Trojan ELLIPTI-CYCLE 200 Installation guide

ELLIPTICAL TRAINER CARE INSTRUCTIONS
AND ASSEMBLY MANUAL
TROJAN
MY SPACE MY TIME
®
#1
HOME
FITNESS
SOUTH AFRICA’S
SINCE
1981
CAUTION
READ ALL PRECAUTIONS AND
INSTRUCTIONS IN THIS MANUAL
BEFORE USING THIS EQUIPMENT
KEEP THIS MANUAL FOR
FUTURE REFERENCE
1 YEAR
warranty
CALL
0861 876526
0861 TROJAN
ELLIPTI-CYCLE 200
ELLIPTICAL TRAINER

INDEX PAGE
1. SAFETY INSTRUCTIONS 3
2. PRE-ASSEMBLY CHECK LIST 4
3. HARDWARE LIST 5
4. ASSEMBLY STEPS 6
5. COMPUTER FUNCTIONS 9
6. FITNESSTIPS &TECHNIQUES 10
7. CONDITIONING GUIDELINES 11
8. WARM -UP AND COOL-DOWN 12
9. FREQUENTLY ASKED QUESTIONS 13
10. PARTS LIST 14
11. EXPLODED DRAWING 15
12. TROJAN 1YEAR LIMITEDWARRANTY 16
13. TROJAN REPAIRS PROCEDURE 18

1569-3
1.SAFETYINSTRUCTION
WARNING:
To reduce the risk of serious injury, read the following safety instruction before using theTROJAN ELLIPTI-CYCLE 200
ELLIPTICAL.
1.Use theTROJAN ELLIPTI-CYCLE 200 ELLIPTICAL only on a level surface.
2.Keep children and pets away from this equipment at all times.
3.TheTROJAN ELLIPTI-CYCLE 200 ELLIPTICAL should not be used by persons weighing more than 110kgs.
4.TheTROJAN ELLIPTI-CYCLE 200 ELLIPTICAL should be used by only one person at a time.
5.Be careful to maintain your balance while using,mounting,dismounting,folding,unfolding or assembling theTROJAN
ELLIPTI-CYCLE 200 ELLIPTICAL,loss of balance may result in a fall and serious bodily injury.
6.Use theTROJAN ELLIPTI-CYCLE 200 ELLIPTICAL only as described in the manual.
7.Do not attempt to adjust the seat cushion while you are on theTROJAN ELLIPTI-CYCLE 200 ELLIPTICAL.
8.Before using this equipment to exercise,always do stretching exercises to properly warm up.
9.Always make sure all bolts and nuts are tightened prior to each use.
WARNING
Before starting any exercise or conditioning program you should consult with your personal physician to see if you
require a complete physical exam.This is especially important if you are over the age of 35, have never exercised before,
are pregnant,or suffer from any illness.

1569-4
2.PRE-ASSEMBLYCHECKLIST
Thank you for choosing theTROJAN ELLIPTI-CYCLE 200 ELLIPTICAL.We take great pride in producing this quality
product and hope it will provide many hours of quality exercise to make you feel better, look better and enjoy life to its
fullest.
Yes,it’s a proven fact that a regular exercise program can improve your physical and mental health.Too often,our busy
lifestyles limit our time and opportunity to exercise.TROJAN ELLIPTI-CYCLE 200 ELLIPTICAL provides a convenient
and simple method to begin your assault on getting your body in shape and achieving a healthier lifestyle.
Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled.
• Read this manual carefully before using theTROJAN ELLIPTI-CYCLE 200 ELLIPTICAL.
Handlebar
U- Bar
Tension Knob
Computer
Seat Post
Front Stabilizer
Rear Stabilizer
Chaincover
Seat
Right Pedal

1569-5
3.HARDWARELIST
NOTE :
The described parts are all you need to assemble this machine.
Before starting assembly, please check the hardware packing to make sure they are included.
No. Description Q’ty
12 Carriage Bolt (M8 x 60mm) 4
11 Screw (M8 x 15mm) 8
14 Cap Nut (M8) 8
36 Washer (ø10 x 26mm) 4
15 ArcWasher (ø8 x 19mm) 16
68 Nut Cap (19#) 4
No. Description Q’ty
42 Carriage Bolt (M8 x 70mm) 4
53 Hex Head Screw (3/8”x 45mm) 4
39 Nylock Nut (3/8”) 4
M5 AllenWrench 1
M8 AllenWrench 1
Screw Driver
1

15
14
1
2
15
14 15
14
15
3
12
14
1
15
11 1
11
50
15
62 59A
59B
2
59A 59A
BA
59B
59B
68
6L
2
22L
44
6R
62
44 22L
68
1569-6
4.ASSEMBLYSTEP
STEP01
• Attach the Front Stabilizers (3) to the Main Frame (1) with
the Carriage Bolts (12),Washers (15) and Cap Nuts (14).
• Attach the Rear Stabilizers (76) to the Main Frame (1)
with the Carriage Bolts (12),Washers (15) and Cap Nuts
(14).
STEP 02
• Connect Sensor Cable (50) to the the Extention Cable
(62).
• Insert theTensionWire (59B) into the UprightTube (2)
• Secure the Handlebar Post by Screws (11) and
Washers (15).
• AttachTension Cable (59B) to theTension Controller
(59A) as shown in figureA and B.
STEP 03
• Attach the end of the Lower Handlebars (6L and 6R) to
the axle on the UprightTube (2) with theWashers (44)
Nylon Nuts (22L) and Nut Caps (68).
CAUTION:
Ensure that cables are not damaged
during assembly or when tightening screws.

22L
21
7
21
1
22R
7
39
7
36
8L
39
53
36
53
7
8R
6L
14
15
42
2
70
562
2
62
70
1569-7
STEP04
• Attach both PedalTubes (7) to the Cranks (21) with
Nylon Nuts (22L and 22R)
STEP05
• Connect the Pedals (8L and 8R) onto the PedalTubes (7)
with Nylon Nuts (39),Washers (36),and Hex Head Bolts
(3/8”x 45mm) (53).
• Each Pedal is marked“ L”for left side and “R”for right
side.
ASSEMBLYSTEP
STEP06
6.1.
• Insert the PulseWires (70) into the bigger hole on the
UprightTube (2) and pull them out from the top of the
UprightTube (2).
•Then attach the U-Style Bar (56) onto theTube (2) and
attach it with Screws (11) andWashers (15)
6.2
• Attach both Handlebars (5) onto the axles of the
Handlebar Post (2) and attach with Carriage Bolts (42),
Washers (15) and Nylon Nuts (14).
6.1 6.2
CAUTION:
Ensure that cables are not damaged
during assembly or when tightening screws.

51
64
54
55
41
4065
65
41
40
62
70
61
1569-8
ASSEMBLYSTEP
STEP07
• Attach the Seat (55) to the Seat Post (54) with attached Nuts (41),Washers (40) and
SpringWashers (65)
• Remove the Seat Knob (51), and then insert the Seat Post (64) into the Main Frame (1)
• Fix at the desired height with the Seat
Knob (51)
STEP08
• Connect the ExtensionWire (62) and PulseWire (70) with
theWires of the Computer (61).
• Attach the Computer (61) to the Handle Rod.
Recheck
all bolts and nuts are
tightened securely
before using the machine
CAUTION:
Ensure that cables are not damaged
during assembly or when tightening screws.

1569-9
5.COMPUTERFUNCTION
SPECIFICATIONS
TIME (TMR) 00:00-99:59
ODOMETER (IF HAVE) 0-9999 KM
SPEED (SPD) 0.0-99.9 KM/H
PULSE (IF HAVE) 40 - 240 BPM
DISTANCE (DST) 0.00-999.9 KM
CALORIES (CAL) 0-9999 KCAL
KEY FUNFCTION
MODE Use this key to select the particular function that you want
OPERATUION PROCEDURES
AUTO ON/OFF •The system turns on when any key is pressed or when it receives input from
the speed sensor.
•The processor turns off automatically when the speed sensor has no signal
input or no key is pressed for 4 minutes.
RESET The unit can be reset by changing the batteries or pressing the MODE key for
3 seconds.
HOWTOVIEWTIME,DISTANCE,
ODOMETER,PULSE & CALORIES Press the MODE key when the pointer is on the function you want which will start flashing.
FUNCTIONS TIME The exercise time will be displayed
by pressing MODE key untilTMR
appears.
SPEED Current speed will be shown by
pressing MODE key until SPD appear.
DISTANCE The distance of each workout will be
displayed by pressing MODE key until
DST appears.
ODOMETER Press the MODE key until the display
highlights ODO.The total accumulated
distance will be shown.
PULSE User’s current heart rate is displayed
in beats per minute (BPM) by pressing
MODE key until PULSE appears.Place
the palms of your hands on both
of the contact pads and wait for 30
seconds for the most accurate reading.
CALORIES The calories burned will be displayed
by pressing MODE key until CAL
appears.
SCAN Automatic display of the following
functions in the order shownTIME-
SPEED-DISTANCE-ODOMETER-
PULSE-CALORIES
BATTERY
This monitor uses twoAA batteries.If incorrect data displays on the monitor, please reinstall the batteries

1569-10
6.FITNESSTIPSANDTRCHNIQUES
AEROBIC EXERCISE
Aerobic exercise is any sustained activity that sends oxygen to your muscles via your heart and lungs.Aerobic exercise
improves the fitness of your lungs and heart - your body’s most important muscle.Aerobic exercise fitness is promoted
by any activity that uses your large muscle -arms,legs,or buttock,for example.Your heart beats quickly and you breathe
deeply. An aerobic exercise should be part of your entire exercise routine.
WEIGHTTRAINING
Along with aerobic exercising which helps get rid of and keep off the excess fat that our bodies can store, weight
training is an essential part of the exercise routine process.Weight training helps tone, build and strengthen muscle.
If you are working above your target zone,you may want to do a less amount of reps.And as always consult your
physician before beginning any exercise program.
MUSCLE CHART
ELLIPTICALTRAINER
The exercise routine that is performed on the elliptical trainer will develop the upper and lower body muscle group as
well as condition the circulatory system and provide a good aerobic workout .These muscle groups are highlighted on
the muscle chart below.

1569-11
EXERCISEINTENSITY
To maximize the benefits of exercising,it is important to exercise with the
proper intensity.The proper intensity level can be found by using your heart
rate as a guide.For effective aerobic exercise,your heart rate should be
maintained at a level between 65% and 85% of your maximum heart rate
as you exercise.This is known as your target zone.You can find your target
zone in the table below.
During the first few months of your exercise program,keep your heart rate near the low end of your target zone as you
exercise.After a few months,your heart rate can be increased gradually until it is near the middle of your target zone as
you exercise.
To measure your heart rate, stop exercising but continue moving your legs or walking around and place two fingers on
your wrist.Take a six-second heartbeat count and multiply the results by 10 to find your heart rate.For example, if your
six-second heartbeat count is 14,your heart rate is 140 beats per minute.(A six-seconds count is used because your
heart rate will drop rapidly when you stop exercising.)
Adjust the intensity of your exercise until your
heart rate is at the proper level.
For more information on dieting and
training visit www.trojanhealth.co.za
7.CONDITIONINGGUIDELINES
How you begin your exercise program depends on your physical condition. If you have been inactive for several years,or
are severely overweight,you must start slowly and increase your time on the equipment; a few minutes per workout.
Initially,you may be able to exercise only for a few minutes in your target zone,however, your aerobic fitness will improve
over the next six to eight weeks.Don’t be discouraged if it takes longer. It’s important to work at your own pace.Ulti-
mately,you’ll be able to exercise continuously for 30 minutes.The better your aerobic fitness,the harder you will have to
work to stay in your target zone.Please remember these essentials :
• Have your doctor review your training and diet programs to advise you of a workout routine you should adopt.
• Begin your training program slowly with realistic goals that have been set by you and your doctor.
• Monitor your pulse frequently.Establish your target heart rate based on your age and condition.
• Set up your equipment on a flat,even surface at least 3 feet from walls and furniture.

1569-12
8.WARM-UPANDCOOL-DOWN
WORKOUTGUIDELINES
Each workout should include the following three parts:
A warm-up,consisting of 5 to 10 minutes of stretching and light exercise.A proper warm-up increases your body tem-
perature,heart rate,and circulation in preparation for exercise.
Training zone exercise,consisting of 20 to 30 minutes of exercising with your heart rate in your training zone. (Note:
During the first few weeks of your exercise program,do not keep your heart rate in your training zone for longer than
20 minutes.)
A cool-down,with 5 to 10 minutes of stretching.This will increase the flexibility of your muscles and will help to prevent
post-exercise problems.
EXERCISEFREQUENCY
To maintain or improve your condition, plan three workouts each week,with at least one day of rest between workouts.
After a few months of regular exercise,you may complete up to five workouts each week,if desired.Remember, the key
to success is make exercise a regular and enjoyable part of your everyday life.
SUGGESTEDSTRETCHES
The correct form for several basic stretches is shown at the right.Move slowly as you
stretch-never bounce.
1.ToeTouch Stretch
Stand with your knees bent slightly and slowly bend forward from your hips.Allow
your back and shoulders to relax as you reach down toward your toes as far as
possible. Hold for 15 counts,then relax. Repeat 3 times.Stretches:Hamstrings,
back of knees and back.
2.Hamstring Stretch
Sit with one leg extended.Bring the sole of the opposite foot toward you and rest it
against the inner thigh of your extended leg.Reach toward your toes as far as
possible. Hold for 15 counts,then relax. Repeat 3 times for each leg.Stretches:
Hamstrings,lower back and groin.
3.Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your hands against a
wall.Keep your back leg straight and your back foot flat on the floor. Bend your
front leg,lean forward and move your hips toward the wall.Hold for 15 counts,
then relax.Repeat 3 times for each leg.To cause further stretching of the achilles
tendons,bend your back leg as well.Stretches:Calves,achilles tendons and ankles.
4.Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp one foot with your
other hand.Bring your heel as close to your buttocks as possible.Hold for 15 counts,
then relax.Repeat 3 times for each leg.Stretches:Quadriceps and hip muscles.
5.InnerThigh Stretch
Sit with the soles of your feet together and your knees outward.Pull your feet
toward your groin area as far as possible.Hold for 15 counts,then relax.Repeat 3
times.Stretches:Quadriceps and hip muscles.
For more information on dieting and training visit www.trojanhealth.co.za
1
2
3
4
5

1569-13
9.FREQUENTLYASKEDQUESTIONS
Q1. My elliptical does not move as easily as indicated in manual
1. Ensure you have placed the stabilizer with the wheels in the front of the unit.
Q2. My consol does not work?
1. Make sure you have connected it correctly and have placed the batteries in the consol.
Q3. My consol is not clear and appears faded?
1. Ensure your unit is not in direct sunlight and you have removed the plastic cover from the screen.
If display does not improve,please contact 0861 876 526
Q4. My tension control is not working?
1. Ensure the cable has been connected correctly
Q5. My pedals are not fitting properly?
1. Make sure you have inserted them on the correct side of the unit.Each pedal is marked L or R.
Q6. I cannot thread the main cable through the upright bar?
1. Use the thin wire provided or a piece of string to assist you.
Q7. My consol is showing a “0” error
1.Check that the sensor magnet is correctly fitted and passes in front of the sensor.
2.Check the gap between speed sensor and the magnet is 5mm or less
3.Check that all computer plugs and sockets are firmly and correctly connected
4.Check that the computer wires are not damaged
If the error persists, please contact 0861 876 526
Q8. The consol cannot read the hand pulse signal
1. The hand pulse sensors will not operate correctly if your skin is extremely dry.Moisten your hands and try again.
2.Avoid moving your hands while exercising and hold the hans pulse sensors firmly while exercising.If you do move your
hands while exercising,give the computer a few seconds to resample and display your correct heart pulse rate
3.Clean the hand pulse sensors to ensure good contact between your body and the pulse sensor
If the error persists, please contact 0861 876 526

1569-14
10.PARTSLIST
No. Description Q’ty
1569-01 Main Frame 1
1569-02 Upright Post 1
1569-03 Front Stabilizer (ø50 x 1.5 x 500) 1
1569-04 Flywheel 1
1569-05 Upper Handlebar 2
1569-06-L Lower Handlebar (L) 1
1569-06-R Lower Handlebar (R) 1
1569-07 PedalTube 2
1569-08-L Pedal (L) 1
1569-08-R Pedal (R) 1
1569-09 Wheen Cap (ø50) 2
1569-10 End Cap (ø50) 2
1569-11 Bolt (M8 x 15mm) 8
1569-12 Carriage Bolt (M8 x 60mm) 4
1569-13 Washer (ø8 x ø19 x 1.5) 1
1569-14 Nut Cap (M8) 8
1569-15 ArcWasher (ø8 x ø19 x 1.5) 16
1569-16 Bearing (L) 1
1569-17 Bearing (R) 1
1569-18 Magnet (ø12.5 x 5mm) 1
1569-19 Pulley (ø240) 1
1569-20 Belt 1
1569-21 Crank (1pc) 1
1569-22-L Nylon Nut (1/2”x 20T) 1
1569-22-R Nylon Nut (1/2”x 21T) 5
1569-23 Plastic Spacer (ø16 x ø25 x 22) 2
1569-24 Plastic Roll (ø16 x ø30.5) 6
1569-25 Chromed Bearing (ø15.8) 4
1569-26 Rear Pedal Axle (L) 1
1569-27 Rear Pedal Axle (R) 1
1569-28 Bearing (6000zz) 2
1569-29 Flywheel Spacer (ø10 x ø13 x 10) 1
1569-30 BC Nut (3/8”) 1
1569-31 Washer (ø10 x ø19 x 1.5) 1
1569-32 Nut (3/8”) 1
1569-33 Greased Bearing (ø8 x ø13 x 6) 1
1569-34 FlywheelAxle (ø9.98 x 126) 1
1569-35 Nylon Nut (M8) 2
1569-36 Washer (ø10 x 26 x 1.5) 4
1569-37 Lower Handlebar Cap 2
No. Description Q’ty
1569-38 Adjust Knob (M8) 1
1569-39 Nylock Nut (3/8”) 4
1569-40 Washer (ø8) 4
1569-41 Nylock Nut (M8) 4
1569-42 Carriage Bolt (M8 x 70mm) 4
1569-43 Square Plug (38.1 x 38.1mm) 2
1569-44 Washer (ø13 x 26 x 2.0) 4
1569-45 Zip (M6 x 40mm) 2
1569-46 Magnetic Plate 1
1569-47 Plate Spring (ø1.5 x ø14.5 x 64) 1
1569-48 Hex Head Bolt (M8 x 60mm) 2
1569-49 Nut (M8) 2
1569-50 SensorWire (1350mm) 1
1569-51 Seat Adjust Knob 1
1569-52 Seat Bushing 1
1569-53 Hex Head Bolt (3/8”x 45mm) 4
1569-54 Seat U- Plate (38.1 x 38.1mm) 1
1569-55 Seat (CY-207) 1
1569-56 U-bar (ø28.6) 1
1569-57 Foam Grip (ø28.6) 2
1569-58 Bolt (M6 x 10mm) 2
1569-59-A Tension Knob 1
1569-59-B Tension Cable (1350mm) 1
1569-60 Tension Bolt (M5) 1
1569-61 Computer 1
1569-62 ExtensionWire (1200) 1
1569-63 Round Cap (ø28.6) 2
1569-64 Seat Post 1
1569-65 SpringWasher 4
1569-66 Foam Grip 2
1569-67 Handlebar Cap (ø28.6) 2
1569-68 Plastic Cap 4
1569-69 Plastic Roll (Slant) 2
1569-70 PulseWire 2
1569-71 Bolt (M4 x 16mm) 9
1569-72 Bolt 1
1569-73 Plastic Cover (L) 1
1569-74 Plastic Cover (R) 1
1569-75 Crank Cap 2
1569-76 Rear Stabilizer 1

48
31
32
2
46
30
45
29
47
28 4
42
61
68
7
36
24
24
22L
44
52
51
58
64
58
13
38
41 43
65
41 40 65
55
43
54
23
71
11
45
15
49
16
25 21
26
39
25
23 22L
76
10
35
28
33
34
14
15
48
12
10
14
8L
37
53
14
15
15
15
19
14
1
20
18
17
50
21
22R
35
27
44
15
14 22L
2
22L
6L
68
44 15
50 11
15
62 59B
14
24
42 36 69
60 59A
72
8R
7
39
37
36
25
25
24
6R 24
66
5
69
36
68
44
24
68
22L
53
71
71
75 67
71 71
73
71
5
71
74
71
75
67
1569-15
11.EXPLODEDDRAWING

1569-16
12.TROJAN1YEARLIMITEDWARRANTY
Masstores (Pty)Ltd (“the Supplier”) hereby provides a limited warranty to the original purchaser of this product (“the
Consumer”) thatthisproductwillbe freeofmanufacturing defectsin materialsandworkmanshipwhich undernormal,
personal,familyorhouseholduse(commercialuseexpresslyexcluded)manifestthemselveswithinthefollowingstipu-
lated periods from the date of purchase:
Exclusions
The warranty does not include and will not be construed to cover products damaged as a result of disaster; misuse;
commercial use; use not in accordance with the written instructions included with the product; abuse; and/or any
non-authorizedmodicationoftheproduct.Italsodoesnotcoverreplacementofthelightbulbsandotherexpendables.
All demo models carry a 3 month warranty.
Waiver
The warranty provided herein and the obligations of the Supplier are in lieu of, and the Customer waives, all other war-
ranties,guarantees,conditionsorliabilities,expressorimplied,arisingbylaworotherwise,includingwithoutlimitation,any
obligation of the Supplier in respect of any injury , loss or damage (direct, indirect or consequential) arising out of the
useof,orinabilitytouse,thisproductandwhetherornotoccasionedbytheSupplier’snegligenceoranyactoromission
on its part.
Claims under 1 Year Limited Warranty
Within 7 days of purchase:
The faulty product will be exchanged (provided that the product is in its original packaging with all accessories).
After 7 days but within 3 months of purchase:
The Supplier may in its sole discretion either replace or repair the product.
After 3 months but within 1 year of purchase:
The Supplier may in its sole discretion either replace or repair the product. The following shall not be covered:
t Treadmills: Running Decks, Running Belts, and Rubber Arm covers
t Exercise Bikes/Spinners: Pedals, Cranks, and Rubber Arm covers
t Cross Trainers/ Ellipticals/ Steppers: Foot Rests, Cranks, Shocks, and Rubber/Foam Arm covers
t Home Gyms: Pulleys, Cables, Seats and Padding
t Trampolines: Springs, Mats, and Covers
t Rowers: Rowing Strap / Rope / Arms, Pulling Handle, Grip, Moveable Seat
Parts not mentioned in the above, are covered under warranty within the 1st year of purchase

1569-17
Proof of Purchase
Any claim in terms of the warranty must be supported by a proof of purchase or a warranty number.
Warranty numbers can be issued through contacting our call centre on 0861 Trojan (0861 876 526),
or online at www.trojanhealth.co.za.If such proof is not available, then notwithstanding anything to the
contrary herein,the service agent’s prevailing charges for services/repairs including call-out and/or spares will
be payable by the Consumer upon collection or delivery of the repaired product.
The Consumer does not need to return the product to the store.
The Consumer shall phone theTrojan hotline on 0861 Trojan (0861 876 526) and the Supplier’s authorized agent
will at its discretion either repair the item at the Consumer’s residence or collect and repair the item at their premises.
During the warranty period the product may only be serviced and/or repaired by the Supplier’s duly
authorized agent(s).
Masstores (Pty) Ltd
16 Peltier Drive,Sunninghill
Sandton, Johannesburg, South Africa

1569-18
13.TROJANREPAIRSPROCEDURE
1.Procedure for repairs
Should you experience any faults or breakdowns on yourTrojan equipment,please adhere to the following procedure
to have the fault rectified speedily and professionally.
• Do not return the product to the store*
• Call 0861 Trojan (0861 876526) to log the faulty product (under warranty or out of warranty)
• The operator or technical advisor will try identify the fault,and will book a service team call out.
• The service team will endevour to fix the problem in your home on an agreed date and time.
• Only if the fault cannot be repaired in the convenience of your home,will the service team take the
faulty product back to the service centre.
• Items repaired in our service centre will be returned to your home on an agreed date and time.
* Note:
Should you live in an outlying area,it may be neccessary to return the product to the store nearest to you.Our service
operator will advise you of your repair procedure.
2.Cost of Repairs
2.1 Under warranty
• Any items still under warranty will be repaired free of charge,as long as it complies with the terms and
conditions of the warranty. (refer to“warranties” section in this manual)
• Any items that need to be repaired that are NOT covered in the warranty will be for the consumer’s
expense.A quote for the repair/replacement of these items will be provided to the consumer for ap
proval prior to repairs being conducted.
2.2 Out of Warranty
• Any items that need to be repaired once the warranty has expired will be for the consumer’s expense
including call out fees.A quote for the repair/replacement of these items will be provided to the
consumer for approval prior to repairs being conducted.

1569-19

1569-20