Travis Industries 95900388 User manual

3615/4415/6015 Trim Kit Installation
See SKU’s Below
Page 1 of 4 17601847 - 5/7/14 Travis Industries, Inc.
Compatibility / Sizing / SKU’s
4415 – First 315 Units ARE NOT COMPATIBLE
4415 fireplaces, serial number 3212-000001 through 3212-000315 are not compatible with the trim kit (the
firebox opening was not wide enough).
4415 – Early Units REQUIRE NEW CONCEALMENT COVER
4415 fireplaces, serial number 3212-000316 through 3212-000883 used a concealment cover that is too wide
for the 4415 trim kit. If you have one of these units, contact Travis Industries to receive a revised concealment
cover (part # 250-03302).
In addition, you will need to widen the two ledges the concealment cover rests on inside the fireplace. Use a
screwdriver to widen the ledge as shown below.
Before
After
Minimum Facing Depth Maximum Facing Depth SKU
3615 Standard Facing Kit 1/2” 7/8” 95900388
3615 Thick Facing Kit 1” 1-1/2” 95900390
4415 Standard Facing Kit 1/2” 7/8” 95900392
4415 Thick Facing Kit 1” 1-1/2” 95900394
6015 Standard Facing Kit 1/2” 7/8” 95900396
6015 Thick Facing Kit 1” 1-1/2” 95900398
Packing List
(2) Side Pieces
(2) Top/Bottom Trim Pieces
L Bracket Hardware (4 L Brackets with 2 Set Screws Pre-Installed, 4 L Spacers)
(4) 8-32 x 3/8” Screws
(2) Top Trim Clamps

3615/4415/6015 Trim Kit Installation
See SKU’s Below
Page 2 of 4 17601847 - 5/7/14 Travis Industries, Inc.
Installation
WARNING Turn off gas to the appliance and make sure it has fully cooled prior to conducting service.
HINT: Blacken the Edges of the Extruded Trim
Before constructing the trim assembly, use a black permanent marker to blacken the outer
silver edges of the extruded trim.
1 The trim is attached after the fireplace is in place with the non-combustible facing installed.
2 Assemble the trim kit as shown below. Use one L bracket and spacer for each corner. Use a screwdriver
to tighten the set screws from behind. If the corners are not aligned, loosen the screws, align, and re-
tighten.
Set Screw
Right Side
Trim
Top Trim
"L" Spacer
Standard
Screwdriver
"L" Bracket
3 Remove the screen and glass frame from the fireplace (see the installation manual for details).

3615/4415/6015 Trim Kit Installation
See SKU’s Below
Page 3 of 4 17601847 - 5/7/14 Travis Industries, Inc.
4 Place the trim in place, taking care to not scratch the surfaces. Once it is fully in place, use the included
screws to secure the trim to the fireplace.
Make sure to install the trim right side up. Note how
the side holes are positioned (the smaller gap is to the
top).
When tightening the screws, push the trim against the facing to ensure a seamless fit.

3615/4415/6015 Trim Kit Installation
See SKU’s Below
Page 4 of 4 17601847 - 5/7/14 Travis Industries, Inc.
5 Install the two top clips as shown below. When installing, make sure to place the clips off-center, away
from any rivets or supports. The clips slide under the trim, and as they are moved forward, secure the
trim against the fireplace opening (see the illustrations below).
SIDE VIEW (CUTAWAY)
6 Restore the fireplace to the correct configuration.
Side Trim
Trim Clip
Fireplace
Fron
t