Paramount Fitness ECO POOL 006-527-6316 Series User manual

AUTOMATIC IN-FLOOR CIRCULATION SYSTEM
INSTALLATION
8175 W. Buckeye Rd., Phoenix, AZ 85043
Toll Free: 1.800.621.5886 • Phone: [phone] • Fax: [phone]
[email protected] • www.1Paramount.com
US and Foreign patents and patents pending
see www.1paramount.com/support/patent-numbers/
Paramount products are designed by Paramount in Phoenix, Arizona, United States of America
004-027-8788-00 R00 ECN_2155 PUB081521 ©2021 Hayward Industries, Inc.

2
ECOPOOL RIBBED BODY SYSTEM
Item Number: 006-527-6315-XX
Includes:
(1) Two-Port Four-Gear Valve
(3) Ribbed Bodies with Cap
(3) Nozzles
(3) Riser Pipes
(1) Nozzle Tool
ECOPOOL SMOOTH BODY SYSTEM
Item Number: 006-527-6316-XX
Includes:
(1) Two-Port Four-Gear Valve
(3) Smooth Bodies with Cap
(3) Nozzles
(3) Riser Pipes
(1) Nozzle Tool
Please indicate your color choice by placing the appropriate color code in place of the “XX"
at the end of the part number.
White-01 Gray-02 Black-03 Light Blue-06 Beige-07 Light Gray-08

3
ECOPOOL EQUIPMENT AND PLUMBING SCHEMATIC
1 2
PUMP
48D.E.
SAND 4.9
MIN.FILTER
CART. 150
HEATER
optional
RETURNS NOZZLES
CANISTER MAIN DRAIN
SKIMMER
1 2
MIN.3'
1
1
1
2
2" COMES IN
FROM FILTER
3' MINIMUM
R RR
1
1 1
2 2 2
2
2
R
R
R
2" COMES IN
FROM FILTER
3' MINIMUM
R RR
MIN.3'
111
2
2
2
111
2 2 2
R
R
R
1 2
PUMP
48D.E.
SAND 4.9
MIN.FILTER
CART. 150
HEATER
optional
RETURNS NOZZLES
CANISTER MAIN DRAIN
SKIMMER
1 2
MIN.3'
1
1
1
2
2" COMES IN
FROM FILTER
3' MINIMUM
R RR
1
1 1
2 2 2
2
2
R
R
R
2" COMES IN
FROM FILTER
3' MINIMUM
R RR
MIN.3'
111
2
2
2
111
2 2 2
R
R
R
1 2
PUMP
48D.E.
SAND 4.9
MIN.FILTER
CART. 150
HEATER
optional
RETURNS
NOZZLES
CANISTER MAIN DRAIN
SKIMMER
1 2
MIN.3'
1
1
1
2
2" COMES IN
FROM FILTER
3' MINIMUM
R RR
1
1 1
2 2 2
2
2
R
R
R
2" COMES IN
FROM FILTER
3' MINIMUM
R RR
MIN.3'
111
2
2
2
111
2 2 2
R
R
R
VALVE PLUMBING SCHEMATIC
2 PORT WATER VALVE
1. Floor #1
2. Wall #2
Note: If EcoPool includes SwingJets #2 wall
fittings must be 1½" female threaded fittings with
no inside restrictions.
VALVE PLUMBING SCHEMATIC
2 PORT WATER VALVE
Min. Pump Curve
50 GPM @ 60 TDH
Min. Filter Size
36 SQ. FT. DE = 72 GPM
3.1 SQ. FT SAND = 60 GPM
100 SQ. FT. CARTRIDGE = 75 GPM
Additional features added to pool equipment
such as in-line feeders, water falls, etc., may
change the flow requirements. Changes in flow
requirements may require a higher GPM pump
and larger filtration
CENTER DEEP END DEEP

4
WATER VALVE INSTALLATION
ST
AGGER 3" MINIMUM
12
IN
NOTICE: All pipe fittings MUST be staggered.
PARTS NEEDED FOR ASSEMBLY
OPTION ONE
• (2) 2”X15” PVC PIPE (port 1,2)
• (1) 2”X18” PVC PIPE (port inlet)
• (3) 2” SLIP 90° ELBOWS
• Set in trench 15 “ deep X 12” wide
1. Remove clamp
2. Lift off dome (save O-ring)
3. Remove pressure gauge and knob from
inside valve housing assembly
4. Pipes and valve base should be treated with
primer
5. Make sure pipes are glued all the way into
the stop. Be careful not to allow glue to run
into module area.*
6. The center port is the inlet to the valve and
should be approximately 3” longer than the
perimeter pipes.
7. Allow 24 hour before pressure testing
8. Reposition o-ring in groove in the valve base.
9. Replace dome and V-Clamp and tighten until
snug
10. Thread the pressure gauge to the top of the
dome. Do Not Use Teflon Tape.
11. Pressurize with pool plumbing (do not
exceed 35 psi)
12. Store the module assembly in a safe place
and install after the pool has been started
up.
* Pipes should be a minimum of 12” in length
and should insure that valve be at least 6”
above water level.
Gluing instructions
PLUMBING & CONCRETE DETAIL
Gunite or Shotcrete Process
CONCRETE:
1. Make a cutout or opening approximately 1"
deep and 1" bigger than the pipe.
2. This cutout will be filled with plaster and create
a water stop.
Verify the angle of the risers as it is
imperative that the riser angle be 90 degrees
from the finished floor angle. Check that
the system did not lose pressure prior to
shooting the pool and upon completion.
PLUMBING FOR FLOOR NOZZLES
NOTE: All risers must be 90 degrees
(perpendicular) to the finished floor
2"SCH. 40 PIPE,
15"LONG
2"ELBOW 2"PIPE
1"X 1"CUTOUT
AROUND THE
PIPE FOR WATER
CUT PIPE HERE
SOIL
CONCRETE

5
PRE-PLASTER DETAIL | SMOOTH BODY INSTALLATION
1. Make a cutout or opening approximately 1"
deep and 1" bigger than the pipe. This cutout
will be filled with plaster or other finish coat to
create a water stop.
2. Cut off riser pipes flush with concrete
surface.
3. Remove cap. Prime the inside of the pipe.
DO NOT PRIME THE BODY.
4. Glue the body into the pipe with a regular
PVC glue.
The glue must cover the full length of the body
barrel and 3” deep inside the riser pipe. Push
the body into the pipe until the shoulder hits the
top edge of the pipe.
Let fumes vent for 30 minutes then replace all
body caps.
5. PLASTERING THE POOL
Leave all plaster caps in place for removal at
start up.
NOTE: Optional, the plaster crew may remove
the plaster caps as they finish.
NOTE: The body does not come with the
nozzle installed.
NOTICE: You can use regular PVC glue on smooth body
SOIL
CONCRETE