Ubiquiti UF-Nano User manual

19.02.2020 UF-Nano Quck Start Gude
https://dl.ubnt.com/qsg/UF-Nano/UF-Nano_EN.html 1/14
Nano G Wall Mount Bracket Screws (Qty. 4)
Screw Anchors (Qty. 4) G  gab  t PoE (24V, 0.3A) w  th
Mount Bracket Power Cord
Package Contents
System Requ  rements
L  nux, Mac OS X, or M  crosoft W  ndows 7/8/10
Web Browser: Google Chrome (Other browsers may have l  m  ted funct  onal  ty)
Before You Beg  n
Des  gn  ng your f  rst GPON deployment requ  res spec  f  c knowledge and plann  ng. For
 nformat  on on GPON network des  gn and  nstallat  on,  nclud  ng  mportant
cons  derat  ons and best pract  ces, refer to:
ubnt.l  nk/UF  ber-GPON-Gett  ng-Started
ubnt.l  nk/Des  gn  ng-a-GPON-Network
For deta  ls on conf  gur  ng UF  ber dev  ces for the f  rst t  me to allow ONU LAN ports to
prov  de connect  v  ty, refer to: ubnt.l  nk/UF  ber-In  t  al-Conf  gurat  on
Hardware Overv  ew
UF-Nano Qu  ck Start Gu  de
All manuals and user guides at all-guides.com
all-guides.com

19.02.2020 UF-Nano Quck Start Gude
https://dl.ubnt.com/qsg/UF-Nano/UF-Nano_EN.html 2/14
PON Port
Reset Button
Ethernet Port
GPON LED
SC/APC GPON port supports WAN connect  ons of 2.488 Gbps downstream and
1.244 Gbps upstream.
Press and release the Reset button to restore the dev  ce to factory default sett  ngs.
RJ45 Ethernet LAN port supports 10/100/1000 Mbps connect  ons and pass  ve PoE to
power the dev  ce.
Green GPON connected and dev
 ce  s  ntegrated  nto a
network and work  ng properly
Red No GPON connect
 on. Error code  s shown on the
D  g  tal D  splay.
UF-Nano Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

19.02.2020 UF-Nano Quck Start Gude
https://dl.ubnt.com/qsg/UF-Nano/UF-Nano_EN.html 3/14
Power LED
Ethernet LED
D  g  tal D  splay
Flash  ng Red Dev  ce  s d  scovered by OLT and wa  t  ng to be
 ntegrated
Off No power, dev  ce  s off
Wh  te Power on, dev  ce  s on
Off No Ethernet connect  on
Green Ethernet  s connected
Flash  ng Ethernet act  v  ty
The D  g  tal D  splay shows dev  ce status and RX/TX deta  ls of the PON connect  on.
The D  g  tal D  splay  s also a phys  cal button. Press the d  splay to cycle through the
 nformat  on.
Mbps D  splays the act  ve download (RX) and upload (TX) speeds of the PON
connect  on.
dBm D  splays the RX and TX power of the PON connect  on.
Note: If the GPON LED l  ghts red, a malfunct  on or error w  th the PON
connect  on ex  sts. Check and test the f  ber opt  c cable to ensure proper
operat  on.
IP D  splays the PON (LAN) IP address.
UF-Nano Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

19.02.2020 UF-Nano Quck Start Gude
https://dl.ubnt.com/qsg/UF-Nano/UF-Nano_EN.html 4/14
Hardware Installat  on
Wall Mount  ng
1.
2.
UF-Nano Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

19.02.2020 UF-Nano Quck Start Gude
https://dl.ubnt.com/qsg/UF-Nano/UF-Nano_EN.html 5/14
3.
UF-Nano Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

19.02.2020 UF-Nano Quck Start Gude
https://dl.ubnt.com/qsg/UF-Nano/UF-Nano_EN.html 6/14
4.
UF-Nano Qu  ck Start Gu  de
All manuals and user guides at all-guides.com
all-guides.com

19.02.2020 UF-Nano Quck Start Gude
https://dl.ubnt.com/qsg/UF-Nano/UF-Nano_EN.html 7/14
Connect  ng F  ber
WARNING: Never look d  rectly  nto the ends of f  ber or modules. The em  tted
l  ght could cause damage to the eye.
WARNING: Unt  l ready for use, keep modules and f  ber patch cables covered
us  ng the  ncluded protect  ve caps to ensure the connect  ons stay clean.
WARNING: DO NOT connect the dev  ce d  rectly to a UF  ber GPON module (UF-
GP-B+ or UF-GP-C+). Do  ng so w  ll damage the dev  ce opt  cs. Ensure that the
dev  ce’s rece  ved s  gnal level never exceeds -8 dBm. Use a UF  ber PLC Spl  tter to
add attenuat  on as needed.
UF-Nano Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

19.02.2020 UF-Nano Quck Start Gude
https://dl.ubnt.com/qsg/UF-Nano/UF-Nano_EN.html 8/14
Connect  ng Power
1.
2. 
WARNING: The sw  tch port must comply w  th the power spec  f  cat  ons
l  sted  n th  s Qu  ck Start Gu  de.
UF-Nano Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

19.02.2020 UF-Nano Quck Start Gude
https://dl.ubnt.com/qsg/UF-Nano/UF-Nano_EN.html 9/14
OR
Opt  onal
Access  ng the Conf  gurat  on Interface
1. Ensure that your computer (or other host system)  s connected to the dev  ce.
2. Conf  gure the Ethernet adapter on your host system w  th a stat  c IP address on the
192.168.1.x subnet.
3. Launch your web browser. Type http://192.168.1.1  n the address f  eld. Press enter
(PC) or return (Mac).
4. Enter ubnt  n the Username and Password f  elds. Cl  ck Log  n.
UF-Nano Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

19.02.2020 UF-Nano Quck Start Gude
https://dl.ubnt.com/qsg/UF-Nano/UF-Nano_EN.html 10/14
Custom  ze sett  ngs as needed. For more  nformat  on, refer to the UF  ber resources,
wh  ch are ava  lable at: ubnt.l  nk/UF  ber-Support
OLT Compat  b  l  ty Prof  les
The dev  ce  s compat  ble w  th most major brands of OLT (Opt  cal L  ne Term  nals) and
offers three compat  b  l  ty prof  les. By default, the dev  ce  s set to Prof  le 1 - Ub  qu  t 
UF  ber OLT. For other brands, manually select Prof  le 2 or 3.
Note: For more  nformat  on, v  s  t ubnt.l  nk/Supported-3rd-Party-OLTs
1.
2.
UF-Nano Qu  ck Start Gu  de
All manuals and user guides at all-guides.com