Trust START-LINE ACD-2400 User manual

START-LINE
RECEIVER ACD-2400
MAINS SOCKET SWITCH
USER MANUAL
SMART Home
Version 1.0
Visit www.trustsmarthome.com
for the most recent user manuals

2
ACD-2400 MAINS SOCKET SWITCH
COMPATIBILITY
This receiver works with all
trust smart h
ome
transmitters.
FUNCTIONALITY
Mains socket switch to switch lights or electronic
devices on/o up to 2400 Watt.
WIRELESS RADIO SIGNAL
• The 433.92 MHz radio signal passes through walls, windows and doors.
• Indoor range: up to 30 m. Outdoor range: up to 70 m. (optimal conditions)
• The range is strongly dependent on local conditions, such as the presence of metals. For example,
the thin metal coating in Low-emissivity (Low-E) glass has a negative impact on the range of radio
signals.
TECHNICAL SPECIFICATIONS
Power supply input 220-240 VAC 50 Hz
Maximum load 2400 Watt
RF frequency 433,92 MHz
RF range Up to 30m indoor/ 70m outdoor (optimal conditions)
Memory addresses 6

3
ACD-2400 MAINS SOCKET SWITCH
MAXIMUM LOAD
Never connect lights or equipment that exceed
the maximum load of the receiver, as it can result
in defects.
SHOCK HAZARD
Caution when installing a receiver. Voltage may
be present, even when a receiver is switched o.
LIFE-SUPPORT
Never use
trust smart h
ome products for life-
support systems or other applications in which
equipment malfunctions can have life-threatening
consequences.
INTERFERENCE
All wireless devices may be subject to
interference, which could aect reception. The
minimum distance between 2 receivers should be
at least 50 cm.
REPAIRING
Do not attempt to repair this product. There are
no user-serviceable parts inside.
WATER-RESISTANCE
This product is not water-resistant. Keep it dry.
Moisture will corrode the inner electronics and
can result in a short circuit, defects and shock
hazard.
CLEANING
Use a dry cloth to clean this product. Do not use
harsh chemicals, cleaning solvents, or strong
detergents.
HANDLING
Do not drop, knock, or shake the device. Rough
handling can break internal circuit boards and fine
mechanics.
ENVIRONMENT
Do not expose the product to excessive heat
or cold, as it can damage or shorten the life of
electronic circuit boards.
Read this manual carefully. Not following them may be dangerous and faulty installation will invalidate
any warranty that may apply to this product.

4
1. Connect lamp/device and place the
main socket switch
First check if the lamp or device is turned
on. Then plug the lamp or device into the
receiver and plug the receiver into a socket.
Do not exceed the maximum load: 2400 W
2a. Assign transmitter code
Press the learn-button on the receiver for 1
second. The learn-mode will be active for 15
seconds, during which the LED-indicator will
blink slowly.
ACD-2400 MAINS SOCKET SWITCH
1 sec.

5
2b.
Send an ON-signal with any
trust smart h
ome
transmitter while the learn-mode is active, to
assign the code to the receiver’s memory.
The receiver will switch on/o 2 times to con-
firm the code has been received. The receiver
can store up to 6 dierent transmitter codes
in its memory.
The memory will be preserved when the
receiver is moved to another socket or in case
of power failure.
2c.
ON
ON
ON
ACD-2400 MAINS SOCKET SWITCH
2x

6
3. Manual operation with a transmitter
1. Send an ON-signal to switch the receiver on.
2. Send an OFF-signal to put the receiver in stand-by.
ACD-2400 MAINS SOCKET SWITCH

7
Single code delete
1. Press the learn-button for 1 second. The learn-mode will be active for 15 seconds, during which
the LED-indicator will blink slowly.
2. While the learn-mode is active, send an OFF-signal of a specific
trust smart h
ome transmitter
to delete that code.
3. The receiver will switch on/o 2 times to confirm code deletion.
1 sec.
ACD-2400 MAINS SOCKET SWITCH
2x
OFF

8
1. Press and hold the learn-button of the receiver (approx. 7 sec.) untill the LED-indicator starts
blinking fast. The delete mode will be active for 15 seconds.
2. Press the learn-button again for 1 second while the delete mode is active.
3. The receiver will switch on/o 2 times to confirm memory deletion.
Full memory delete
2x
7 sec. 1 sec.
ACD-2400 MAINS SOCKET SWITCH

9
Trust International B.V. declares that this product is in compliance with the essential
requirements and other relevant provisions
WEEE: If possible, dispose of this product at a recycling center. Do not dispose of this product
with the household waste.
Warranty
This product is covered by the legal warranty that applies to your country and it begins on the day of
purchase. For additional information, visit: www.trustsmarthome.com/warranty/
Copyright
The contents of this user manual are subject to copyright protection. Without prior written permission,
reproducing or copying is prohibited. Information in these documents is subject to change without
prior notice. Check www.trustsmarthome.com for updates.
ACD-2400 MAINS SOCKET SWITCH

10
Declaration of conformity
Trust International B.V. declares that the
trust smart h
ome product:
model: ACD-2400 MAINS SOCKET SWITCH
item number: 75002
intended use: indoor
is in compliance with the essential requirements and other relevant provisions of the following
directives: EMC Directive, Low Voltage Directive and R&TTE Directive.
The product is compatible with the following norms/standards:
Manufacturer/Authorised representative,
H. Donker, Procurement Director
Dordrecht, 28 November 2014
Trust International B.V.
P.O. BOX 434
3300 AK DORDRECHT
THE NETHERLANDS
www.trustsmarthome.com
AS/NZS 4268: 2012 +A1:2013
CISPR 15: 2013
AS/NZS CISPR 15:20111
ERHE Standard: 2003
ARPANSA: MELRF- 3kHZ to 300 GHz
AS/NZS 3122:2005 (fifth edition)
AS/NZS 3197:2005 (second edition) + Amendemt
NO. 1:2007 + Amendment No. 2:2012
ACD-2400 MAINS SOCKET SWITCH