Yale 8880 User manual

8800 Series Electrified Mortise Solenoid Locks
Installation Instructions
®
For Technical Assistance call Yale at 1-800-810-WIRE (9473)
Instructions for Wiring 8800 Series Electrified Mortise Solenoid Locks,
8800 Series Monitoring Suffixes REX, LBM & DBM
& Combined Solenoid & Monitoring Suffixes
with Pluggable "ElectroLynx Connector System"
NOTE TO INSTALLER
FAILURE TO FOLLOW THESE INSTRUCTIONS
COULD RESULT IN DAMAGE TO THE LOCK
AND VOID THE FACTORY WARRANTY.
Any retrofit or other field modification to a fire rated opening can
potentially impact the fire rating of the opening, and Yale Locks &
Hardware makes no representations or warranties concerning
what such impact may be in any specific situation. When
retrofitting any portion of an existing fire rated opening, or
specifying and installing a new fire-rated opening, please consult
with a code specialist or local code official (Authority Having
Jurisdiction) to ensure compliance with all applicable codes and
ratings.
An ASSA ABLOY Group brand
80-8800-0005-000 (07-14)

Introduction
This instruction manual includes wiring instructions for all electrical types of 8800 series electric mortise locks to
ElectroLynx Hinge Connector System. The correct wiring configuration must be selected depending on type and
function of the mortise lock being installed. Multiple functions can be combined (ex: 8890FL REX-LBM). Refer to
table on page 4 to select appropriate wiring instruction for mortise product being installed.
Important
Disconnect all input power before beginning installation to prevent electrical shock and equipment damage.
Installer must be a trained, experienced service person.
All wiring must comply with applicable local electrical codes, ordinances and regulations.
CAUTION: The DC voltage applied to the lock solenoid must not exceed If the voltage12 / 24 VDC +/- 10%
exceeds these values the solenoid may be damaged or not function.
Specifications / Functions
Solenoid
Type: 12 or 24VDC, Intermittent or Continuous Duty
612mA Peak @12VDC
500mA Steadystate @12VDC
330mA Peak @24VDC
612mA Steadystate @24VDC
Fail Safe: Models 8880, 8884, 8886, 8888, 8890, 8894-2, 8896 and 8898
Fail Secure: Models 8881, 8885, 8887, 8889, 8891,8895-2, 8897 and 8899
REX-, LBM-, and DBM- Lock Switches: contact rating for all switches: 2 Amp max @ 30VDC
REX (Request to Exit). Lever Monitor Switches. The 8800 REX series mortise lock is designed to allow monitoring of
inside and outside lever rotation. The lock uses two switches to monitor the inside and outside lever hubs.
LBM (latchbolt monitor switch). The 8800 LBM series mortise lock provides positive indication of latchbolt
extension or retraction when the lever is rotated retracting the latchbolt, latchbolt being retracted by key, or
if the latchbolt itself is depressed.
DBM (deadbolt monitor switch). The 8800 DBM series is designed to monitor the position of the dead bolt.
LPM (Lock Performance Monitor). The 8800 LPM series provides a status check on the lock’s main components.
2
Case
Cover
®
Molex Connectors:
8-Pin: Lock Options
4-Pin: REX
An ASSA ABLOY Group brand
80-8800-0005-000 (07-14)

C
Option A Sample wiring 8880 Thru 8899 series solenoid locks with a 12 or 24VDC Regulated and Filtered
Supply (Wiring shows power on and lock in secure state)Power
NO
Pigtail harness (Supplied with
McKinney Hinge)
(2 wires with 8-pin connector)
L N
Input
120VAC
60HZ
+ -
12 or 24VDC
Regulated and Filtered
Power Supply
(Recommended Securitron BPS series)
120VAC L/N/G
12 or
24VDC
GND
NC
Normally Closed Fire
Alarm Contact
(If Required)
8-wire
Electric Hinge
with 8-pin connectors
Installation and wiring instructions
Lock, raceway, electric hinge and pigtail 8-pin
terminations colors all match
1. Install door. Plug electric hinge and lock
connectors into raceway connectors.
2. Wire option A to pigtail harness.
3. Ensure proper supply voltage is
being applied at pigtail harness.
CAUTION: The DC voltage must not vary beyond
12V+/- 10% or 24V+/- 10%depending on lock
solenoid installed. If voltage exceeds these
values, the lock solenoid may be damaged or not
function.
4. Plug pigtail harness 8-pin connector into
electric hinge 8-pin connector.
5. Test lock - Applying 12 or 24VDC unlocks
fail secure applications and locks fail safe
applications.
Pigtail harness
(2 wires with
8-pin connector)
1
7 5
64
3
2
8
Red (+), 2
Black (-), 1
*Switch or
relay contacts
Installation Notes
1. With new applications a raceway harness with 8 and 4 pin connectors will be pre-installed inside door by ASSA
ABLOY door manufacturer when specified during ordering process. Raceway harness kits are available for retrofit
applications and for doors manufactured by non-ASSA ABLOY manufacturers.
2. Wiring to pigtail harness is per facility wiring requirement. Follow individual instructions below.
3. If door raceway connectors are not present, remove lock connector and wiring in Option A . follow
Plug into
8-pin hinge
connector
at door
1
7 5
64
3
2
8
Black (-)
Red (+)
Green
White
Orange
Brown
Yellow
Blue
1
7 5
64
3
2
8
Red (+), 2
Black (-), 1
Plug in
here
Note: Typical raceway location is
shown. Other locations may exist
depending on door type.
* NOTE: Wire 8880, 84, 86, 88, 90, 94-2, 96 & 98 (Fail Safe)
Locks to switch as shown. For 8881, 85, 87, 89, 91,
95-2, 97& 99 (Fail Secure) Locks wire NO (Normally Open)
contact to red wire of pigtail harness.
3
Raceway harness
with 8 & 4 pin
connectors
Options (8 wires)
REX (4 wires)
An ASSA ABLOY Group brand
80-8800-0005-000 (07-14)

REX
LBM
LPM
DBM
DB
DB-In
DB-Out
DPS
CX
* Deadbolt not available with DPS function.
Door Position Sensor
Cylinder Monitor
REFERENCES
Request to Exit
Latch Bolt Monitor
Latch Performance Monitor
Deadbolt Motintor
ELECTRIFIED OPTIONS
Deadbolt
Deadbolt Retracted
Deadbolt Extended
®
Molex
8-Pin Function Color Function Color
1,2 Power Black/Red Power Black/Red
LPM Green/Gray
LPM Green/Gray
LBM Green/Green
5,6 DB-In Yellow/Yellow CX Brown/Brown
7,8 DPS*
(Less DB) Blue/Blue DPS* Blue/Blue
4-Pin Function Color Function Color
1,2 Open Loop REX White/White Open Loop REX White/White
3,4 Closed Loop REX Gray/Gray Closed Loop REX Gray/Gray
3,4
8891-ITS8890 Options
-------------OR-------------
Yale® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Other products' brand names may be trademarks or registered trademarks of their
respective owners and are mentioned for reference purposes only. These materials are protected under U.S. copyright laws. All contents current at time of publication.
Yale Security Inc. reserves the right to change availability of any item in this catalog, its design, construction, and/or its materials.
Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
Product Support Tel 800.810.WIRE (9473) • www.yalelocks.com
Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company.
An ASSA ABLOY Group brand
80-8800-0005-000 (07-14)