Uplift Desk ACC009 User manual

Step 1
Place a plastic Mounting clip in the center of each exposed portion of the
steel bar on the Modesty panel. Make sure the clips are facing IN. Make sure
the wire management ap on the panel is facing the inside of the desktop so
you can place your wires in the pouch.
Mounting on the back of your desk
Mounting the 28.5’’ model on the side of your desk
Step 3
Once you decide on the placement, mark the location of the mounting clips
and holes with a pencil mark. Depending on the material of your desktop sur-
face, you may need to drill pilot holes. Use a drill with a 1/8” drill bit to make
pilot holes no deeper than 1/2’’. Attach using the 1/2’’ screws and a Phillips
head screwdriver.
CAUTION: If you have the 28.5’’ model, Do NOT use the 1’’ screws contained
in the Side-Mount Hardware Pack.
Step 4
After the modesty panel is secured, undo the panel’s Velcro and route your
cables through the inside mesh pocket. When all cables are in place, use the
Velcro to close the panel.
The 28.5’’ wide Modesty panels have the option to be mounted to the side
of your UPLIFT Desk.
If you choose to mount your 28.5’’ model to the side of the desk, open the
Side-Mount Hardware Pack and follow those instructions
Step 2
Center the modesty panel under the desktop about 1” from of the back edge*.
*NOTE: If you are clamping anything to the back edge of the desk, position
the modesty panel more toward the front of the desk as needed.
Package Contents:
ACC009~29 models only
Modesty Panel
(available in ve widths:
28.5’’, 41.5’’, 47.5’’, 59.5’’, and 71.5’’)
Mounting clips
(qty 2 for all models, except
71.5’’ which comes with three)
1/2’’ Screws
(qty 2 for all models, except
71.5’’ which comes with three)
Side-Mount Hardware Pack
contains hardware and instructions to
be used ONLY for the 28.5’’ model when
mounting to the side of your UPLIFT Desk.
© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
®
Modesty Panel
ACC009
ACC009/R03
Copyright Notice: These instructions are a component of the UPLIFT Modesty panel. These instructions are part of the scope of delivery, even if the item is resold. These instructions are also available on the UPLIFT Desk website:
upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other published form without the prior written consent of UPLIFT Desk. These instructions are subject to United States copyright law.
©
Side-Mount
Hardware
Pack
for
ACC009~29
29’’
Modesty
Panel
To
mount
it
to
the
BACK
of
your
desk, refer
to
the
other
instructions
and
hardware
contained
in
this
package.
The contents
in
this
pack
are
ONLY
to
be
used
for
mounting
your
Modesty
panel
to
the
SIDE
of
your
UPLIFT
Desk.
!CAUTION:
Read all instructions before assembly. Failure to assemble properly may result
in damage or personal injury.

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
®
Modesty Panel Dimensions
ACC009
28.5’’ model 41.5’’ model
47.5’’ model
59.5’’ model
71.5’’ model
Center of holes are
20’’ from the edges.
15"
15"
15"
59.5"
71.5"
Middle hole at 36’’
Center of outer holes
are approx 18‘’ from
the edges
Center of holes are
13’’ from the edges.
47.5"
7/
8"
41.5"
Center of holes are
11’’ from the edges.
15"
28.5"
Center of holes are
8’’ from the edges.