 To position the Circuit Network Board
1.1.1 Locate the five (5) screw holsters near side A and side D of the platform.
1.1.2. Slide the Circuit Network Board under the opening of Side A and set down on top of screw
holsters.
Transition Networks®Lan Master TM T8 Assembly Instructions
Version 1.1
Page 4
Screw
Holsters
Side D Side A
Figure 1.0
Figure 1.1.1
Figure 1.1.2
Satisfi Design

1.2 To secure the Circuit Network Board
1.2.1 Align the screw holes of the Circuit Network Board with the screw holsters of the platform.
1.2.2. Place one (1) washer on top of each screw hole and insert Size 1 Screws.
1.2.3. Tighten the screws by turning the Phillips screwdriver clockwise.
Transition Networks®Lan Master TM T8 Assembly Instructions
Version 1.1
Page 5
Figure 1.2.2
Figure 1.2.3
Tighten until the screw does not turn
easily anymore. Over-tightening will
damage the circuit board.
Screw
Holes
Figure 1.2.1
Satisfi Design

Transition Networks®Lan Master TM T8 Assembly Instructions
Version 1.1
Page 6
The Installed Circuit Network Board
Figure 1.3
Satisfi Design

2.0 Installing the Power Supply Printed Circuit Board
+
2.1 To position the Power Supply Printed Circuit Board
2.1.1 Locate the four (4) remaining screw holsters near side A and side B of the platform.
2.1.2 Set the Power Supply Printed Circuit Board on the screw holsters as shown.
2.2 To secure the Power Supply Printed Circuit Board
2.2.1. Align the screw holes of the Power Supply Printed Circuit Board with the screw holsters of
the platform.
Transition Networks®Lan Master TM T8 Assembly Instructions
Version 1.1
Page 7
Figure 2.0
Side A
Side B
Figure 2.1.2
✗
✓
Figure 2.2.1
Satisfi Design

2.2.2. Place one (1) washer on top of each screw hole and insert Size 2 Screws.
2.2.3. Tighten the screws by turning the Phillips screwdriver clockwise.
Transition Networks®Lan Master TM T8 Assembly Instructions
Version 1.1
Page 8
The Installed Power Supply Printed Circuit Board
Tighten until the screw does not turn
easily anymore. Over-tightening will
damage the circuit board.
Figure 2.2.2
Figure 2.2.3
Satisfi Design

3.0 Connecting the Circuit Boards
3.1 To link the circuit boards via the saddle
3.1.1. Plug the saddle into the Power Supply Printed Circuit Board as shown.
3.1.2. Snap the saddle into Circuit Network Board as shown.
Transition Networks®Lan Master TM T8 Assembly Instructions
Version 1.1
Page 9
Snap!
+
+
✗
✗
✓
✓
Snap!
Figure 3
Figure 3.1.1
Figure 3.1.2
Satisfi Design