Uplift Desk CHR458 User manual

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
Step 3
Lower the chair assembly onto the Cylinder to secure it in place.
Package Contents
®
Vert Ergonomic Chair
CHR458
Step 4
The Headrest ts into the Back in a specic way. Look for the lower holes
on the rubber portion of the headrest (g. 01) and the recessed tab in the
Back (g. 02). These two parts t together.
Angle the Headrest, as shown. Lining up the slot on the Headrest with the
tabs on the Back, tilt it forward rmly, tting the two parts together.
Next, insert two (2) Socket pan head screws and tighten using the Allen wrench.
And nally place the two (2) Plastic caps over the screws.
(g. 01) (g. 02)
Step 2
Place the Seat upside down on the edge of a stable surface, such as a table.
Line up the holes for the Back and the Seat. Have a friend help keep it steady
while you attach the Back to the Seat. Using the Allen wrench, screw the Back
and Seat into place using three (3) Socket cap screws and three (3) Flat washers.
Note: The screws and washers may arrive partially inserted into the Back,
upon unboxing. Simply remove, and then attach the Seat and Back together.
CHR458/R01
Step 1
Insert the Casters into the holes on the Base, and press them rmly to secure
them in place.
Flip the Base, Casters down, onto the oor and insert the Cylinder into the Base
in the orientation shown, with the smaller diameter end up. Be cautious around
the end of the Cylinder to prevent it from getting oil on you or your clothes.
Allen wrench (L-shape)
Base Casters
(qty 5)
Back
(with armrests)
Socket cap screw (qty 3)
(M8x20)
Socket pan head screw (qty 2)
(M6x20)
Plastic cap (qty 2)
Flat washer (qty 3)
CylinderSeat Headrest

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
Seat Height
To adjust the Seat height, twist the lever on the right side of the seat. Stand up to
raise the chair higher or sit down in the chair to lower it.
Seat Depth
To adjust the Seat depth, pull out the handle on the right side near the front of the
Seat. Slide the seat forward or backward to your preferred position, then push the
handle back in to lock it into place.
Adjustment Guide
Back Tilt Adjustment
To unlock the Back, move the lever on the left of the Seat into the UP position.
This allows the back to “free oat” with you as you move and recline to any position
you wish within the chair’s range of recline. To lock the Back, move the lever into
the DOWN position.
If you prefer the back to be stationary, angle the seat to your preferred position
and twist the lever DOWN. This will lock the chair at the closest preset angle.
To unlock the back again or to change positions, ip the lever back and press back
slightly in the chair to disengage the lock.
locked unlocked
Lumbar Height
To adjust the chair’s lumbar support, grab the tabs on either side of the lumbar on the
back of the chair and slide it to the position that best supports your lumbar region.
Arm Height
To adjust armrest height press, the button underneath each armrest to unlock
and gently move them up or down to the height that best supports your arms.
Back Tilt Recline Tension
To adjust the chair’s recline twist, the dial underneath the Seat. Tightening or loosen-
ing it will allow you to set it at the level of recline tension you desire.
Flexible Back
The Vert moves with you as you move throughout a variety of positions. A exible
back that mimics the spine allows the chair to automatically adjust with your body
for more supportive and active seating.
Copyright Notice: These instructions are a component of the UPLIFT Vert Chair. These instructions are part of the scope of delivery, even if the item is resold. These instructions are also available on the UPLIFT Desk website:
upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other published form without the prior written consent of UPLIFT Desk. These instructions are subject to United States copyright law.
©
CAUTION: Read all instructions before assembly. Failure to assemble properly may result in
damage or personal injury.
WARNING: This product’s maximum weight capacity is 250 lbs. DO NOT exceed the maximum
weight capacity.
CAUTIONS & WARNINGS
!
!
!