Ubiquiti NanoStationM Series User manual

NanoStation M2/M3/M365/M5 Zip Tie PoE (24V, 0.5A) with Mounting
Bracket
Power Cord
NanoStationloco M2/M5 Zip Tie PoE (24V, 0.5A) with Mounting
Bracket
Package Contents
NSM2/NSM3/NSM365/NSM5
locoM2/locoM5
NanoStationM/locoM Series Quick Start Guide

Power Cord
NanoStationlocoM9 Zip Tie PoE (24V, 0.5A) with Mounting
Bracket
Power Cord
locoM9
Installation Requirements
Shielded Category 5 (or above) cabling with drain wire should be used for all wired
Ethernet connections and should be grounded through the AC ground of the PoE.
We recommend that you protect your networks from harmful outdoor
environments and destructive ESD events with industrial-grade, shielded Ethernet
cable from Ubiquiti. For more details, visit ui.com/toughcable
Surge protection should be used for all outdoor installations. We recommend that
you use two Ethernet Surge Protectors, model ETH-SP, one near the NanoStation
and the other at the entry point to the building. The ETH-SP will absorb power
surges and safely discharge them into the ground.
NanoStationM/locoM Series Quick Start Guide

Hardware Overview
NSM2/NSM3/NSM365/NSM5/locoM2/locoM5
NanoStationM/locoM Series Quick Start Guide

Power LED
The LED will light green when the device is connected to a power source.
NanoStationM/locoM Series Quick Start Guide

LAN1 LED
LAN2 LED
Signal LEDs
Secondary Port
Main/LAN* Port
Reset Button
The LED will light steady green when an active Ethernet connection is made to
the Main/LAN port and flash when there is activity.
(NanoStation M2/M3/M5 only) The LED will light steady green when an active
Ethernet connection is made to the Secondary port and flash when there is
activity.
In airOS®, you can modify the threshold values for the wireless signal strength
LEDs on the Advanced tab under Signal LED Thresholds. The default values are
shown below:
(NanoStationM2/M3/M5 only) This 10/100 Ethernet port is used for bridging and
supports software-configurable PoE passthrough.
Note: To use PoE passthrough on the Secondary port, a 24V, 1A PoE
adapter is required.
This 10/100 Ethernet port is used to connect the power and should be
connected to the LAN and DHCP server.
To reset to factory defaults, press and hold the Reset button for more than 10
seconds while the device is powered on. Alternatively, the device may be reset
remotely via a Reset button located on the bottom of the PoE adapter.
* The Main port is labeled LAN on the NanoStationlocoM2/M5.
locoM9
NanoStationM/locoM Series Quick Start Guide

Power LED
LAN1 LED
Signal LEDs
The LED will light green when the device is connected to a power source.
The LED will light steady green when an active Ethernet connection is made to
the Main/LAN port and flash when there is activity.
In airOS®, you can modify the threshold values for the wireless signal strength
LEDs on the Advanced tab under Signal LED Thresholds. The default values are
shown below:
NanoStationM/locoM Series Quick Start Guide

RP-SMA Antenna Connector
Main/LAN Port
Reset Button
Reserved for future use.
This 10/100 Ethernet port is used to connect the power and should be
connected to the LAN and DHCP server.
To reset to factory defaults, press and hold the Reset button for more than 10
seconds while the device is powered on. Alternatively, the device may be reset
remotely via a Reset button located on the bottom of the PoE adapter.
Installation
1.
2.
NanoStationM/locoM Series Quick Start Guide

3.
4.
NanoStationM/locoM Series Quick Start Guide

5.
NanoStationM/locoM Series Quick Start Guide

6.
NanoStationM/locoM Series Quick Start Guide