Triton Blue T300-RGBAL User manual

T300-RGBAL
BASE RECORTE LED RGBAL
ENGINE MOTOR WITH RGBAL LED
MANUAL DE USUARIO / USER MANUAL
Este manual contiene información importante: léalo antes de poner el dispositivo en funcionamiento.

8.
english
User manual |T300-RGBALTriton Blue | January 2020 | www.triton-blue.com
INTRODUCTION
SAFETY INSTRUCTIONS
WARNING !!! To reduce the risk of fire, electric shock, or injury to persons, follow
these important safety instructions:
ENGLISH
Thank you for choosing our product, please read this instruction manual carefully and completely, and
keeps for reference use.This manual contains important information about the installation and usage of LED
zoom profile spotlight. Please comply with these relevant instructions strictly when install and use it. This
engine motor is made of aluminum alloy housing, high efficiency, energy saving and high durability.
Designed and produced strictly according to CE standard, compliance with international standard DMX512
protocol. For mounting a complete LED PROFILE, you need an optional additional lens (Ref. LENS-1530 or
LENS-2550). The complete LED profile Spot (T300-RGBAL + Lens) can be used in large- scale theatrical
performances, theatre, studio, Tego, hotels and other places.
WHAT IS INCLUDED?
The following items are included in the box:
1 xT300-RGBAL
1 x DMX512 3-pin signal cable - 2m
1 x Power cable with Powercom - 1.4m
1 x User Manual
Carefully unpack the carton, check the contents to ensure that all parts are present, and have been received
in good condition. Contact your supplier immediately and retain packing material for inspection if any part is
missing or damaged.
EQUIPMENT INSTALLATION AND MAINTENANCE
• Pay special attention to that if power supply voltage is consistent with the host marking, ensure that the voltage is
in the identified voltage range of technical parameters.
• DMX512 signal input and output of the lamp connector cable is connected together.
• Please check before use connected 220V AC, make sure the power switch socket wiring is good.To ensure the safety
use of the power, directly connect switch.The ground wire for the light is in yellow / green colour.
All the people related to the equipment installation and maintenance must:
• With electrical technician qualifications.
• The lamps have been strictly inspected before delivery.To ensure that these equipments are normal and safe ope-
ration, the user must comply with the following safety rules and precautions of this manual.
• Key: manufacturer is not responsible for the accident and loss raised by un-normal operation not in accordance
with this instruction or modify the equipment without permission.

9.
User manual |T300-RGBALTriton Blue | January 2020 | www.triton-blue.com
english
EQUIPMENT INSTALLATION AND MAINTENANCE
• Pay special attention to that if power supply voltage is consistent with the host marking, ensure that the voltage is in
the identified voltage range of technical parameters.
• DMX512 signal input and output of the lamp connector cable is connected together.
• Please check before use connected 220V AC, make sure the power switch socket wiring is good.To ensure the safety
use of the power, directly connect switch.The ground wire for the light is in yellow / green colour.
• When moving and installing the light, please avoid to knock the hard object of metal.
• Before usage, please check if the light is damaged or the screw is loose for transportation.
• Please install the light in the dry and ventilated environment of less than 40 ºC, and ensure the smooth flow of the
ventilation slots.
• When using the light, please keep more than 100 cm away from flammable objects, and light must be reliable con-
nected to grounding.
• When the lens of the light generates visible damage, such as cracks or deep marks, it should be replaced; bulbs
should be replaced when damaged or deformed.
• Prohibit to use over the range of rated technical condition.
• Prohibittooperatewith electricityandmustoperatedbyprofessionalpeople when install,connect,adjustandcheck.
• User can’t modify machine without permission, offenders should be responsible for the consequence.
• The correct method to clean the lens is to use vinegar or household ammonia, wet a clean thin cloth, gently wipe
the lens from the centre, also can use water to wipe, but after the water get dry there are some stains, which can be
gently wipe out with a clean dry cloth.
• When the electricity supply is cut off, the broken cable in the light end must be changed by the professional people
in time.The cable size is 3 x 1.5 square meter.
• Identification
Attention! Please replace the lens when it is visible damaged. Don’t use any glass,
window cleaner or hard cloth to clean the lens.
N
L

Earth line
NullWire
Phase line/ LiveWire
1.0 Front distance should be 1 meter.
Other side except front side distance should be 0.5 meter.
The light is not suitable to install directly in the surface of
the flammable material.
Recycle according to the European Union’s requirement
of WASTE ELECTRICAL AND ELECTRONIC

10.
english
User manual |T300-RGBALTriton Blue | January 2020 | www.triton-blue.com
1) Signal connection:
Connect the signal line of the lights when use the light (as following)
Master-slave mode connection method
The signal of LED zoom profile spotlights is connected in series; the number of each series is limited in 10. More than this
number, you need to consider the signal amplifier.
• Voltage: AC 210V- 230V, 50Hz
• Power: 300W LED module
• Power factor: 0.93
• Weight: 7,5kg
• Required lens (optional): 25/50 or 15/30
TECHNICAL PARAMETERS
• Master-slave control, multi-machine interconnected control (up to 10 per channel).
• DMX512 control, optional DMX address.
• 8 bit gray level 256 (approve single channel control), or you can specify 16-bit gray level 65535.
MAIN FUNCTION
INSTALLATION AND CONNECTION DIAGRAM (T300-RGBAL + Optional Lens)

11.
User manual |T300-RGBALTriton Blue | January 2020 | www.triton-blue.com
english
1. Set the address of DMX512
When using a DMX512 console to control the light, the light should be set up the address, ranging
from 1- 512. Press up / down button of Address, current state will be set to be controlled by
DMX512 signal control mode. Press the up / down button once, address will be add / subtract
once; when press up / down button longer, the address will fast continuous add and subtract.
Note: The address will be reserved automatically after operation stop for 10 seconds.
2. Manual host 16 bit dimming mode.
DMX512 console is not needed in this mode, but the light is set to be the host (console). It will
send DMX512 signal to control the lights connected with signal wire of same series, which makes
these light change the brightness accordant to the host.When using this function, one should pay
special attention to that no console’s signal connect, or there would be interference. Press the up /
down button of Dimmer, the current state is set to manual mode of host, 16- bit dimming mode.
single-press the up / down buttons, the brightness will be up / down once; when press up / down
button longer, the brightness will fast and continuously add and subtract ranging from 0- 65535.
Note: This state will be saved automatically after stop operating for 10 seconds.
USAGES AND OPERATIONS (T300-RGBAL + Optional Lens)
3. Manual test 16 bit dimming mode
The function of this mode is to test whether one single
light can be operated normally, it will not send DMX512
signal to influence the lights that connected with it. Press
up and down of Address at the same time, press up/ down
of Dimmer to dim, will display, XXXXX is the
brightness value when dimming, ranging from 0 to 65535.
Note: This state will not be reserved.
4. When the light is in the received state, it can’t
receive signal or can’t connect the signal wire, the backlight
of the liquid crystal display will flash, from which we can
know that if the connect wire is connected successfully.
5. Adjust the spot
Pull out four lighting adjusted slice (1) completely, connect
the power and control lighting. Adjust two focusing knob
can adjust the spot to different diameter. Tighten the
focusing knob (3) when you get the diameter you need and
the spot is clear.
6. Gobo
If you want to print some picture, firstly you should choose
the gobo holder of our company (the maximize range the
picture should beφ64. 5mm, outside diameter φ86mm).The
displayed picture is reversed. Put the gobo into gobo holder,
and then put it into the gobo notch (2). Lighten the light
and adjust the position of the focusing knob (3), image of
different diameter will display.Tighten the focusing knob (3)
when you get the diameter you need and the spot is clear.
7. Spot cutting
The spot of different shape will display when adjusting four
lighting adjusted slice (1). If you have special need, you can
unscrew the front device (4). The image can incline 45° by
turning the front device (5).
8 . Iris
If more spot of different diameter are needed, you can choose
our company’s iris. Loose the screw of the door (6) on the top
of the light, move forward to expose the bayonet, put the iris
inside, adjust the size of the iris, different size spot will display.
9 . Color film
If you need color rendering, clip the color paper with color
clamp, open the position (7) and put the color clamp in it. Or you
can use our company’s color change frame for profile spotlight,
controlled by DMX512 signal, RGBAL colors blending for more
brilliant color.

12.
english
User manual |T300-RGBALTriton Blue | January 2020 | www.triton-blue.com
DISPLAY FUNCTION TABLE SUBTRACT
Nº Display Function description
1 A001 9 channel address code (001-512)
up /down key change address code value
2 D001 5 channel address code (001-512)
up /down key change address code value
3 CC00 jump change (01-99)
up /down key change jump speed
4 CP00 gradually change (01-99)
up /down key modify the speed of gradient & pulse change
5 DE00 pulse change (01-99)
up /down key modify the speed of gradient & pulse change
6 BEB1 voice change
Nº Display Function description
7 R255 red choose color (000-255)
up /down key modify color
8 G255 green choose color (000-255)
up /down key modify color
9 B255 blue choose color (000-255)
up /down key modify color
10 A255 white choose color (000-255)
up /down key modify color
11 L255 yellow choose color (000-255)
up /down key modify color
DMX CHANNEL FUNCTION TABLE
Nº Display Function description
channel 1 R dimming R dimming, linear dimming, from dark to bright
channel 2 G dimming G dimming, linear dimming, from dark to bright
channel 3 B dimming B dimming, linear dimming, from dark to bright
channel 4 A dimming A dimming, linear dimming, from dark to bright
channel 5 L dimming L dimming, linear dimming, from dark to bright
A. Five channels function
Nº Display Function description
channel 1 Total dimming Total dimming, linaer dimming, from dark to bright
channel 2 Total strobe Total strobe ,from slow to fast
channel 3 Function
choice
0-50:DMX ( 8 channels control)
51-100:jump change
101-150:gradually change
151-200:pulse variable
201-255:voice
channel 4 Function speed Function speed ,from slow to fast
channel 5 R dimming R dimming, linear dimming, from dark to bright
channel 6 G dimming G dimming, linear dimming, from dark to bright
channel 7 B dimming B dimming, linear dimming, from dark to bright
channel 8 A dimming A dimming, linear dimming, from dark to bright
channel 9 L dimming L dimming, linear dimming, from dark to bright
B. Nine channels function

13.
User manual |T300-RGBALTriton Blue | January 2020 | www.triton-blue.com
english
WARRANTY
• Warranty service is only valid under normal use.
• All man-made damage, such as inadequate access to power, the use of
inappropriate accessories, non manual use, damage for transport and other
accidents, non- approved repair or modification, misuse or damage caused by
negligence, improper installation, are not in warranty.
• This warranty does not cover accessories, vulnerable parts, assistive devices,
transportation and maintenance personnel on- site service fee.
• When you can not solve the problem or have questions, please contact us.