Uplift Desk 2-Leg Side Table Quick setup guide

DIRECTIONS FOR ASSEMBLY AND USE
2-Leg Side Table
®
SAVE THESE INSTRUCTIONS:
Any user or installer of the table must study this manual carefully. If this table is sold,
please provide the manual to the buyer, installers, or support personnel using the product.
TABLE OF CONTENTS PAGE
1 Safety and Warnings 2
2 Usage 2
3 Parts List 2
4 Assembly Instructions 4
5 Placement 5
6 TechnicalSpecications 5
FRM020/R01
4933053179446 - THS610

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
2
This table is designed for use in dry work areas only. These tables are designed only for the purposes
included in this manual. They should not be used in environments with high humidity or dampness.
Any other use is at user’s risk.
Do not sit or stand on the table frame.
Children should never use the table unless they are supervised by adults.
Liability: Under no circumstances does the manufacturer accept warranty claims or liability claims for
damages caused from improper use or handling of the table frame other than that which is described
in this operation manual.
When using an electrical furnishing, basic precautions should always be followed, including the following:
Read all instructions before using the table.
FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY, AND OPERATION INSTRUCTIONS
AND WARNINGS REGARDING THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS PROPERTY
DAMAGE OR BODILY INJURY.
WARNING - To reduce the risk of injury to persons, or property damage:
• Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled
persons.
• Use this table only for its intended use as described in these instructions. Do not use attachments
not recommended by the manufacturer.
• Do not use outdoors.
• Inappropriate use of this product may cause property or bodily injury.
• Please provide this manual to any users, installers, or support personnel using the product.
•
If casters are not installed, use a two-person lift and lift the table so that it can be moved without
dragging. Dragging the table may cause the frame and screws to pull loose from the desktop.
• Maximum weight capacity of this product is 355 Ib. Do not overload your table.
2. USAGE
1. SAFETY AND WARNINGS
Foot
(qty 2)
Leg
(qty 2)
Adhesive pads
(qty 10)
Leveling stud
(pre-installed, qty 4)
M6x10
Machine screw
(qty 8)
#10x5/8’’
Wood screw
(qty 12)
#10-24x5/8’’
Machine screw
(qty 8)
Crossbar end
(qty 2)
Crossbar rail
(qty 2)
Side bracket
(qty 2)
M6x14
Machine screw
(qty 24)
Philips Head Screwdriver
and/or Power Drill
Tape Measure
Allen wrench
(included)
Tools requiredComponents
1234
5678
910 10
a b
3. PARTS LIST

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com 3
Part Description Qty
Leg 2
Foot 2
Crossbar end 2
Crossbar rail 2
Side bracket 2
Adhesive pads 10
Leveling studs (pre-installed in feet) 4
M6x14 Machine screw 24
M6x10 Machine screw 8
#10x5/8’’ Wood screw (not pictured) 12
#10-24x5/8’’ Machine screw (not pictured) 8
Please count all pieces before disposing of any carton or packing material. Use a padded or carpeted
area for assembly to avoid damage. For ease and safety, we recommend two people for assembly.
1
1
2
2
3
4
5
5
6
7
7
8
8
8
8
8
8
8
8
8
9
10
10
a
b
Conguration
6
9
B. Position the Crossbar ends (part 3) on their sides. You will be inserting
the Legs (part 1) into the Crossbar ends from below. When positioned correctly,
themounttabswillbefacingup(g.1).
Now, place the Legs (part 1) into the Crossbar ends from the
bottom(g.2).UsingthesuppliedAllenwrench,insertfour
(4) M6x14 Machine screws (part 12) into the Crossbar ends,
and rotate each screw only a few turns. Do not tighten fully
until step D.
If you drop a screw inside the Crossbar end, simply tilt
to retrieve the screw.
A. FullyseparatetheCrossbarends(part3)youwillndtheCrossbarrails(parts4)inside.
g.1
g.2
3 3
4
12
12
4. ASSEMBLY INSTRUCTIONS

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
4
C. Take the two Side brackets (part 5) and attach them to the Leg
assemblies, using four (4) M6x14 Machine screws (part 12) each. Use
the Allen wrench, and rotate each screw only a few turns. Do not
tighten fully until step D.
If you are having trouble getting all the screws started, it is because
other screws are too tight. You’ll need to back out some screws in
order to loosen the tolerance of the screw holes.
D. Once all of the parts are connected, you can now tighten the eight (8) Screws from Step B and the
eight (8) Screws from Step C (16 screws in total).
E. Remove backing from the Adhesive pads (part 6) and position
along the assembly as shown. Be sure to not cover any of the holes.
F. Slide Crossbar rails (part 4) back into Crossbar ends (part 3).
Ensure the slots of the Crossbar rails are facing inward. The slot on
theCrossbarrailisoffset;itwillneedtobealignedinaspecicway
totaroundtheMachinescrews.MakesurethattheCrossbarrail
(part 4) can slide all the way to the end of the Crossbar end (part 3).
Ifitdoesn’tt,taketheCrossbarrailoutandipitover,withtheslots
facinginwardandnearthetopoftheedge,furtherfromtheoor. 3
3
3
4
12
5
6
G. Attach each Foot (part 2) with four (4)
M6x14 Machine screws (part 12) and tighten
bolts in a cross pattern.
Be sure to point the long end of the Foot in
the same direction as the long end of the Side
bracket. 11
2
2
12
H. Your desktop may be pre-drilled or include threaded inserts.
Please check both sides of the desktop for holes before placing
the table frame! If there are holes, carefully line up the frame to
match the holes on the underside of the desktop.
Adjustthewidthofthebasetotthedesktopbyslidingthetwo
halves outward. (33’’ max between the inside edge of Crossbar
ends)
If your desktop is not pre-drilled & does not include threaded in-
serts, place the base where you want it. We recommend leaving at
least 1/2” of desktop width on either side of the Side brackets.
The table feet are deeper than the Side brackets. If your top is
25.5”-27.5” deep and you want the rear edge of the top in line with
the rear edges of the feet, offset your desktop toward the back.
If you are using your own desktop, please note that the Minimum desktop size is 43’’ wide x 24’’ deep.
Theframewillnottonanydesktopsmallerthanthis.

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com 5
13
I. Secure the Center rails at both ends using
eight (8) M6x10 Machine screws (part 13), four
(4) per side. Ensure all eight (8) Machine screws
hit the metal Crossbar rails to prevent them
from sliding.
Double-check that the frame is properly positioned
on the underside of the desktop.
Attach the frame assembly to the underside of the
desktop using eight (8) of the screws that you have chosen.
J. Choose the screw to fasten your frame to your desktop.
If your desktop does not have metal threaded inserts,
use the #10x5/8’’ Wood screws (part 14-a)
If your desktop does have metal threaded inserts,
use the #10-24x5/8’’ Machine screws (part 14-b)
3 per Side bracket 6 total
1 per Crossbar end 2 total
a
b
14
14
N. Turn the assembled table right-side up. With two people, grab the table by the frame and desktop
equally, and turn the table right-side up. Adjust the Leveling studs (part 9) on the Feet (part 2) as needed.
Copyright Notice: This guide is a component of the UPLIFT Desk ™ . This guide is a part of the scope of delivery, even if the item is resold. This guide is also available on the UPLIFT
Desk website: upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other published form without the prior written consent of UPLIFT Desk.
These instructions are subject to United States copyright law.
©
Following table assembly, adjust the Leveling studs or casters (sold separately) on the feet so that the
table is level and does not shift its position.
When moving the table, if casters are not installed, use a two-person lift and lift the table so that it can be
moved without dragging. Dragging the table may cause the frame and screws to pull loose from the desktop.
When moving the table, DO NOT lift the table by the desktop alone, or the frame, alone. Support both the
frame and the desktop equally. Favoring one over the other can stress the fasteners connecting the table
frame to the desktop. Lower the table completely and lift the table by grasping the frame.
5. PLACEMENT
Height 28” (without desktop)
Width Range 42.125” min - 74.75” max
Weight Capacity 355 lbs
6. TECHNICAL SPECIFICATIONS

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
Notes

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
Notes

®
1-800-349-3839
[email protected]
www.upliftdesk.com