Uplift Desk FRM401 User manual

For assembly assistance,
visit upliftdesk.com/FRM401
call 800-349-3839 or email [email protected]
355 lb
two person
assembly
Patent Pending, ©2018 UPLIFT Desk®. All Rights Reserved
4-Leg Seated Height
Side Table Frame
®

Thank you for choosing UPLIFT Desk.

3© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com
SAFETY AND WARNINGS
Count all pieces before disposing of any carton or packing material. Use a padded or carpeted area
for assembly to avoid damage. For ease and safety, we recommend two people for assembly.
355 lb
355 lb
You’ll need:
tape measure,
and phillips-head
screwdriver
COMPONENTS
PACKAGE CONTENTS
Leg assembly
(qty 2)
Crossbar rail
(qty 2)
Crossbar end
(qty 2)
WARNING: Designed for use in dry work environments only. Use only indoors.
Please read this manual carefully. Inappropriate use of this table can cause property damage or bodily injury.
Under no circumstances does the manufacturer accept warranty or liability claims for damages caused from
improper use or handling of this table. Provide this manual to any new user.
CONFIGURATION
C1
C1
C3
C2
C2
H1
H1
H1
H1 H1
C3C2C1
HARDWARE
M8x8 Set screw
(qty 16)
#10-24x3/4’’
Screw
(qty 8)
#10-3/4’’
Screw
(qty 8)
Washer
(qty 8)
Allen wrench
H1 H3 H4
C3 C4 C5
C9
H4a
H7
C6
H1 H2 H3 H5
H4b
H6
C7
C3 C4 C5
C9
H4a
H7
C6
H1 H2 H3 H5
H4b
H6
C7
C3 C4 C5
C9
H4a
H7
C6
H1 H2 H3 H5
H4b
H6
C7
C3 C4 C5
C9
H4a
H7
C6
H1 H2 H3 H5
H4b
H6
C7
C3 C4 C5
C9
H4a
H7
C6
H1 H2 H3 H5
H4b
H6
C7
H2 a H2 b

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com 4
ASSEMBLY INSTRUCTIONS
Step 1
Slide a Crossbar end (C2) into the tube extensions on
a Leg assembly (C1) in the orientation shown for each
piece. Be sure to slide the Crossbar end in as far as it
will go. Then lock the Crossbar end in place using four
of the M8x8 Set screws (H1) using an Allen wrench.
Repeat this step with the other Crossbar end and Leg
assembly.
Step 3
Slide the Crossbar rails (C3) into the Crossbar end of
one of the assemblies from Step 1. Then, slide the sec-
ond assembly from Step 1 onto the opposite ends of
the Crossbar rails. Slide all parts together as far as they
will go. Doing so will make the full assembly easier to
lift onto the desktop in the next step.
Step 4
Before proceeding, inspect top surface of desktop
for damage. We recommend placing a blanket on the
oor to prevent the desktop from scratching. Place
the UPLIFT desktop on the oor, with the mounting
holes facing up. (If you are using your own desktop,
there will not be mounting holes).
Next, place the completed frame assembly on top
of the desktop, aligning the slots in the Leg assem-
blies with the metal inserts or pre-drilled holes in the
desktop (Step 5 will help you determine which holes
to use depending on your desktop’s size). If needed,
adjust the width of the frame in order to properly
align all of the holes.
Lift the frame slightly while aligning the holes to prevent
the rubber grommets from coming out of the Crossbar
ends or Leg assemblies. If a grommet does come out, it
can be easily replaced in its slot on the frame.
Step 2
Orient the Crossbar rails (C3) so that the Center indi-
cator marks are facing up.
Center indicator marks
C2 C1
H1
C3

5© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com
Step 5
Determine which holes to use.
This frame is designed to attach to UPLIFT desktops
from 48’’ to 80’’ wide and 24’’ or 30’’ deep. Refer to
the arrows in Fig A. for proper screw placement on
30’’ deep desktops and Fig. B for 24’’ deep desktops.
For 30’’ deep desktops, rst align the center slots of
the Leg assemblies with the three mounting holes
along each side of the desktop. Once the desktop
holes are aligned with the Leg assembly slots, you will
notice that one of the eight slots in each Crossbar end
will be closely aligned with a mounting hole toward
the middle of the desktop.
For 24’’-deep desktops, align the three mounting
holes along each side of the desktop with the outer
slots in the Leg assemblies, which allows the assembly
to be centered on the desktop. If the frame assembly
hangs off the front or back of the desktop, use the
outer slots on the opposite sides of the center slots.
Fig. A. 30’’ desktops
Fig. B. 24’’ desktops
Step 6
Determine which type of screw to use.
If your pre-drilled desktop does not have metal
threaded inserts, use the #10x3/4’’ Screws (H2a).
If your pre-drilled desktop does have metal threaded
inserts, use the #10-24x3/4’’ Screws (H2b).
After ensuring that the table frame is properly positioned,
attach the frame to the desktop using eight of the cho-
sen screws (H2a or H2b) and eight Washers (H3).
Make sure all screws are started before tightening
completely. Be careful not to over-tighten to avoid
stripping.
If you have purchased casters for your side table, in-
stall them now. Unscrew the leveling glides already in
the legs, and screw in the casters in their place.
or
H2 b
H2 a
C3 C4 C5
C9
H4a
H7
C6
H1 H2 H3 H5
H4b
H6
C7
C3 C4 C5
C9
H4a
H7
C6
H1 H2 H3 H5
H4b
H6
C7
C3 C4 C5
C9
H4a
H7
C6
H1 H2 H3 H5
H4b
H6
C7
C3 C4 C5
C9
H4a
H7
C6
H1 H2 H3 H5
H4b
H6
C7
H3
Step 7
Slide in each Crossbar rail (C3) until the Center indica-
tor mark is in the middle. Once this is done, the Cross-
bar rail will be centered and in the proper position.
Insert the eight remaining M8x8 Set screws (H1) into
the Crossbar ends (four on each side) to secure each
Crossbar rail, then tighten using the Allen wrench (H4).

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com 6
Step 8
With you and your friend on opposite ends of the ta-
ble assembly, grab the desktop with one hand and the
Leg assembly with the other hand, as shown.
Support both the frame and the desktop equally, and
gently rotate the table 90 degrees onto its side.
Readjust your grip and rotate another 90 degrees,
so that your table is right-side up. Adjust the leveling
studs or casters as needed to make the table level on
your oor.
Step 9
Position your table where you’d like it to be.
If you installed casters: Moving is easy! Make sure the
casters are unlocked and roll it to the desired location.
If you did not install casters: Using two people, lift
your desk (do not drag it) by holding onto the part of
the Leg assembly that is secured to the desktop.
Note: Never lift by holding on to the Desktop itself, as
this will put undue stress on the screws.

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com
Notes

512-614-3152
800-349-3839
[email protected]
upliftdesk.com
Work Better. Live Healthier
Copyright Notice: This guide is a component of the UPLIFT Desk™. This guide is a part of the scope of delivery, even if the item is resold. This guide
is also available on the UPLIFT Desk website: upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other published
form without the prior written consent of UPLIFT Desk. These instructions are subject to United States copyright law.
©
90.014.01.0604v.C - AI-FRM401-3.0
SAVE THESE INSTRUCTIONS
Study this manual carefully. If this desk is sold, please provide this
manual to the buyer, installers, or support personnel operating the product.
®