ZKTeco ZM100 User manual

Installation Guide
Version: 1.0
Date: September, 2017
ZM100 Face and Fingerprint Lock

I
Contents
Before Installation.................................................. 1
Diagram.......................................................1
Packing List ...................................................2
Notes................................................................4
Cautions.......................................................4
Installation Environment .....................................5
Check door open direction ...................................6
Tips............................................................7
Installation..........................................................9
Quick operation guide.............................................17

Before Installation
1
Diagram
K
B
D
E
J
H
I
C
G
F
A
C
L
M
N
O
P
R

Packing List
GH
M
BCI
E

2
R
A
Q
F
Wooden Door Security Door

5
Check door thickness, prepare the proper screws and spindles.
3
Door Thickness
35-45mm
45-50mm
50-60mm
60-65mm
D Spindle
(8*8)
65mm
85mm
L Spindle
(5*5)
50mm
60mm
J Screw
(M4)
25mm
40mm
J Screw
(M5)
25mm
40mm
Notes: Screws and spindles for doors thickness of 35-65mm are all included in the standard
package. Please apply the corresponding package according to the actual door thickness.
For the door thickness of 65-90mm, the standard package does not have the proper screws
and spindles. If you need them, please contact with the dealer.

Notes
4
Cautions
1. New lock can not unlock with ANY verification. Please register one administrator at
least first, if there is no any administrator, registration for normal users is not allowed.
2. The lock is equipped with mechanical keys for manual unlocking. Remove mechanical
keys from the package and keep them in a safe place.
3. The lock is equipped with lithium battery.
4. It's forbidden to remove the battery, if you need to replace with newly-bought
battery, please operate under the guidance of professional technique person.
5. Please replace the battery once the lock prompts "Low Battery". Please use the original
charger to charge.
6. Without any operation, the lock will power off automatically within 10 seconds.
7. Keep your fingers, screen and camera clean when using this lock.

3m
1.0m
3m
1.0m
5
Installation Environment
This lock is recommended to be installed in the indoor and semi-outdoor environment,
where the luminance is within 5000Lux.
Recommended installation position:
There are several situation will affect the recognition:
Expose to direct
sunlight (outdoor)
Expose to direct
sunlight through
the window (indoor)
Expose to slant
sunlight through
the window (indoor)
Expose to strong
light at a close
distance (indoor)

GE
Left Inward Right Inward
Left Outward Right Outward
EG
E
GEG
Check door open direction.
Note : Please install the mortise and strike plate according to the above pictures.
Check door type.
Mortise without hooks is applied to wooden door,
and mortise with hooks is applied to security door.
(Without hooks) (With hooks)
6

180°
7
Tips
1. How to change the direction of latch bolt?
Step1: Push the switch to the end
Step2: Push the latch bolt into the mortise
Step3: Rotate the latch bolt at 180° inside mortise,
then loose it.
2. How to change the handle direction?
Front Lock Back Lock

7
Œ
Ž
Loose
screw
K
D

4.How to use mechanical key ?
3. How to use emergency power?
9V Alkaline
Battery
(6LR61)
8
1.Key A is used for lock installer
and upfitter. After the
installation completed, the
owner check and take back Key
A, insert Key B into the keyhole
and rotate 90°, then Key A will
be unable to open the lock.
2.Key B is packed in the sealed
plastic wrap for safety, which is
used only for house owner.
Unlocking method: Please remove
the silicon stopper of the keyhole
first, then insert the key into the
keyhole and rotate 90° to left or
right, press the handle to unlock.
Notes: Key A and Key B are designed
for the property safety of the
house owner:
Caution: Please do not press down the
handle before rotating the key.

安装 步骤
Installation
1. Drill holes on the door
desired handle
height
9
door thickness
35~65mm
center line of the
handle
backset 60mm
Note1:Align the template along the vertical center
line of the mortise(E)at the desired handle
height, and tape it to door.
Note2:Mark the holes first, then start drilling.
1.0m
0.5m
If the user height is 1.35-1.80m, the
height from handle centerline to
ground is 1m.
Recommended installation height

F
2. Install the mortise(E)
E
F
E
10
Note: The mortise with hooks is optional.

3. Install outdoor unit(B) with gasket(C),and spindle(D)
Note: 1. The small triangle must be placed toward the letter of R or L.
2. If the door is right open, the small triangle should towards R.
3. If the door is left open, the small triangle should towards L.
11
Step1 Step3
Step2
Right Open
Left Open
B
C
D
D
B
D

How to change the location of stud bolts?
Note: There are four square holes to be used.
Step2:Twist down the other stud bolt.
M3
M5
12
Step1: Twist down the eight M3 screws and M5
stud bolt to take down the mounting plate.
Note: Before install the waterproof gasket, if the height of stud
bolts is unsuitable for the existed holes, you can adjust
stud bolts location to make the lock suitable.

13
4. Install mounting plate (I) with gasket(C), spring(K) and spindle(L)
13
Step1 Step2 Step3
I
C
C
I
J
DK
L
L
K
L
Tighten screws to fix the spindle.
M1.Make sure spring K can
withstand the front handle
spindle before installation.
2.Insert 5*5 spindle L, and
then tighten the small
screws according to the
pictures.

5. Install indoor unit (M) 6. Install battery (N)
14
R
M
O
N
M
M
R
Note: The battery is installed at default and
equipped with 1 piece lithium battery.
When you purchase a rechargeable
battery, please install according to the
following pictures. Remove the battery
for charging is not recommended.
Install batteries and connect the battery joint.

15
M
P
O
Lift the silicon cover in the below red box to recharge.
Silicon Cover

16
7. Mark and drill holes for strike
261mm
177mm
80.5mm
31mm
33mm
22.2mm
12mm
34.6mm
42mm
24mm
18mm
2mm
1.2mm
G
HF
F
16

Touch the power-on button to
power on the lock
17
Quick operation guide
Open the door with face
Open the door with fingerprint
Verify the face
Verify the fingerprint
Touch the power-on button to
power on the lock Press down the handle to unlock
Note: Users may enter any random digits in front of and behind the correct password to create
random password to open the door. The maximum length of the random password is 32 digits.
Open the door with password
Swipe the card within
the induction zone
Enter the password,
press OK to confirm
Open the door with card
Press down the handle to unlock
Touch the power-on button to
power on the lock Press down the handle to unlock
Press down the handle to unlock

ZK Building, Wuhe Road, Gangtou, Bantian, Buji Town,
Longgang District, Shenzhen China 518129
Tel: [phone]
Fax: [phone]
www.zkteco.com
© Copyright 2017. ZKTeco Inc. ZKTeco Logo is a registered trademark of ZKTeco or a related company. All other product and company names mentioned are used
for identification purposes only and may be the trademarks of their respective owners. All specifications are subject to change without notice. All rights reserved.