Tyco ELO-231FRB Series User manual

General
Description
The 11.2 K-factor, Series ELO-
231FRB, Quick Response, Standard
Coverage, Upright and Pendent Sprin-
klers (Ref. Figure 1) are automatic
sprinklers of the frangible bulb type.
They are “quick response - spray
sprinklers” that produce a hemispheri-
cal water distribution pattern below the
deflector.
The 11.2 K-factor, ELO-231FRB Up-
right and Pendent Sprinklers were
subjected to full scale, high-piled stor-
age,fireteststo qualify their use in lieu
of 5.6 or 8.0 K-factor standard spray
sprinklers for the protection of high-
piled storage.
Higher flow rates can be achieved at
much lower pressures with the 11.2
K-factor, ELO-231FRB Sprinklers —
making their use highly advantageous
in high density applications, such as
the protection of high-piled storage.
For in-rack applications an upright in-
termediate level version of the Series
ELO-231FRB Sprinklers can be ob-
tained by utilizing the Series ELO-
231FRB Upright Sprinkler with the
WSG-2Guard&Shield,andapendent
intermediate level version of the Se-
ries ELO-231FRB Sprinklers can be
obtained by utilizing the Series
ELO-231FRB Pendent Sprinkler with
theWS-2Shield.Ifthereisapossibility
of the pendent intermediate level ver-
sion being exposed to mechanical
damage, a G-2 Guard can be added.
WARNINGS
The 11.2 K-factor, Series ELO-
231FRB Upright and Pendent Sprin-
klers described herein must be in-
stalled and maintained in compliance
with this document, as well as with the
applicable standards of the National
FireProtectionAssociation,inaddition
to the standards of any other authori-
ties having jurisdiction. Failure to do
so may impair the performance of
these devices.
The owner is responsible for maintain-
ing their fire protection system and de-
vices in proper operating condition.
The installing contractor or manufac-
turer should be contacted with any
questions.
Installation of Series ELO-231FRB
Pendent Sprinklers in recessed es-
cutcheons will void all sprinkler war-
ranties, as well as possibly void the
sprinkler’s Approvals and/or Listings.
Model/Sprinkler
Identification
Numbers
TY5131 - Upright 11.2K, 3/4"NPT
TY5231 - Pendent 11.2K, 3/4"NPT
TY5131 is a redesignation for C5131.
TY5231 is a redesignation for C5231,
G1870, and S2551.
Series ELO-231FRB — 11.2 K-factor
Upright and Pendent Sprinklers
Quick Response, Standard Coverage
Page 1 of 4 TFP344
MARCH, 2007
Technical Services: Tel: [phone] / Fax: [phone]
IMPORTANT
Always refer to Technical Data
Sheet TFP700 for the “INSTALLER
WARNING” that provides cautions
with respect to handling and instal-
lation of sprinkler systems and com-
ponents. Improper handling and in-
stallation can permanently damage
a sprinkler system or its compo-
nents and cause the sprinkler to fail
tooperateina fire situation or cause
it to operate prematurely.

Technical
Data
Approvals
UL and C-UL Listed. FM and NYC Ap-
proved. (Refer to TableA for complete
approval information including corro-
sion resistant status. The approvals
apply to the service conditions indi-
cated in the Design Criteria section.)
Maximum Working Pressure
175 psi (12,1 bar)
Discharge Coefficient
K = 11.2 GPM/psi1/2
(161,4 LPM/bar1/2)
Temperature Ratings
RefertoTableA
Finishes
Sprinkler: Refer to Table A
Physical Characteristics
Frame . . . . . . . . . . . . . Bronze
Cap . . . . . . . . . . . . . . Bronze
SealingAssembly ..........
. . . . . Beryllium Nickel w/Teflon†
Bulb(3mmdia.)........Glass
Compression Screw . . . . . Bronze
Deflector . . . . . . . . . . . Bronze
† Registered trademark of DuPont.
Design Criteria
ULandC-ULListing
Requirements
The 11.2 K-factor, Model ELO-
231FRB (TY5131 & TY5231) Sprin-
klers are to be installed in accordance
with NFPA 13 standard sprinkler posi-
tion and area/density flow calculation
requirements for light, ordinary, or ex-
tra hazard occupancies, as well as
high piled storage occupancies (solid
piled, palletized, rack storage, bin box,
and shelf storage including but not lim-
ited to Class I-IV and Group Aplastics)
with a minimum residual (flowing)
pressure of 7 psi (0,5 bar) for wet pipe
systems only.
FM Approval
Requirements
The 11.2 K-factor, Model ELO-
231FRB (TY5131 & TY5231) Sprin-
klers are to be installed in accordance
with the applicable “control mode den-
sity/area” guidelines provided by Fac-
tory Mutual for wet systems only. (FM
guidelines may differ from UL and C-
UL Listing criteria.)
Operation
The glass bulb contains a fluid that
expands when exposed to heat. When
the rated temperature is reached, the
fluid expands sufficiently to shatter the
glass bulb, allowing the sprinkler to
activate and water to flow.
Installation
The Series ELO-231FRB Sprinklers
must be installed in accordance with
the following instructions:
NOTES
Do not install any bulb type sprinkler if
the bulb is cracked or there is a loss of
liquid from the bulb. With the sprinkler
held horizontally, a small air bubble
should be present.The diameter of the
air bubble is approximately 1/16 inch
(1,6 mm) for the 155°F/68°C to 3/32
inch (2,4 mm) for the 286°F/141°C
temperature ratings.
A leak tight 3/4 inch NPTsprinkler joint
should be obtained with a torque of 10
to 20 ft.lbs. (13,4 to 26,8 Nm). A maxi-
mum of 30 ft.lbs. (40,7 Nm) of torque
is to be used to install sprinklers with
3/4 NPT connections. Higher levels of
torque may distort the sprinkler inlet
and cause leakage or impairment of
the sprinkler.
Do not attempt to make-up for insuffi-
cient adjustment in the escutcheon
plate by under- or over-tightening the
sprinkler. Readjust the position of the
sprinkler fitting to suit.
The Series ELO-231FRB Upright
and Pendent Sprinklers must be in-
stalled in accordance with the follow-
ing instructions.
Step 1. Pendent sprinklers are to be
installed in the pendent position, and
upright sprinklers are to be installed in
the upright position.
Step 2. With pipe thread sealant ap-
Page2of4 TFP344
TYPE TEMPERATURE BULB
LIQUID NATURAL BRASS
SPRINKLER FINISH
NOTES:
1. Listed by Underwriters Laboratories, Inc. (UL Listed).
2. Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL Listed).
3. Approved by Factory Mutual Research Corporation (FM Approved).
4. Approved by the City of New York under MEA 291-04-E.
TABLE A
LABORATORY LISTINGS AND APPROVALS
FOR 11.2 K-FACTOR SERIES ELO-231FRB UPRIGHT AND PENDENT SPRINKLERS
(Refer to the Design Criteria Section)
UPRIGHT
(TY5131) 1, 2, 3, 4
155°F/68°C Red
200°F/93°C Green
286°F/141°C Blue
CHROME
PLATED
155°F/68°C
200°F/93°C
286°F/141°C
PENDENT
(TY5231)
Red
Green
Blue
1, 2, 3, 4

plied to the pipe threads, hand tighten
the sprinkler into the sprinkler fitting.
Step 3. Tighten the sprinkler into the
sprinkler fitting using only the W-Type
3 Sprinkler Wrench (Ref. Figure 2).
Withreference to Figure1,theW-Type
3 Sprinkler Wrench is to be applied to
the wrench flats.
Care and
Maintenance
Series ELO-231FRB Sprinklers must
be maintained and serviced in accord-
ance with the following instructions:
NOTES
Before closing a fire protection system
control valve for maintenance work on
the fire protection system that it con-
trols, permission to shut down the af-
fected fire protection system must be
obtained from the proper authorities
and all personnelwho may be affected
by this action must be notified.
Sprinklers that are found to be leaking
or exhibiting visible signs of corrosion
must be replaced.
Automatic sprinklers must never be be
painted, plated, coated or otherwise
altered after leaving the factory. Modi-
fied sprinklers must be replaced.
Sprinklers that have been exposed to
corrosive products of combustion, but
have not operated, should be replaced
if they cannot be completely cleaned
by wiping the sprinkler with a cloth or
by brushing it with a soft bristle brush.
Care must be exercised to avoid dam-
age to the sprinklers — before, during,
and after installation. Sprinklers dam-
aged by dropping, striking, wrench
twist/slippage, or the like, must be re-
placed.Also,replaceanysprinklerthat
has a cracked bulb or that has lost
liquid from its bulb (ref. Installation
Section Note).
The owner is responsible for the in-
spection, testing, and maintenance of
their fire protection system and de-
vices in compliance with this docu-
ment, as well as with the applicable
standards of the National Fire Protec-
tion Association (e.g., NFPA 25), in
addition to the standards of any other
authorities having jurisdiction. The in-
stalling contractor or sprinkler manu-
facturer should be contacted relative
to any questions.
It is recommended that automatic
sprinkler systems be inspected,
tested, and maintained by a qualified
Inspection Service in accordance with
local requirements and/or national
code.
TFP344 Page 3 of 4
FIGURE 1
11.2 K-FACTOR SERIES ELO-231FRB
UPRIGHT - 3/4" NPT (TY5131) AND PENDENT - 3/4" NPT (TY5231) SPRINKLERS
1/2" (12,7 mm)
NOMINAL MAKE-IN
Temperature rating is indicated on deflector.
Pipe thread connections per ISO 7/1 can be
TYP.
2-13/16"
(71,4 mm)
UPRIGHT
TY5131
provided on special request.
**
*
PENDENT
TY5231
WRENCH
FLATS
RELIEF
THREAD
Deflector
Screw
Compression
Bulb
Components:
Seal
Cap
Frame
-
4
2
6
4
3
CROSS
SECTION
6
5
-
-
NPT**
3/4"
1
2
3
1-
-
-
*
Assembly
2-1/16"
(52,4 mm)
ESCUTCHEON
SEATING
SURFACE
5
FIGURE 2
W-TYPE 3 SPRINKLER
WRENCH
"FITTIN
G
SIDE"
FITTING
TOWARDS SPRINKLER
RECESS
WRENCH
(END "A")

Limited
Warranty
Products manufactured by Tyco Fire &
Building Products (TFBP) are war-
ranted solely to the original Buyer for
ten (10) years against defects in mate-
rial and workmanship when paid for
and properly installed and maintained
under normal use and service. This
warranty will expire ten (10) years
from date of shipment by TFBP. No
warranty is given for products or com-
ponents manufactured by companies
not affiliated by ownership with TFBP
or for products and components which
havebeensubjecttomisuse,improper
installation,corrosion, or which have
not been installed, maintained, modi-
fied or repaired in accordance with ap-
plicable Standards of the National Fire
Protection Association, and/or the
standards of any other Authorities
Having Jurisdiction. Materials found
by TFBP to be defective shall be either
repaired or replaced, at TFBP’s sole
option. TFBP neither assumes, nor
authorizesany persontoassumefor it,
any other obligation in connection with
the sale of products or parts of prod-
ucts.TFBPshallnot be responsiblefor
sprinkler system design errors or inac-
curate or incomplete information sup-
plied by Buyer or Buyer’s repre-
sentatives.
In no event shall TFBP be liable, in
contract, tort, strict liability or under
any other legal theory, for incidental,
indirect,specialorconsequentialdam-
ages, including but not limited to labor
charges, regardless of whether TFBP
was informed about the possibility of
such damages, and in no event shall
TFBP’s liability exceed an amount
equal to the sales price.
Theforegoingwarrantyismadeinlieu
of any and all other warranties, ex-
press or implied, including warranties
ofmerchantabilityandfitnessforapar-
ticular purpose.
This limited warranty sets forth the ex-
clusive remedy for claims based on
failure of or defect in products, materi-
als or components, whether the claim
is made in contract, tort, strict liability
or any other legal theory.
Ordering
Procedure
A Product Symbol Number (P/N) is not
specified when ordering sprinklers
with thread connections per ISO 7/1.
Contact your local distributor for avail-
ability.
Sprinkler Assemblies
with NPT Thread Connection:
Specify: (specify SIN), 11.2 K-factor,
(specify temperature rating), Series
ELO-231FRB Quick Response (spec-
ify Pendent or Upright) Sprinkler with
(specify finish), P/N (specify from Ta-
ble B).
Sprinkler Wrench:
Specify: W-Type 3 Sprinkler Wrench,
P/N 56-895-1-001.
Page4of4 TFP344
P/N 50 — XXX — X — XXX
155°F/68°C155
TEMPERATURE
RATING
500 9
SPRINKLER
TABLE B
PRODUCT SYMBOL NUMBER SELECTION
11.2 K-FACTOR SERIES ELO-231FRB
QUICK RESPONSE UPRIGHT AND PENDENT SPRINKLERS
UPRIGHT
3/4" NPT
(TY5131)
286
200°F/93°C200
286°F/141°C
CHROME PLATED
TYPE NATURAL BRASS1
502 PENDENT
3/4" NPT
(TY5231)
TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446