Travis Industries GreenStart Igniter 3 User manual

GreenStart Igniter 3 for Freestanding Stoves
Installation Instructions (SKU 94400955)
Page 1 of 14 17602077.docx— 12/10/19 © Travis Industries, Inc.
Compatibility
Answer (2020 Compliant) or older Answer (Serial Number 1102-074894 or greater)
Endeavor (2020 Compliant) or older Endeavor (Serial Number 1103-55526 or greater)
Liberty (2020 Compliant) or older Liberty (Serial Number 1105-38119 or greater)
Cape Cod Stove
Evergreen Stove
Rockport Stove
Table of Contents
Compatibility ...............................................................................................................................................1 
Table of Contents........................................................................................................................................1 
Electrical Requirements.............................................................................................................................1 
Packing List.................................................................................................................................................2 
Installation Tips...........................................................................................................................................3 
All Stove Models – Igniter Hose Clamp ....................................................................................................3 
Using a Room Blower Outlet with the GreenStart 2 Igniter (US/Canada Only) ....................................4 
Installation ...................................................................................................................................................5 
Igniter Operation.......................................................................................................................................12 
Warnings ................................................................................................................................................12 
Operating Tips........................................................................................................................................12 
Igniter Instructions..................................................................................................................................13 
Electrical Requirements
USA or CANADA: This kit requires 8 amps, 120 Volt AC.
REMOVE AND DISCARD THE SHIPPING BRACKET
Remove and discard this shipping bracket and 2 screws (use a ¼” nutdriver).

GreenStart Igniter 3 for Freestanding Stoves
Installation Instructions (SKU 94400955)
Page 2 of 14 17602077.docx— 12/10/19 © Travis Industries, Inc.
Packing List
Igniter Firebrick

Igniter (the igniter and cover box together are referred to as
“igniter assembly”)
Compressor Assembly

(2) Cover Plates
Cape Cod (10/19 or Later) Universal
2 Cover Boxes
Cape Cod (9/19 or earlier) Universal

2 Wire Loom Sections
(2) Cable Holders
Gasket
Lock-tie
Cord Restraint
Igniter Spacer
(7) 10-24 x ½” screws
(2) Magnets (Used for Cape Cod/Rockport/Evergreen without blower
only)

GreenStart Igniter 3 for Freestanding Stoves
Installation Instructions (SKU 94400955)
Page 3 of 14 17602077.docx— 12/10/19 © Travis Industries, Inc.
Installation Tips
Remove the shipping bracket from the pump box before proceeding with installation.
The igniter assembly must be installed before placing the stove.
If using a blower, install it first.
It is not necessary to install the blower first on the Endeavor, if applicable.
Wood placement is the key. Experiment with different sizes of wood and wood placement until you find a method that
works best for your wood quality and kindling.
The compressor assembly must be placed as shown in the instructions. Placing it on its side, near hot components, or
in a location where temperatures go below 40F will void the warranty and may lead to premature failure.
All Stove Models – Igniter Hose Clamp
A hose clamp is attached to each igniter hose. You will need to set the clamp while attaching the hose to
the igniter. See the photos below.

GreenStart Igniter 3 for Freestanding Stoves
Installation Instructions (SKU 94400955)
Page 4 of 14 17602077.docx— 12/10/19 © Travis Industries, Inc.
Using a Room Blower Outlet with the GreenStart 2 Igniter (US/Canada Only)
An extra outlet for the room blower is included with the GreenStart Igniter 3 for Freestanding Stoves. To
access this outlet remove the top of the pump box using a 5/16” nutdriver.
The outlet ships inside the housing. Route it through the slot and use the included strain-relief to hold the
cable in place (see pictures below). Replace the cover.

GreenStart Igniter 2 for Freestanding Stoves
Installation Instructions (SKU 94400951)
Page 5 of 14 17602077.docx — 12/10/19 © Travis Industries, Inc.
Installation
Modify the firebrick inside the firebox as shown below.
Cape Cod
Evergreen, Rockport, Endeavor, Liberty, Answer
4"x9"
Remove this cover
plate (5/32” Hex
Wrench) and replace
the firebrick.
Remove this brick and
replace it with the igniter
firebrick. The Evergreen
uses the brick included
with the igniter, the
Rockport uses the brick
included with the stove.

GreenStart Igniter 2 for Freestanding Stoves
Installation Instructions (SKU 94400951)
Page 6 of 14 17602077.docx — 12/10/19 © Travis Industries, Inc.
Cape Cod (9/19 or Earlier)
Remove the cover plate and bracket
Endeavor, Liberty, Evergreen & Rockport, Answer
and Cape Cod (10/19 or Later)
Remove the igniter knock-out on the rear of the stove.
This is best done by snipping one of the tabs holding
the knock-out in place then bending the knock-out
repeatedly until it comes loose.

GreenStart Igniter 2 for Freestanding Stoves
Installation Instructions (SKU 94400951)
Page 7 of 14 17602077.docx — 12/10/19 © Travis Industries, Inc.
The knock-out may be discarded.
Remove the igniter cover plate and gasket. Retain the gasket and screws.
Install the igniter spacer using the screws and gasket removed in step 6. Make sure to use the screws that
were removed with the gasket.
Attach the igniter with gasket to the igniter sleeve using the screws and gasket included in this kit. Note that the
igniter gasket is placed between the sleeve and igniter assembly.

GreenStart Igniter 2 for Freestanding Stoves
Installation Instructions (SKU 94400951)
Page 8 of 14 17602077.docx — 12/10/19 © Travis Industries, Inc.
NOTE: The brass nipple faces down.
Place the compressor assembly on the floor next to the stove.
Attach the igniter wires to the compressor assembly wires.
Attach the ¼” tube to the nipple on the igniter.

GreenStart Igniter 2 for Freestanding Stoves
Installation Instructions (SKU 94400951)
Page 9 of 14 17602077.docx — 12/10/19 © Travis Industries, Inc.
Attach the cover plate and igniter cover box over the igniter (cover plates are included with the stove).
Pre-2020 Endeavors – For these stoves the cover plate and cover box are not required. If you do wish to the
conceal the igniter, use self-drilling screws (not included) to secure the cover box to the back of the stove.
Cape Cod 9/19 or Earlier
uses cover plate included with stove.
Everything Else
Use included cover plate see page 2 for details
NOTE: This tab is bent flat on the Answer and
Cape Cod (10/19 or Later)
Place the compressor assembly on the floor behind the stove.
NOTE: An extra outlet may be used with the Cape Cod stove; see page 3.

GreenStart Igniter 2 for Freestanding Stoves
Installation Instructions (SKU 94400951)
Page 10 of 14 17602077.docx — 12/10/19 © Travis Industries, Inc.
Route the igniter switch from the compressor assembly underneath the stove.
Stoves with Blower (except Answer)
Attach the igniter switch bracket to the bottom of the rheostat bracket with two screws.
Stoves without Blower (except Answer)
Attach the igniter switch to the bottom of the stove using the two included magnets.
Answer Only
Attach the igniter switch to the bottom of the stove using the two included screws.