Travis Industries SKU 94400111 User manual

Accent Light, Type 2A
(SKU 94400111)
Page 1 of 5 3/28/07 © Travis Industries, Inc.
Compatibility
• DVS Insert (2005)
• DVL Insert (2005)
• 2007 Tree of Life (Rev 001) w Blower (99000153)
• 2007 Berkshire (99600113, 4) w Blower (99000153)
Packing List
• Accent Light Assembly (with strain relief plate)
• Rheostat Assembly (includes Wiring Harness)
• (2) #8 Nuts
• Wire Nut
• 35 Watt 120 Volt T4 Halogen Bulb (G6.35 Base)
Make sure power to the heater has been turned off prior to installation (unplug the power cord).
Do not connect 110-120 VAC to the gas control valve or the on/off circuit on this fireplace.
IMPORTANT INSTALLATION NOTE FOR MODELS USING THE FIREBACKS:
Follow the steps below i installing the irebacks with an accent light.
• Remove the burner (see the manual or details).
• Install the rear ireback (see the instructions included with the irebacks).
• Install the accent light.
• Replace the burner.
• Install the side irebacks (see the directions included with the irebacks).
DVS / DVL Installation
NOTE: The bulb is shipped separately. Do not touch the bulb – oil or other residue left on the bulb may lead to
premature bulb failure. Use a cloth or paper towel to handle the bulb.
1 Remove the burner (see the manual for details).
2 Install the accent light as shown below.
NOTE: the illustrations below show a DVL Insert - the accent light installs in the same manner on a DVS Insert.
AA
AA
AA
AA
AA
Remove this screw, position the accent
light assembly in the same location, and
attach with the same screw.
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
a
b
NOTE: The cover plate is
here on the DVS.
NOTE: To prevent heat-damage to the
wires, make sure this clip holds the
wires down, away from the burner.
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
NOTE: This insulation protects
the wiring - it may be compressed
if necessary.
Remove and discard the
cover plate (keep the
gasket and screws).
Route the wires from the accent light through gasket and hole. Attach the accent light cover plate
(with grommet) to the firebox floor with the screws removed in step “b”. Pull the excess wire through
the grommet, towards the front of the stove (this helps prevent the wire from contacting the burner).
NOTE: On the DVS, make
sure to use the lower screw.
c

Accent Light, Type 2A
(SKU 94400111)
Page 2 of 5 3/28/07 © Travis Industries, Inc.
3 Attach the rheostat assembly and wiring harness as shown below.
AA
AA
AA
A
Disconnect the molex connector
leading to the power cord.
Attach the two molex connectors on the
rheostat wiring harness to the power cord and
the molex connector on the appliance.
Attach the quick-
connect from the
accent light to the
quick-connect on the
rheostat wiring
harness.
Use the included wire nut to connect
the wire leading from the rheostat to
the remaining wire leading from the
accent light.
Slide the rheostat assembly into
place and secure with the
included nuts.
d
e
Make sure all wiring does not contact the
firebox or blower (use wireties if necessary).
a
b
NOTE: Make sure the
grounding wire remains
attached (if applicable).
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
c
4 Install the bulb into the accent light (take care to not touch the bulb).
5 Restore the firebox to the correct configuration (replace the burners, etc.).

Accent Light, Type 2A
(SKU 94400111)
Page 3 of 5 3/28/07 © Travis Industries, Inc.
Tree of Life / Berkshire Installation
NOTE: The bulb is shipped separately. Do not touch the bulb –oil or other residue left on the bulb may lead to
premature bulb failure. Use a cloth or paper towel to handle the bulb.
1 Modify the accent light assembly as shown in the illustration below.
Loosen these nuts
and slide the light
receptacle out (take
care to not touch the
halogen bulb)
Re-attach the
receptacle to the
opposite side.
Remove the screw
that holds the accent
light bracket in place.
Re-attach it in the
second hole from the
top. This lowers the
accent light for proper
light placement.
Accent Light Bracket
Bend this tab upwards
to a 90°angle.
ab
c
2 Remove the burner from the stove (see owner’s manual for details). Install the accent light assembly as
shown in the illustration below.
AA
AA
AA
A
A
A
Remove this screw on the firebox floor.
Position the accent light assembly in the
same location, and re-attach the screw to
secure the accent light assembly.
NOTE: This insulation protects the wiring - it
may be compressed if necessary.
Remove and discard the cover
plate (accessed from below).
a
b
NOTE: The accent light requires the right side access hole. If
this hole is being used for the thermodisk for optional blower,
switch the thermodisk to the mounting position on the left side.
NOTE: To prevent heat-damage to the wires,
make sure this wires are routed along the
floor of the firebox, away from the burner.
Route the wires from the
accent light through gasket
and hole. Attach the accent
light cover plate (with
grommet) to the firebox floor
with the screws removed in
step “b”. Pull the excess
wire through the grommet,
towards the front of the stove
(this helps prevent the wire
from contacting the burner).
c
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA

Accent Light, Type 2A
(SKU 94400111)
Page 4 of 5 3/28/07 © Travis Industries, Inc.
3 Attach the rheostat assembly following the directions below.
AA
AA
AA
A
A
A
Disconnect the molex connector
leading to the power cord.
Attach the two molex connectors on the
rheostat wiring harness to the power cord and
the molex connector on the appliance.
Attach the quick-
connect from the
accent light to the
quick-connect on the
rheostat wiring
harness.
Use the included wire nut to connect
the wire leading from the rheostat to
the remaining wire leading from the
accent light.
Slide the rheostat assembly into
place and secure with the
included nuts.
d
e
Make sure all wiring does not contact the
firebox or blower (use wireties if necessary).
a
b
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
c
4 Install the bulb into the accent light (take care to not touch the bulb).
5 Restore the firebox to the correct configuration (replace the burners, etc.).

Accent Light, Type 2A
(SKU 94400111)
Page 5 of 5 3/28/07 © Travis Industries, Inc.
Accent Light Operation
OFF
Turn the dial all the
way counter-clockwise
until it clicks off.
HIGH
The high position
is all the way
clockwise.
LOW
Turn the dial 180°
clockwise until the light
begins to glow.
NOTE: The accent light responds best when turned to high, then turned down to the desired light level.
Bulb Replacement
NOTE: Do not touch the bulb –oil or other residue left on the bulb may lead to premature bulb failure. Use
a cloth or paper towel to handle the bulb.
The accent light must be replaced with 35 Watt 120 Volt T4 Halogen Bulbs (G6.35 Base) –available at most
hardware stores. To replace the bulb, simply remove it from the socket and insert the new bulb (pin
orientation does not matter).