Tyco TY-FRL Series User manual

Page 1 of 4 AUGUST 2022 TFP280
Worldwide
Contacts
www.tyco-fire.com
IMPORTANT
Refer to Technical Data Sheet
TFP2300 for warnings pertaining to
regulatory and health information.
Always refer to Technical Data
Sheet TFP700 for the “INSTALLER
WARNING” that provides cautions
with respect to handling and instal-
lation of sprinkler systems and com-
ponents. Improper handling and
installation can permanently damage
a sprinkler system or its compo-
nents and cause the sprinkler to fail
to operate in a fire situation or cause
it to operate prematurely.
Scan the QR code or enter the URL
in a web browser to access the most
up-to-date electronic version of this
document. Data rates may apply.
docs.jci.com/tycore/tfp280
Series TY-FRL — 5.6 and 8.0 K-factor
Extended Coverage Horizontal Sidewall Sprinklers
Quick & Standard Response (Light Hazard)
General
Description
The Series TY-FRL, 5.6, and 8.0
K-factor, Extended Coverage Hori-
zontal Sidewall Sprinklers are solder
type spray sprinklers designed for use
in hydraulically calculated sprinkler
systems in light hazard, commercial
occupancies such as churches, res-
taurant seating areas, hotels, educa-
tional facilities, ofces, etc. With their
coverage up to 16 ft (4,9 m) wide by 24
ft (7,3 m) long, they are designed for
installation along a wall or the side of a
beam and just beneath a smooth, at,
horizontal ceiling. Horizontal sidewall
sprinklers are commonly used instead
of pendent or upright sprinklers due
to aesthetics or building construction
considerations where piping across the
ceiling is not desirable.
The fast response thermal sensitivity
rating of the Series TY-FRL provides for
a quick response extended coverage
(QREC) rating for many of the coverage
areas detailed in Table B and Table C.
NOTICE
The Series TY-FRL Sprinklers
described herein must be installed
and maintained in compliance with
this document, as well as with the
applicable standards of the National
Fire Protection Association, in addition
to the standards of any other authori-
ties having jurisdiction. Failure to do so
may impair the performance of these
devices.
The owner is responsible for main-
taining their fire protection system
and devices in proper operating con-
dition. Contact the installing contrac-
tor or product manufacturer with any
questions.
Sprinkler
Identication
Number
TY3322 — EC HSW, 5.6K, 1/2”NPT
TY4322 — EC HSW, 8.0K, 3/4”NPT
Note:
• TY3322 is a redesignation for S1888 and G8970.
• TY4322 is a redesignation for S1868 and G8170.
Technical
Data
Approvals
UL and C-UL Listed.
FM and NYC Approved.
Note: For complete approval information,
see Table A; and for information about
special design configurations, see the
Design Criteria Section.
Maximum Working Pressure
175 psi (12,1 bar)
Discharge Coefficient
K = 5.6 gpm/psi1/2 (80,6 Lpm/bar1/2)
K = 8.0 gpm/psi1/2 (115, 2 Lp m/ ba r1/2)
Temperature Ratings
See Table A
Finishes
Sprinkler: See Table A
Physical Characteristics
Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . .Bronze
Strut. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Monel
Deector . . . . . . . . . . . . . . . . . . . . . . . . . .Bronze
Hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Monel
Link Assembly. . . . . . . . . . . . . . . . . . . . . . Nickel
Ejection Spring . . . . . . . . . . . . . . . . . . . . Inconel
Button . . . . . . . . . . . . . . . . . . . . . . . . . . . .Bronze
Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TEFLON
Operation
The fusible link (heat collector) assem-
bly is comprised of two halves that
are joined together by a thin layer of
solder. When the rated temperature is
reached, the solder melts and the two
link halves separate, allowing the sprin-
kler to operate.
Design
Criteria
The Series TY-FRL Extended Cov-
erage Horizontal Sidewall Sprinklers
must be installed and utilized in light
hazard occupancies, under smooth,
at, horizontal ceilings as outlined in
the applicable installation standard rec-
ognized by the approval agency – for
example, UL recognizes NFPA 13, and

TFP280
Page 2 of 4
FM recognizes the FM Loss Prevention
data sheets. Installing the sprinklers in
recessed escutcheons voids all manu-
facturer’s warranties, as well as pos-
sibly voiding the sprinkler’s approvals
and/or listings.
Installation
The Series TY-FRL Sprinklers must
be installed in accordance with this
section.
NOTICE
A leak tight 1/2 in. NPT sprinkler joint
should be obtained by applying a min-
imum-to-maximum torque of 7 ft-lb to
14 ft-lb (9,5 to N·m 19,0 N·m). A leak
tight 3/4 in. NPT sprinkler joint should
be obtained by applying a minimum-to-
maximum torque of 10 ft-lb to 20 ft-lb
(13,4 N·m to 26,8 N·m). Higher levels of
torque may distort the sprinkler inlet
and cause leakage or impairment of the
sprinkler.
Do not attempt to make-up for insuf-
ficient adjustment in the escutcheon
plate by under- or over-tightening the
sprinkler. Readjust the position of the
sprinkler fitting to suit.
Step 1. The sprinklers must be installed
with their centerline of waterway paral-
lel to the ceiling and perpendicular to
the back wall surface. The word “TOP”
on the deector must face upwards
toward the ceiling.
Step 2. After installing an escutcheon
(as applicable) over the sprinkler pipe
threads and with pipe thread sealant
applied to the pipe threads, hand
tighten the sprinkler into the sprinkler
tting.
Step 3. Tighten the sprinkler into the
sprinkler tting using only the W-Type
9 Sprinkler Wrench as shown in Figure
3. Apply the wrench to the wrench area
as shown in Figure 1 or 2.
Care and
Maintenance
The Series TY-FRL Sprinklers must
be maintained and serviced in accor-
dance with this section.
Before closing a re protection system
main control valve for maintenance
work on the re protection system that
it controls, permission to shut down the
affected re protection system must be
obtained from the proper authorities
and all personnel who may be affected
by this action must be notied.
Absence of an escutcheon, which is
used to cover a clearance hole, may
delay the time to sprinkler operation in
a re situation.
-
3
Deflector
Temperature rating is indicated on Deflector.
Seal
Ejection
Button
Link
Hook
-
8
-
5
6
-
4
-
Strut
2
-
Pipe thread connections per ISO 7-1 can be provided on special request.
1
-Frame
7
-
Assembly
Spring
WATERWAY
OF SPRINKLER
CENTERLINE
SURFACE
PLATE SEATING
WALL
DEFLECTOR
(14,3 mm)
9/16"
NOMINAL
7/16" (11,1 mm)
DEFLECTOR
BOSS
(38,1 mm)
1-1/2"
2-13/16"
(71,4 mm)
1/2" (12,7 mm)
NOMINAL MAKE-IN
(54,0 mm)
2-1/8"
AREA
WRENCH
WRENCH
FLANGES
8
6
*
TOP
34527
NPT
3/4"
1
**
*
*
**
-
3
Deflector
Temperature rating is indicated on Deflector.
Seal
Ejection
Button
Link
Hook
-
8
-
5
6
-
4
-
Strut
2
-
Pipe thread connections per ISO 7-1 can be provided on special request.
1
-Frame
7
-
Assembly
Spring
WALL
PLATE SEATING
SURFACE
CENTERLINE
OF SPRINKLER
WATERWAY
DEFLECTOR
(14,3 mm)
9/16"
DEFLECTOR
7/16" (11,1 mm)
NOMINAL
BOSS
(38,1 mm)
1-1/2"
(71,4 mm)
2-13/16"
2-1/8"
(54,0 mm)
NOMINAL MAKE-IN
7/16" (11,1 mm)
WRENCH
AREA
8
FLANGES
WRENCH
6
*
TOP
34527
1/2"
NPT
1
**
*
*
**
FIGURE 1
SERIES TY-FRL (TY3322) EXTENDED COVERAGE
HORIZONTAL SIDEWALL SPRINKLERS
5.6 K-FACTOR, 1/2 INCH NPT
FIGURE 2
SERIES TY-FRL (TY4322) EXTENDED COVERAGE
HORIZONTAL SIDEWALL SPRINKLERS
8.0 K-FACTOR, 3/4 INCH NPT

TFP280
Page 3 of 4
NOTES
1. Backwall (where sprinkler is located) by sidewall (length of throw).
2. Requirement is based on minimum ow in GPM from each sprinkler. The indicted residual pressures are based on the nominal K-factor.
3. The centerline of the sprinkler waterway is located 7/16 inch (11,1 mm) below the deector (Ref. Figures 1 and 2).
4. Minimum spacing is for lateral distance between sprinklers located along a single wall. Otherwise adjacent sprinklers (i.e., sidewall sprinklers on an adjacent wall, on an opposite
wall, or pendent sprinklers) must be located outside of the maximum listed protection area of the extended coverage sidewall sprinkler being utilized.
5.6 K EXTENDED COVERAGE HORIZONTAL SIDEWALL SPRINKLER (TY3322)
Response
Rating Coverage Area (1),
Ft x Ft (m x m)
Minimum
Flow(2),
GPM (LPM)
Minimum
Pressure(2),
PSI (BAR)
Deflector-
To-Ceiling
Distance (3), In. (mm)
Sprinkler
Temperature
Rating, °F
Minimum
Spacing (4),
Ft. (m)
Quick 16 x 16 (4,9 x 4,9) 29 (110) 26.8 (1,85) 4 to 12 (100 to 300) 165 8 (2,4)
Quick 16 x 20 (4,9 x 6,1) 33 (125) 34.7 (2,39) 4 to 12 (100 to 300) 165 8 (2,4)
Quick 18 x 16 (5,5 x 4,9) 29 (110) 26.8 (1,85) 4 to 12 (100 to 300) 165 8 (2,4)
8.0 K EXTENDED COVERAGE HORIZONTAL SIDEWALL SPRINKLER (TY4322)
Response
Rating Coverage Area (1),
Ft x Ft (m x m)
Minimum
Flow(2),
GPM (LPM)
Minimum
Pressure(2),
PSI (BAR)
Deflector-
To-Ceiling
Distance (3), In. (mm)
Sprinkler
Temperature
Rating, °F
Minimum
Spacing (4),
Ft. (m)
Quick 16 x 16 (4,9 x 4,9) 26 (98) 10.6 (0,73) 4 to 6 (100 to 150) 165 10 (3,1)
Quick 16 x 18 (4,9 x 5,5) 29 (110) 13.1 (0,90) 4 to 6 (100 to 150) 165 10 (3,1)
Quick 16 x 18 (4,9 x 5,5) 38 (144) 22.6 (1,56) 4 to 18 (100 to 450) 165 10 (3,1)
Quick 16 x 20 (4,9 x 6,1) 34 (129) 18.1 (1, 25) 4 to 6 (100 to 150) 165 10 (3,1)
Quick 16 x 22 (4,9 x 6,7) 37 (140) 21.4 (1,48) 4 to 6 (100 to 150) 165 10 (3,1)
Quick 18 x 16 (5,5 x 4,9) 31 (117 ) 15.0 (1,03) 4 to 6 (100 to 150) 165 10 (3,1)
Quick 18 x 18 (5,5 x 5,5) 33 (125) 17.0 (1,17) 4 to 6 (100 to 150) 165 10 (3,1)
Quick 20 x 16 (6,1 x 4,9) 35 (133) 19.1 (1,32) 4 to 6 (100 to 150) 165 10 (3,1)
Standard 16 x 20 (4,9 x 6,1) 45 (170) 31.6 (2,18) 4 to 18 (100 to 450) 165 10 (3,1)
Standard 16 x 22 (4,9 x 6,7) 37 (140) 21.4 (1,48) 4 to 6 (100 to 150) 165 10 (3,1)
Standard 16 x 24 (4,9 x 7,3) 44 (167) 30.3 (2,09) 4 to 6 (100 to 150) 165 10 (3,1)
K-factor Type Temperature
Rating
Frame
Color
Code
Sprinkler Finish
Natural
Brass Chrome Plated
5.6
1/2 in.
NPT
EC HSW
(TY3322) 165ºF/ 74ºC Unpainted 1, 2, 3, 4
8.0
3/4 in.
NPT
EC HSW
( T Y43 22) 165º F/74ºC Unpainted 1, 2, 3, 4
NOTES:
1. Listed by Underwriters Laboratories, Inc. (UL) per Table B.
2. Listed by Underwriters Laboratories, Inc. for use in Canada per Table B.
3. Approved by Factory Mutual Research Corporation (FM) per Table C.
4. Approved by the City of New York under MEA 112-04-E.
RECESS
WRENCH
FIGURE 3
W-TYPE 9 SPRINKLER
WRENCH
TABLE B
UL AND C-UL LISTING COVERAGE AND FLOW RATE CRITERIA
TABLE A
LABORATORY LISTINGS AND APPROVALS
(REFER TO THE DESIGN CRITERIA SECTION)

TFP280
Page 4 of 4
NATIONAL FIRE PROTECTION ASSOCIATION and NFPA are registered trademarks of National Fire Protection Association;
TEFLON is a trademark of The Chemours Company FC, LLC
1467 Elmwood Avenue, Cranston, RI 02910 | Telephone [phone]
© 2022 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision date and are subject to change without notice.
Sprinklers that are found to be leaking
or exhibiting visible signs of corrosion
must be replaced.
Automatic sprinklers must never be
painted, plated, coated or otherwise
altered after leaving the factory. Modi-
ed or over-heated sprinklers must be
replaced.
Care must be exercised to avoid
damage to the sprinklers -before,
during, and after installation. Sprin-
klers damaged by dropping, striking,
wrench twist/slippage, or the like, must
be replaced.
The owner is responsible for the
inspection, testing, and maintenance of
their re protection system and devices
in compliance with this document, as
well as with the applicable standards
of the National Fire Protection Associ-
ation such as NFPA 25, in addition to
the standards of any other authorities
having jurisdiction. Contact the install-
ing contractor or product manufacturer
with any questions.
It is recommended that automatic
sprinkler systems be inspected, tested,
and maintained by a qualied Inspec-
tion Service in accordance with local
requirements and/or national code.
Limited
Warranty
For warranty terms and conditions, visit
www.tyco-re.com.
Ordering
Procedure
Contact your local distributor for avail-
ability. When placing an order, indicate
the full product name and part number
(P/N).
Sprinkler Assemblies with NPT
Thread Connections
Specify: (Specify Model/SIN), (specify
K-factor), Series TY-FRL Extended
Coverage Horizontal Sidewall Sprin-
kler with (specify nish), P/N (specify
from Table D)
Sprinkler Wrench
Specify: W-Type 9 Sprinkler Wrench,
P/N 56-000-1-849
5.6 K EXTENDED COVERAGE HORIZONTAL SIDEWALL SPRINKLER (TY3322)
Response
Rating Coverage Area (1),
ft x ft (m x m)
Minimum
Flow(2),
gpm (Lpm)
Minimum
Pressure(2),
psi (bar)
Deflector-
To-Ceiling
Distance (3), in. (mm)
Sprinkler
Temperature
Rating, °F
Minimum
Spacing (4),
ft. (m)
Quick 16 x 16 (4,9 x 4,9) 26 (98) 22 (1,51) 4 to 12 (100 to 300) 165 8 (2,4)
Quick 16 x 18 (4,9 x 5,5) 30 (114) 29 (2,00) 4 to 12 (100 to 300) 165 8 (2,4)
Quick 16 x 20 (4,9 x 6,1) 33 (125) 35 (2,41) 4 to 12 (100 to 300) 165 8 (2,4)
8.0 K EXTENDED COVERAGE HORIZONTAL SIDEWALL SPRINKLER (TY4322)
Response
Rating Coverage Area (1),
ft x ft (m x m)
Minimum
Flow(2),
gpm (Lpm)
Minimum
Pressure(2),
psi (bar)
Deflector-
To-Ceiling
Distance (3), in. (mm)
Sprinkler
Temperature
Rating, °F
Minimum
Spacing (4),
ft. (m)
Quick 16 x 16 (4,9 x 4,9) 32 (121) 16 (1,10) 4 to 12 (100 to 300) 165 10 (3,1)
Quick 16 x 18 (4,9 x 5,5) 36 (136) 20 (1,38) 4 to 12 (100 to 300) 165 10 (3,1)
Quick 16 x 20 (4,9 x 6,1) 40 (151) 25 (1,72) 4 to 12 (100 to 300) 165 10 (3,1)
Quick 16 x 22 (4,9 x 6,7) 44 (167) 30 (2,06) 4 to 12 (100 to 300) 165 10 (3,1)
Quick 16 x 24 (4,9 x 7,3) 48 (182) 36 (2,48) 4 to 12 (100 to 300) 165 10 (3,1)
NOTES
1. Backwall (where sprinkler is located) by sidewall (length of throw).
2. Requirement is based on maintaining both minimum ow and minimum residual pressure.
3. The centerline of the sprinkler waterway is located 7/16 inch (11,1 mm) below the deector (Ref. Figures 1 and 2).
4. Minimum spacing is for lateral distance between sprinklers located along a single wall. Otherwise adjacent sprinklers (i.e., sidewall sprinklers on an adjacent wall, on an
opposite wall, or pendent sprinklers) must be located outside of the maximum listed protection area of the extended coverage sidewall sprinkler being utilized.
TABLE C
FM COVERAGE AND FLOW RATE CRITERIA
58—XXX—X—165
Model/SIN
970 5.6K EC HSW TY3322
170 8.0K EC HSW T Y4 322
Sprinkler Finish
1NATURAL BRASS
9CHROME PLATED
TABLE D
PART NUMBER SELECTION
SERIES TY-FRL EXTENDED COVERAGE HORIZONTAL SIDEWALL SPRINKLERS

TFP280
Change History Appendix
Worldwide
Contacts
www.tyco-fire.com
1467 Elmwood Avenue, Cranston, RI 02910 | Telephone [phone]
© 2022 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision date and are subject to change without notice.
ISSUE DATE NOTES
08-22
Reduced document to 4 pages, formerly 6 pageS; Page 1, added QR code and URL to allow convenient
access to electronic version from printed document; Page 4, changed corporate address and telephone
number to 1467 Elmwood Avenue, Cranston, RI 02910 | Telephone [phone], formerly 1400 Pen-
nbrook Parkway, Lansdale, PA 19446 | Telephone [phone].
08-18
Updated Tyco® branding and document format; Added Johnson Controls copyright; Added disclaimer
stating specications and information subject to change without notice; Added reference to Regulatory
and Health Warning Technical Data Sheet TFP2300.
02-17 Updated limited warranty information.
03-09 Removed 140°F (60°C) temperatutre rating.
01-05 Added reference to Installer Warning data sheet TFP700; Added NYC Approved.
12-02 Table B, 18x16, 18x18, and 20x16 coverage areas; corrected typographical errors.
11- 02 New Technical Data Sheet TFP280 describes Series TY-FRL Extended Coverage Horizonatal Sidewall
Sprinklers.