Ubiquiti EdgeRouter ER-10X User manual

10. 10. 2019 ER-10X Quick Start Guide
https://dl.ubnt.com/qsg/ER-10X/ER-10X_EN.html 1/22
EdgeRouter ER-10X Wall Mount Screws (Qty. 2) Wall Mount Anchors (Qty. 2)
Ground Screw Ground Screw Cable Clip
Package Contents
Installation Requirements
Wall-mounting (optional)
Drill with 6 mm drill bit
Phillips screwdriver
ER-10X Quick Start Guide

10. 10. 2019 ER-10X Quick Start Guide
https://dl.ubnt.com/qsg/ER-10X/ER-10X_EN.html 2/22
For indoor applications, use Category 5 (or above) UTP cabling approved for indoor
use.
For outdoor applications, shielded Category 5 (or above) cabling should be used for
all wired Ethernet connections and should be grounded through the AC ground of the
power supply.
We recommend that you protect your networks from harmful outdoor environments
and destructive ESD events with industrial-grade, shielded Ethernet cable from
Ubiquiti. For more details, visit: ui.com/toughcable
Note: Although the cabling can be located outdoors, the EdgeRouter itself
should be housed inside a protective enclosure.
Hardware Overview
ER-10X Quick Start Guide

10. 10. 2019 ER-10X Quick Start Guide
https://dl.ubnt.com/qsg/ER-10X/ER-10X_EN.html 3/22
System LED
RJ45 PoE LED (Port 0)
Flashing White Bootup in Progress
White
Ready for Use
Not Connected to Ubiquiti® Network Management
System (UNMS™)
Blue
Ready for Use
Connected to UNMS
Steady Blue with
Occasional Flashing
Ready for Use
Unable to Connect to UNMS
Quickly Flashing Blue Used to Locate a Device in UNMS
Alternating Blue/White Firmware Upgrade in Progress
ER-10X Quick Start Guide

10. 10. 2019 ER-10X Quick Start Guide
https://dl.ubnt.com/qsg/ER-10X/ER-10X_EN.html 4/22
RJ45 Speed/Link/Activity LED (Ports 0 - 9)
RJ45 PoE LED (Port 9)
Console
USB
RJ45 (Ports 0 - 9)
Off No PoE
Green 24V Passive PoE Input
Off No Link
Green
Link Established
Flashing Indicates Activity
Off No PoE
Green 24V 2-Pair Passive PoE Output
RJ45 serial console port for Command Line Interface (CLI) management.
Reserved for future use.
All RJ45 ports can be used for routing and support 10/100/1000 Mbps Ethernet
connections. Ports 0 - 9 can be configured for switching functions using the
EdgeOS® Configuration Interface.
PoE In (Port 0) Supports 24V Passive PoE input.
PoE Out (Port 9) Supports optional 24V Passive PoE passthrough (disabled by
default).
ER-10X Quick Start Guide

10. 10. 2019 ER-10X Quick Start Guide
https://dl.ubnt.com/qsg/ER-10X/ER-10X_EN.html 5/22
Reset Button
Power
Grounding Point
Click here to learn how to reset an EdgeRouter to factory defaults.
Connect the included Power Adapter to the Power port.
Ground bonding point for an optional ground wire.
Hardware Installation
Wall Mounting
1.
ER-10X Quick Start Guide

10. 10. 2019 ER-10X Quick Start Guide
https://dl.ubnt.com/qsg/ER-10X/ER-10X_EN.html 6/22
2.
ER-10X Quick Start Guide

10. 10. 2019 ER-10X Quick Start Guide
https://dl.ubnt.com/qsg/ER-10X/ER-10X_EN.html 7/22
3.
ER-10X Quick Start Guide

10. 10. 2019 ER-10X Quick Start Guide
https://dl.ubnt.com/qsg/ER-10X/ER-10X_EN.html 8/22
4.
ER-10X Quick Start Guide

10. 10. 2019 ER-10X Quick Start Guide
https://dl.ubnt.com/qsg/ER-10X/ER-10X_EN.html 9/22
Grounding the EdgeRouter (Recommended)
The Power Adapter grounds the device; however, you can add optional ESD grounding
for enhanced ESD protection (ground wire not included).
ER-10X Quick Start Guide

10. 10. 2019 ER-10X Quick Start Guide
https://dl.ubnt.com/qsg/ER-10X/ER-10X_EN.html 10/22
Optional
ER-10X Quick Start Guide