Trojan VERTIGO 250 Installation guide

www.trojanhealth.co.za
#1
HOME
FITNESS
SOUTH AFRICA’S
SINCE
1981
0861 876526
0861 TROJAN
WARRANTY
TROJAN
MY SPACE MY TIME
®
CAUTION
READ ALL PRECAUTIONS AND
INSTRUCTIONS IN THIS MANUAL
BEFORE USING THIS EQUIPMENT.
KEEP THIS MANUAL FOR
FUTURE REFERENCE

10211-3

10211-4

10211-5

10211-6
Part No. 21 x 2
Curved Washer (Ø19 x Ø8.4 x 1.5T)
Part No. 13 x 2
Spring Washer (M8)
Fixings
Part No. 32 x 2
End Cap Nut (M8)
Part No. 31 x 2
Carriage Bolt (M8 x 1.25P x 75)
Part No. 13 x 2
Spring Washer (M8)
Fixings
Part No. 21 x 2
Curved Washer (Ø19 x Ø8.4 x 1.5T)
Part No. 31 x 2
Carriage Bolt (M8 x 1.25P x 75)
Part No. 32 x 2
End Cap Nut (M8)
Part No. 82 x 1
Wheel Knob (M8 x 1.25P x 24)

10211-7
Fixings
Part No. 12 x 4
Round Head Allen Screw (M8 x 20)
Part No. 13 x 4
Spring Washer (M8)
Part No. 21 x 4
Curved Washer (Ø19 x Ø8.4 x 1.5T)
Fixings
Part No. 12 x 4
Round Head Allen Screw (M8 x 20)
Part No. 13 x 4
Spring Washer (M8)
Part No. 21 x 4
Curved Washer (Ø19 x Ø8.4 x 1.5T)
Fixings
Part No. 12 x 4
Round Head Allen Screw (M8 x 20)
Part No. 13 x 4
Spring Washer (M8)
Part No. 21 x 4
Curved Washer (Ø19 x Ø8.4 x 1.5T)
Fixings
Part No. 12 x 4
Round Head Allen Screw (M8 x 20)
Part No. 13 x 4
Spring Washer (M8)
Part No. 21 x 4
Curved Washer (Ø19 x Ø8.4 x 1.5T)
1
CAUTION:
Ensure that cables are not damaged
during assembly or when tightening screws.
CAUTION:
Ensure that cables are not damaged
during assembly or when tightening screws.

10211-8
Fixings
Part No. 65 x 4
Cap Nut (M6)
Pre-installed
Part No. 45 x 4
Flat Washer (Ø12 x Ø6.5 x 1.5T)
Pre-installed
Part No. 74 x 2
Plastic End Cap (M8)
Fixings
Part No. 74 x 2
Plastic End Cap (M8)
Part No. 75 x 2
Hex Head Bolt (M8 x 15)
Part No. 13 x 2
Spring Washer (M8)
Part No. 14 x 2
Flat Washer (Ø32 x Ø8.4 x 2.0T)
Part No. 15 x 2
Adjusting Washer (Ø32 x Ø19 x 0.5T)
Part No. 18 x 2
Curved Bushing (Ø32 x Ø19 x 13.5H)
Part No. 73 x 4
Plastic End Cap (M10)
Part No. 25 x 2
Hex Carriage Bolt (Ø12 x M10 x 1.5P x 80)
Part No. 79 x 2
Flat Washer (Ø24 x Ø13 x 1.5T)
Part No. 23 x 2
Cap Nut (M10 x 1.5P x 10H)
Part No. 24 x 2
Flat Washer (Ø20 x Ø11 x 2.0T)
Fixings
Part No. 65 x 4
Cap Nut (M6)
Pre-installed
Part No. 45 x 4
Flat Washer (Ø12 x Ø6.5 x 1.5T)
Pre-installed
Part No. 74 x 2
Plastic End Cap (M8)
Fixings
Part No. 74 x 2
Plastic End Cap (M8)
Part No. 75 x 2
Hex Head Bolt (M8 x 15)
Part No. 13 x 2
Spring Washer (M8)
Part No. 14 x 2
Flat Washer (Ø32 x Ø8.4 x 2.0T)
Part No. 15 x 2
Adjusting Washer (Ø32 x Ø19 x 0.5T)
Part No. 18 x 2
Curved Bushing (Ø32 x Ø19 x 13.5H)
Part No. 73 x 4
Plastic End Cap (M10)
Part No. 25 x 2
Hex Carriage Bolt (Ø12 x M10 x 1.5P x 80)
Part No. 79 x 2
Flat Washer (Ø24 x Ø13 x 1.5T)
Part No. 23 x 2
Cap Nut (M10 x 1.5P x 10H)
Part No. 24 x 2
Flat Washer (Ø20 x Ø11 x 2.0T)
5L
4L
3

10211-9
Fixings
Part No. 46 x 4
Hex Head Bolt (M6 x 1.25P x 38)
Part No. 43 x 4
Curved Washer (Ø12 x Ø6.4 x 1.5T)
Part No. 76 x 4
Spring Washer (M6)
Part No. 36 x 4
End Cap Nut (M6)
Fixings
Part No. 66 x 2
Plastic End Cap
Part No. 67 (R-Black / L) x 1 set
Lock Nut (M10 x 1.25P x 7H)
Part No. 68 x 2
Tooth Lock Washer
Fixings
Part No. 46 x 4
Hex Head Bolt (M6 x 1.25P x 38)
Part No. 43 x 4
Curved Washer (Ø12 x Ø6.4 x 1.5T)
Part No. 76 x 4
Spring Washer (M6)
Part No. 36 x 4
End Cap Nut (M6)
Fixings
Part No. 66 x 2
Plastic End Cap
Part No. 67 (R-Black / L) x 1 set
Lock Nut (M10 x 1.25P x 7H)
Part No. 68 x 2
Tooth Lock Washer
27L
5L
4L
19R

10211-10
Final Checks
Your cross trainer is now assembled. Please make the
following final checks before you use it for the first
time.
Make sure all screws / bolts are tightened.
Make sure you have positioned it on a flat,level
surface.
Ensure batteries (2 x AA)are installed in
computer. (Batteries not included)
Fixings
Part No. 12 x 3
Round Head Allen Screw (M8 x 20)
Part No. 13 x 3
Spring Washer (M8)
Part No. 21 x 3
Curved Washer (Ø19 x Ø8.4 x 1.5T)
Fixings
Part No. 83 x 4
Pan Head Philip Screw (M5 x 15)
Pre-installed on console
Recheck
all bolts and nuts are
tightened securely
before using the machine
8
3
CAUTION:
Ensure that cables are not damaged
during assembly or when tightening screws.

10211-11
USING THE C OMPUTER DESCRIPTION
Power On • Start pedalling or push the MODE button.
Power Off • Automatic shut off after 4 minutes of inactivity.
Mode Button • Press to select display functions.
TIME – SPEED – DISTANCE – CALORIES – HEART RATE
• Press and hold for 3 seconds to reset all functions to zero.
FUNCTIONS DESCRIPTION
SCAN • Automatically scans each function every 4 seconds in the following sequence.
TIME – SPEED – DISTANCE – CALORIES – HEART RATE
• To activate, press and release MODE button until SCAN appears on the display.
TIME • Displays the time from 1 second to 99.59 minutes.
SPEED • Displays the current speed from 0 to 99.9km per hour.
DISTANCE • Displays the distance from 0 to 999.9km.
CALORIES • Displays the calories consumption from 0 to 999.9kcal.
• The calories readout is an estimate for an average user. It should only be used as a comparison
between workouts on this unit.
HEART RATE • Displays your heart rate in beats per minute. To display heart rate, select HEART RATE mode
and grasp the pulse sensors on the handlebars, one in each hand. The heart symbol will
begin ashing when the computer senses your heart rate. Your heart rate will be displayed
approximately ve seconds after the heart icon is displayed. If you do not place your hands
correctly and 60 seconds passes without a heart rate reading, the computer will turn off the
heart rate circuit. If this occurs, press the MODE button to restart, place your hands back on
the pulse sensors correctly, and the heart rate readout will appear.

10211-12
Diagram 1
Diagram 2

10211-13

10211-14

10211-15
1
2
3
4
5

10211-16

10211-17
KEY NO. DESCRIPTION QTY
1 107 Front Post 1
2 02 Rear Post 1
3 03 Main Post 1
4 04 Handlebar Post 1p
5 05 Pedal Support Post2
6 06 Pedal Support Post Joint 2
7 07 Belt Support Wheel 1
8 08 Small Handlebar Post 1
9 09 Hand Pulse Sensor 2
10 10 Hand Pulse Sensor Cable 1
11 11 Round Head Self Tapping Screw (M14 x 15) 2
12 12 Round Head Allen Screw (M8 x 1.5P x 20) 11
13 13 Spring Washer (M8) 19
14 14 Flat Washer (Ø32 x Ø8.4 x 2.0T) 2
15 15 Adjusting Washer (Ø32 x Ø19 x 0.5T) 2
16 16 Sleeve (Ø32 x Ø26 x Ø19) 4
17 17 Console 1
18 18 Curved Bushing (Ø32 x Ø19 x 13.5H) 2
19 19 Upper Handlebar Post 1P
20 20 Tension Knob (8 Level) 1
21 21 Curved Washer (Ø19 x Ø8.4 x 1.5T) 15
22 108 Sensor Cable 1
23 23 Cap Nut (M10 x 1.5P x 10H) 2
24 24 Flat Washer (Ø20 x Ø11 x 2.0T) 2
25 25 Hex Carriage Bolt (Ø12 x M10 x 1.5P x 80) 2
26 26 Pedal (900) 1P
27 106 Main Cover 1P
28 28 End Cap 1
29 29 Wheel Foot Cap (Ø60) 2
30 30 Front Floor Support 1
31 31 Carriage Bolt (M8 x 1.25P x 75) 4
32 32 End Cap Nut (M8) 4
33 33 Metal Sleeve 4
34 34 Belt 1
35 35 High Density Handlebar Sleeve (Ø32 x 600
x 5.0)
2
36 36 End Cap Nut (M6) 4
37 37 Washer (Ø32 x Ø16.3 x 0.5T) 1
38 38 Round Head Self Tapping Screw (M5 x 15) 1
39 39 Split End Sensor Cable Set 1
40 40 Adjusting Assembly 2
41 41 Locknut (3/8” x 26W x 4H) 1
42 42 Locknut (3/8” x 26W x 7H) 3
KEY NO. DESCRIPTION QTY
43 43 Curved Washer (Ø12 x Ø6.4 x 1.5T) 4
44 44 Flat Washer (Ø25 x Ø8.2 x 1.5T) 2
45 45 Flat Washer (Ø12 x Ø6.5 x 1.5T) 4
46 46 Hex Head Bolt (M6 x 1.25P x 38) 4
47 47 Internal Bushing 4
48 48 Sphere Washer (Ø23 x Ø17 x 0.4T) 2
49 49 Double Sided Magnetic Wheel 1
50 50 Cap Nut (M10 x 1.5P x 7H) 2
51 51 End Cap (Ø1) 2
52 52 Countersunk Roller 1
53 53 Bushing (Ø16 x Ø10 x 18) 1
54 54 Sphere End Cap 2
55 55 Roller Secure Bracket 1
56 56 Flat Head Allen Screw (M10 x 1.5P x 40) 1
57 57 Spring (Ø17 x Ø2.3 x 83) 1
58 58 Bushing (Ø60) 2
59 59 Pan Head Phillip Screw (M5 x 0.8P x 60) 1
60 60 Foam Piece 2
61 61 Round Head Self Tapping Screw (M4 x 12) 8
62 62 Button Head Self Tapping Screw (M5 x 25) 4
63 63 Lower Adjusting Wire 1
64 64 Small Handlebar Sleeve 2
65 65 Cap Nut (M6) 4
66 66 Plastic End Cap 2
67 67 Lock Nut (M10 x 1.25P x 7H / R-Black / L) 1P
68 68 Tooth Lock Washer 2
69 69 C-Clip (Ø17) 2
70 70 Adjusting Washer (Ø22 x Ø17 x 0.5T) 1
71 71 Bearing 2
72 72 Pedal Support Post Joint Cap 2
73 73 Plastic End Cap (M10) 4
74 74 Plastic End Cap (M8) 4
75 75 Hex Head Bolt (M8 x 15) 4
76 76 Spring Washer (M6) 4
77 77 Round Head Allen Screw (M10 x 20) 1
78 78 Screw End Cap (M10 x 20) 2
79 79 Flat Washer (Ø24 x Ø13 x 1.5T) 2
80 80 Rear Floor Support 1
81 81 C-Clip 2
82 82 Wheel Knob (#24) 1
83 83 Pan Head Phillip Screw (M5 x 15L) 4
84 84 Tension Knob Support Post 1
85 85 Cable Pulling Extension 1

10211-18

10211-19

10211-20
0861 876526
0861 TROJAN