Upright X Series User manual

Safety Rules and Operating Instructions
Safety Rules and Operating Instructions
Operator Manual
WARNING
All personnel shall carefully read, understand and follow all safety rules,
operating instructions, and the Scaffold Industry Association’s MANUAL
OF RESPONSIBILITIES of ANSI A92.6-1999 before operating or
performing maintenance on any UpRight Aerial Work Platform.
Safety Rules
NEVER operate the machine without first surveying the work area for surface hazards such as holes,
drop-offs, bumps and debris.
NEVER operate the machine if all guardrails are not properly in place and secured with all fasteners prop-
erly torqued.
SECURE chain or gate across entrance after mounting platform.
NEVER use ladders or scaffolding on the platform.
NEVER attach overhanging loads or increase platform size.
LOOK up, down and around for overhead obstructions and electrical conductors.
DISTRIBUTE all loads evenly on the platform. See the back cover for maximum platform load.
NEVER use damaged equipment. (Contact UpRight for instructions. See toll-free phone number on back
cover.)
NEVER change operating or safety systems.
INSPECT the machine thoroughly for cracked welds, loose hardware, hydraulic leaks, damaged control
cable, loose wire connections and wheel bolts.
NEVER climb down elevating assembly with the platform elevated.
NEVER perform service on machine while platform is elevated without blocking elevating assembly.
NEVER recharge batteries near sparks or open flame; batteries that are being charged emit highly explo-
sive hydrogen gas.
AFTER USE secure the work platform against unauthorized use by turning key switch off and removing
key.
NEVER replace any component or part with anything other than original UpRight replacement parts with-
out the manufacturer’s consent.
NEVER operate the machine within
ten feet of power lines.
THIS MACHINE IS NOT INSULATED
NEVER elevate the platform or drive
the machine while elevated unless
the machine is on firm level surface.
NEVER sit, stand or climb on
guardrail or midrail.
X Series
Serial No. 15020 to Current

Page 2 X Series
This manual covers operation of the X Series Self Propelled Work Platforms. This manual must
be stored on the machine at all times.
Carefully read, understand and follow all safety rules, operating instructions, labels, and the Scaf-
fold Industry Association’s MANUAL OF RESPONSIBILITIES. Perform the following steps each
day before use.
1. Open module covers and inspect for damage, oil leaks, or missing parts.
2. Check the level of the hydraulic oil with the platform fully lowered. Open the Left Module and
remove the reservoir cap. Oil should be visible in the filler screen. Add hydraulic fluid if neces-
sary.
3. Check that fluid level in the batteries is correct (See “Battery Maintenance” on page 11.).
4. Verify that batteries are charged.
5. Check that A.C. extension cord has been disconnected from charger.
6. Check that all guardrails are in place with all fasteners properly tightened.
7. Check that the slide out deck extension is secured with the pin.
8. Inspect the machine thoroughly for cracked welds, loose or missing hardware, hydraulic leaks,
damaged control cable, loose wire connections and wheel bolts.
9. Close and secure module covers.
10. Move the machine, if necessary, to an unobstructed area to allow for full elevation.
11. Pull Chassis EMERGENCY STOP Switch to the ON position.
12. Pull Platform EMERGENCY STOP Switch to the ON position.
Figure 1: Chassis Controls
13. Turn and hold the Chassis Key
Switch to CHASSIS.
14. Push the Chassis Lift/Lower Switch
to LIFT to elevate the platform until
the Scissor Brace can be rotated to
the vertical position. Block the ele-
vating assembly as described on
page 10.
15. Visually inspect the elevating
assembly, lift cylinder, cables and
hoses for cracked welds, loose
hardware, hydraulic leaks, loose
wire connections and erratic opera-
tion. Check for missing or loose
parts.
16. Verify that the depression mecha-
nism has deployed into position
under each module. Remove the
scissor brace as described on
page 10.
17. Push the Chassis Lift/Lower Switch to LIFT and fully elevate the platform.
18. Partially lower the platform by pushing the Chassis Lift/Lower Switch to LOWER, and check
operation of the audible lowering alarm.
INTRODUCTION
PRE-OPERATION AND SAFETY INSPECTION
Chassis Key
Switch
Chassis
LIFT/LOWER
Switch Chassis EMERGENCY
STOP Switch

Page 3X Series
Figure 2: Emergency Lowering
19. Pull out on the Emergency Lowering
Knob to check for proper operation.
Once the platform has lowered,
release the knob.
20. Push the Chassis EMERGENCY
STOP Switch to check for proper
operation. All the machine functions
should be disabled. Pull out the
EMERGENCY STOP Switch to
resume.
21. Turn the Chassis Key Switch to
DECK.
22. Check that the route is clear of
obstacles (persons, obstructions,
holes, drop-offs, bumps, and
debris), is level, and capable of sup-
porting the wheel loads.
23. Mount the platform and properly
close the entrance.
Figure 3: Platform Controls
24. PLATFORM CONTROLS, Turn Lift/
Drive Switch to DRIVE.
NOTE: Use both HI and LOW drive (if
applicable) when performing
the following step.
25. Engage the Interlock Switch and
move the Control Handle FOR-
WARD, then REVERSE, to check for
speed control.
26. Push the Steering Switch RIGHT,
then LEFT, to check for steering con-
trol.
27. Turn the Lift/Drive Switch to LIFT.
28. Engage the Interlock Switch and
move the Control Handle forward to
check platform lift controls. Raise the
platform to full elevation.
29. Pull back on the Control Handle. The
platform should descend and the
audible lowering alarm should sound.
30. Lower the platform completely.
31. Push the Platform EMERGENCY
STOP Switch to check for proper
operation. All the machine functions
should be disabled. Pull out the Plat-
form EMERGENCY STOP Switch to resume.
Emergency Lowering Knob
Emergency Lowering Knob
Control
Handle with
Interlock
Switch
LIFT/ DRIVE
Switch
Platform EMERGENCY
STOP Switch
Steering
Switch

Page 4 X Series
Before operating work platform, ensure that the pre-operation safety inspection has been com-
pleted, and that any deficiencies have been corrected. Never operate a damaged or malfunc-
tioning machine. The operator must be thoroughly trained on this machine, and must read, fully
understand, and follow this Operator Manual and Scaffold Industry Association’s Manual of
Responsibilities of ANSI A92.6-1999.
PLATFORM EXTENSION
Figure 4: Platform Extension
1. Mount the platform and properly close the
entrance.
2. Depress the foot lever located at the rear of the
platform extension. Push the platform extension
forward until the pin engages the front stop.
3. To retract the platform extension, depress the
foot lever and pull the platform extension toward
the rear of the machine until the pin engages the
rear stop.
TRAVEL WITH PLATFORM LOWERED
1. Check that the route is clear of obstacles (per-
sons, obstructions, holes, drop-offs, bumps, and
debris), is level, and capable of supporting the
wheel loads.
2. Turn the Chassis Key Switch to DECK.
3. Pull Chassis EMERGENCY STOP Switch to the ON position.
4. Mount the platform and properly close the entrance.
5. Check clearances above, below and to the sides of platform.
6. Pull Platform EMERGENCY STOP Switch to the ON position.
7. Turn Lift/Drive Switch to DRIVE.
NOTE: Turn Lift/Drive Switch to HI (if applicable) for traveling on level ground, or to LOW
when extra torque is required for climbing grades.
8. Engage the Interlock Switch and move the Control Handle to FORWARD or REVERSE to
travel in the desired direction. The speed of the machine will vary depending on how far from
center the Control Handle is moved.
OPERATION

Page 5X Series
STEERING
1. Turn the Lift/Drive switch to DRIVE.
2. Engage the Interlock Switch, push the Steering Switch RIGHT or LEFT to turn the wheels in
the desired direction. Observe the tires while operating the machine to ensure proper direc-
tion.
NOTE: Steering is not self-centering. Wheels must be returned to the straight ahead
position by operating the Steering Switch.
ELEVATING THE PLATFORM
1. Select a firm, level surface.
2. Turn the Lift/Drive Switch to LIFT.
3. Engage the Interlock Switch and push the Control Handle forward.
4. If the machine is not level the tilt alarm will sound and the machine will not lift or drive. If the
tilt alarm sounds the platform must be lowered and the machine moved to a firm level
surface before attempting to re-elevate the platform.
TRAVEL WITH WORK PLATFORM ELEVATED
NOTE: The machine will travel at reduced speed when the platform is elevated.
1. Check that the route is clear of obstacles (persons, obstructions, holes, drop-offs, bumps, and
debris), is level, and capable of supporting the wheel loads.
2. Check clearances above, below and to the sides of platform.
3. Turn the Lift/Drive Switch to DRIVE.
4. Engage the Interlock Switch and move the Control Handle to FORWARD or REVERSE to
travel in the desired direction. The speed of the machine will vary depending on how far from
center the Control Handle is moved.
5. If the machine is not level, the tilt alarm will sound and the machine will not lift or drive. If the
tilt alarm sounds, the platform must be lowered and the machine moved to a firm level
surface before attempting to re-elevate the platform.
LOWERING THE PLATFORM
1. Turn the Lift/Drive Switch to LIFT.
2. Engage the Interlock Switch and pull back on the Control Handle to lower the platform.

Page 6 X Series
EMERGENCY LOWERING
Figure 5: Emergency Lowering Valve Handle
The Emergency Lowering Valve for the
X20N, X20W, and X26N is located at the
rear of the machine, above the charger.
The Emergency Lowering Valve for the
X31N is located at the rear of the
machine, to the left of the charger.
1. Open the Emergency Lowering Valve
by pulling and holding the knob.
2. To close, release the knob. The plat-
form will not elevate if the Emergency
Lowering Valve is open.
WARNING
!!
If the platform should fail to lower, NEVER climb down the elevating
assembly.
Emergency Lowering Knob
Emergency Lowering Knob

Page 7X Series
LOWER THE GUARDRAILS, X26N
This procedure applies only to the X26N model for the purpose of passing through a standard
double doorway. Guardrails must be returned to proper position before using the machine.
LOWERING PROCEDURE
1. Ensure that the slide out deck extension is fully retracted and deck pin is locked. Place the
Platform Controls on the platform.
2. Remove and retain the set screws from the side guardrails and the rollout deck guardrails.
3. Pull the four retaining pins and lower the rollout deck guardrail completely.
4. Pull the two retaining pins and lower the rear guardrail until it rests on the stop screws.
5. Pull the two retaining pins and lower the side guardrails completely.
6. Raise the rear guardrail until the retaining pins engage. Remove and retain the stop screws
and nuts from the rear guardrail.
7. Pull the two retaining pins and lower the rear guardrail completely.
RAISING PROCEDURE
1. Raise the rear guardrail until the retaining pins engage.
2. Install the stop screws and nuts on the rear guardrail and torque to 31 ft. lbs (42 N-m).
3. Pull the two retaining pins and lower the rear guardrail until it rests on the stop screws.
4. Pull the two retaining pins and raise the side guardrails until the tops are level with the rear
guardrail.
5. Raise the rear guardrail until the retaining pins engage.
6. Pull the four retaining pins and raise the roll out deck guardrail until the top is level with the
side guardrails.
7. Hang the controller on the roll out deck guardrail.
8. Install the set screws and torque to 31 ft. lbs (42 N-m).
FOLD DOWN GUARDRAILS, X31N
This procedure applies only to the X31N model for the purpose of passing through a standard
double doorway. Guardrails must be returned to proper position before using the machine.
FOLD DOWN PROCEDURE
1. Unhook the controller from the side guardrail and place it on the platform.
2. Pull the retaining pin on the front guardrail and rotate inwards.
3. Pull the retaining pin on the rear guardrail and rotate inwards.
4. Starting with the rollout deck guardrails and then the outer guardrails, lift up on each guardrail
and fold inwards.
ERECTION PROCEDURE
1. Starting with the outer guardrails and then the rollout deck guardrails, raise each guardrail
and drop it down securing it in the vertical position.
2. Rotate the front and rear upper guardrails outward and secure them to the opposite side
guardrails using the retaining pins.
3. Hang the controller on the side guardrail.
WARNING
!!
Before operating machine, guardrails must be securely fastened in their
proper position.

Page 8 X Series
AFTER USE EACH DAY
1. Ensure that the platform is fully lowered.
2. Park the machine on a firm, level surface, preferably under cover, secure against vandals, chil-
dren, and unauthorized operation.
3. Turn the Key Switch to OFF and remove the key to prevent unauthorized operation.
PARKING BRAKE RELEASE
Perform the following only when the machine will not operate under its own power and it is neces-
sary to move the machine or when winching onto a trailer to transport.
NOTE: X31N models have two identical brake adjustment nuts located on both sides of the
ladder. The X20N, X20W, and X26N have only one.
Figure 6: Parking Brake Release
The Brake Adjustment/Release
Nut(s) is/are located at the rear of
the machine to the right and/or left of
the ladder.
1. To release the brakes turn the
nut(s) counterclockwise until the
brakes disengage the tires.
2. The machine will now roll when
pushed or pulled.
3. To re-engage the brakes, turn the
nut(s) clockwise until the brakes
have fully engaged the tires.Ver-
ify that the brakes have fully
engaged the rear tires before
operating the machine by testing
their ability to hold the machine
on a 23% grade.
REAR
REAR
Parking Brake Release
Parking Brake Release
WARNING
!!
Never tow faster than 1 ft./sec. (0,3m/sec.)
Never operate work platform with the parking brakes released. Serious injury
or damage could result.

Page 9X Series
BYCRANE
Secure straps to Lugs only.
BYFORKLIFT
Figure 7: Transporting the Work Platform
Forklift from the rear of the machine
using the forklift pockets provided. If
necessary, the machine may be fork-
lifted from the side by lifting under the
Chassis Modules.
BYTRUCK
1. Maneuver the work platform into
transport position and chock the
wheels. The platform must be in
the fully lowered position for trans-
port.
2. Secure the work platform to the
transport vehicle by attaching
chains or straps of adequate load
capacity to the front and rear Tie
Downs.
TRANSPORTING THE WORK PLATFORM
WARNING
!!
Forklifting is for transporting only.
See specifications for weight of the work platform and be certain that forklift is
of adequate capacity to lift the platform.
Rear Tie Down/Lift Lugs
Front Tie Down Lugs
Lift Lugs
REAR
Forklift Pockets
FRONT
CAUTION
!!
Front tie down lugs are not to be used to lift work platform.
Overtightening of chains or straps attached to tie down lugs may result in
damage to work platform.

Page 10 X Series
Figure 8: Blocking the Elevating Assembly
BLOCKING ELEVATING ASSEMBLY
INSTALLATION
1. Park the work platform on a firm level surface.
2. Pull Chassis EMERGENCY STOP Switch to the ON
position.
3. Pull Platform EMERGENCY STOP Switch to the ON
position.
4. Turn and hold the Chassis Key Switch to CHASSIS.
5. Push the Chassis Lift/Lower Switch to LIFT to elevate
the platform until the Scissor Brace can be rotated to
the vertical position.
6. X20N, X20W, and X26N-From rear of machine, lift the
Scissor Brace from its stowed position. Rotate upward
and outward then down until it is hanging vertical
below its attachment point.
7. X31N-From the left side of the machine, pull the lock-
ing pin securing the brace. Rotate the Scissor Brace
counterclockwise until it is in the vertical position.
8. Lower the platform by pushing the Chassis Lift/Lower
Switch to LOWER and gradually lower the platform
until the Scissor Brace is supporting the platform.
REMOVAL
1. Using the Chassis Controls, gradually elevate the plat-
form until the Scissor Brace is clear.
2. X20N, X20W, and X26N-Rotate Scissor Brace out-
ward and upward over its mounting point until it rests
in the stowed position.
3. X31N-Rotate scissors brace clockwise until the locking
pin engages.
4. Lower the platform by pushing the Chassis Lift/Lower
Switch to LOWER to completely lower the platform.
MAINTENANCE
WARNING
!!
Never perform service while platform is elevated without first blocking the
elevating assembly.
DO NOT stand in elevating assembly area while deploying or storing brace.
DO NOT block elevating assembly with a load on the platform.
BRACE RESTS ON
WELDMENT WHEN IN
BLOCKING POSITION
ROTATE BRACE
CLOCKWISE
TO BLOCK
PIN RESTS ON
BRACE WHEN IN
BLOCKING POSITION
SCISSOR BRACE
IN REST POSITION
BRACE ROTATES
TO BLOCKING
POSITION
BRACE RESTS ON
PIN WHEN IN
BLOCKING POSITION
X20N, X20W, and X26N
X31N

Page 11X Series
BATTERY MAINTENANCE
Figure 9: Power Module
• Check the battery fluid level daily, espe-
cially if the work platform is being used
in a warm, dry climate.
• If the electrolyte level is lower than 3/8
in. (10 mm) above the plates, add dis-
tilled water only. DO NOT use tap water
with high mineral content, as it will
shorten battery life.
• The battery and cables should be
inspected regularly for signs of cracks
in the case, electrolyte leakage and
corrosion of the terminals. Inspect
cables for worn spots or breaks in the
insulation and for broken cable termi-
nals. Keep terminals and tops of batter-
ies clean.
• Refer to the Service Manual to extend battery life and for complete service instructions.
WARNING
!!
Hazard of explosive gas mixture. Keep sparks, flame, and smoking material
away from batteries.
Always wear safety glasses when working near batteries.
Battery posts, terminals and related accessories contain lead and lead
compounds, chemicals known to the State of California to cause cancer and
reproductive harm. Wash hands after handling.
Battery fluid is highly corrosive. Thoroughly rinse away any spilled fluid with
clean water.
Always replace batteries with UpRight batteries or manufacturer approved
replacements weighing 62 lbs. (28 kg.) each.
Remove to check fluid

Page 12 X Series
BATTERY CHARGING
Figure 10: Battery Charger
Charge the batteries at end of each work
shift or sooner if batteries have been dis-
charged.
1. Check battery fluid level. If electrolyte level is lower than 3/8 in. (10 mm) above plates add dis-
tilled water only.
2. Connect an extension cord to the battery charger plug. Plug the extension cord (12 gauge [1.5
mm²] minimum conductor diameter; 50 ft. [15m] maximum length) to properly grounded outlet
of correct voltage and frequency.
3. The battery charger turns on automatically after a short delay.
NOTE: The battery charger circuit must be used with a GFI (Ground Fault Circuit Interrupt)
outlet.
DO NOT operate the machine while charger is plugged in.
Charger
Charger Plug
(behind plate)
REAR
WARNING
!!
Charge batteries only in a well ventilated area.
Do not charge the batteries if the work platform is near a source of sparks or
flames.
Permanent damage to the batteries will result if the batteries are not
recharged immediately after discharging.
Never leave the battery charger operating for more than two days.
Never disconnect the cables from the batteries when the battery charger is
operating.
Keep the battery charger dry.

Page 13X Series
FRONT
REAR
FRONT
LEFT MODULE
RIGHT MODULE
061787-001
!
DANGER
OF PLATFORM BEFORE OPERATING MACHINE.
THIS BAR MUST BE PINNED IN POSITION ACROSS END
X31N Platform
MAXIMUM SIDE LOAD 200 LBS.
OR 4 OCCUPANTS
PLATFORM LOAD 1000 LBS.
MAXIMUM DISTRIBUTED
WARNING
!
101250-003
MAXIMUM SIDE LOAD 150 LBS.
OR 3 OCCUPANTS
PLATFORM LOAD 1000 LBS.
MAXIMUM DISTRIBUTED
WARNING
!
101250-004
MAXIMUM SIDE LOAD 150 LBS.
OR 3 OCCUPANTS
PLATFORM LOAD 700 LBS.
MAXIMUM DISTRIBUTED
WARNING
!
101250-005
MAXIMUM SIDE LOAD 113 LBS.
OR 2 OCCUPANTS
PLATFORM LOAD 750 LBS.
MAXIMUM DISTRIBUTED
WARNING
!
101250-002
1600 LBS.
WHEEL LOAD
MAXIMUM
101252-004
1750 LBS.
WHEEL LOAD
MAXIMUM
101252-005
1850 LBS.
WHEEL LOAD
MAXIMUM
101252-006
EMERGENCY
DOWN VALVE
LOWER PLATFORM
PULL KNOB TO
!
DANGER
TIP-OVER HAZARD
MAXIMUM DISTRIBUTED LOAD
250 LBS. OR 1 OCCUPANT
ON EXTENDED DECK
MAXIMUM SIDE LOAD 100 LBS.
061220-002
1 Required
066560-010
1 Required
X20W, X26N, X31N
066560-011
1 Required
X20N
066555-000
1 Required
060197-000
1 Required
066554-000
1 Required
066554-000
1 Required
066550-000
1 Required
061787-001
1 Required
X31N
066558-000
1 Required
X20N, X20W, X26N
005223-003
1 Required
X31N
014222-003-99
2 Required
101250-004
2 Required
X26N
101250-005
2 Required
X31N
101250-002
2 Required
X20N
101250-003
2 Required
X20W
061205-005
1 Required
066522-000
1 Required
066559-000
1 Required
101252-004
1 Required
X20N, X20W
101252-005
1 Required
X26N
101252-006
1 Required
X31N
066561-002
1 Required
X31N
066556-000
2 Required
066561-000
1 Required
X20N, X20W, X26N
101251-000
1 Required
005221-000
1 Required
062562-001
1 Required
066553-000
2 Required
066556-001
4 Required
066552-000
1 Required
010076-001
1 Required
NOTE: Labels can be ordered by using Part Number located by each label. For machines
equipped with options consult the Service Manual.
Proper label installation is required. All of these labels shall be present and in
good condition before operating the work platform. Be sure to read, understand
and follow these labels BEFORE operating the work platform.

Page 14 X Series
The complete inspection consists of periodic visual and operational checks, along with periodic
minor adjustments that assure proper performance. Daily inspection will prevent abnormal wear
and will prolong the life of all systems. The inspection and maintenance schedule is to be per-
formed at regular intervals. Inspection and maintenance shall be performed by personnel who are
trained and familiar with mechanical and electrical procedures.
The preventative maintenance table has been designed for machine service and maintenance
repair. Please photocopy the following page and use the table as a checklist when inspecting the
machine for service.
PREVENTATIVE MAINTENANCE
WARNING
!!
Before performing preventative maintenance, familiarize yourself with the
operation of the machine.
Always block the elevating assembly whenever it is necessary to perform
maintenance while the platform is elevated.

Page 15X Series
PREVENTATIVE MAINTENANCE CHECKLIST
PREVENTATIVE MAINTENANCE KEY
Interval
Daily=each shift or every day
50h/30d=every 50 hours or 30 days
250h/6m=every 250 hours or 6 months
1000h/2y=every 1000 hours or 2 years
Y=Yes/Acceptable
N=No/Not Acceptable
R=Repaired/Acceptable
PREVENTATIVE MAINTENANCE REPORT
Date: _______________________________________
Owner: _____________________________________
Model No: ___________________________________
Serial No: ___________________________________
Serviced By: _________________________________
Service Interval: ______________________________
COMPONENT INSPECTION OR SERVICES INTERVAL Y N R
Batteries
Check electrolyte level Daily
Check specific gravity 6m
Clean exterior 6m
Check battery cable condition Daily
Clean terminals 6m
Hydraulic Oil
Check oil level Daily
Change filter 6m
Drain and replace oil 2y
Hydraulic
System
Check for leaks Daily
Check hose connections 30d
Check hoses for exterior wear 30d
Emergency
Hydraulic
System
Operate the emergency lowering valve and
check for serviceability Daily
Chassis
Controls Check switch operation Daily
Platform
Controls Check switch operation Daily
Control Cable Check the exterior of the cable for
pinching, binding or wear 6m
Platform
Deck and
Rails
Check fasteners for proper torque Daily
Check welds for cracks Daily
Check condition of deck Daily
Tires Check for damage Daily
Check lug nuts (torque to 90 ft. lbs.) 6m
Hydraulic
Pump
Wipe clean 30d
Check for leaks at mating surfaces 30d
Check for hose fitting leaks Daily
Check mounting bolts for proper torque 6m
Drive Motors Check for operation Daily
Steering
System
Check hardware & fittings for proper
torque 6m
Grease pivot pins 30d
Check steering cylinder for leaks 30d
Elevating
Assembly
Inspect for structural cracks Daily
Check pivot points for wear 6m
Check mounting pin pivot bolts for proper
torque 6m
Check elevating arms for bending 6m
Chassis
Check hoses for pinch or rubbing points Daily
Check component mounting for proper
torque 6m
Check welds for cracks Daily
Tilt Sensor Check for operation 6m
Lift Cylinder
Check the cylinder rod for wear 30d
Check mounting pin pivot bolts for proper
torque 6m
Check seals for leaks 30d
Inspect pivot points for wear 6m
Check fittings for proper torque 6m
Entire Unit
Check for and repair collision damage Daily
Check fasteners for proper torque 6m
Check for corrosion-remove and repaint 6m
Lubricate 30d
Labels Check for peeling, missing, or unreadable
labels & replace Daily
COMPONENT INSPECTION OR SERVICES INTERVAL Y N R

1775 Park Street
Selma, California 93662
TEL: (800) 926-LIFT or [phone]
FAX: [phone]
Parts FAX: [phone]
http://www.upright.com
060572-005
04-00 D
Local Distributor:
Safety Rules and Operating Instructions
Safety Rules and Operating Instructions
SPECIFICATIONS
Specifications are subject to change without notice. Hot weather or heavy use may reduce performance.
Meets or exceeds all applicable requirements of OSHA and ANSI A92.6-1999
ITEM X20N X20W X26N X31N
Platform Size w/ Extension 28 in. x 87 in.
[0,7 m x 2,21 m]
44 in. x 87 in.
[1,12 m x 2,21 m]
46.25 in. x 87 in.
[1,17 m x 2,21 m]
46.25 in. x 87 in.
[1,17 m x 2,21 m]
Max. Platform Capacity
Standard 750 lbs. [340 kg] 1000 lbs. [453 kg] 1000 lbs. [453 kg] 700 lbs. [318 kg]
on Extension 250 lbs. [110 kg] 250 lbs. [110 kg] 250 lbs. [110 kg] 250 lbs. [110 kg]
Max. No. of occupants
Standard (total) 2 people 4 people 3 people 3 people
on Extension 1 person 1 person 1 person 1 person
Height
Working Height 26 ft. [7,9 m] 26 ft. [7,9 m] 32 ft. [9,75 m] 37 ft. [11,28 m]
Max. Platform Height 20 ft. [6,1 m] 20 ft. [6,1 m] 26 ft. [7,92 m] 30.5 ft. [0,8 m]
Min. Platform Height 38 in. [0,97 m] 38 in. [0,97 m] 43 in. [1,1 m] 48 in. [1,2 m]
Dimensions
Weight 3,828 lbs. [1656 kg] 4,273 lbs. [1858 kg] 4,747 lbs. [2072 kg] 5480 lbs. [2485,7 kg]
Overall Width 32.5 in. [0,83 m] 48 in. [1,22 m] 48 in. [1,22 m] 48 in. [1,22 m]
Overall Height 78.5 in. [2 m] 78.5 in. [2 m] 83.5 in. [2,1 m] 88.5 in. [2,25 m]
Overall Length, Extension In 92.5 in. [2,3 m] 92.5 in. [2,3 m] 92.5 in. [2,3 m] 92.5 in. [2,3 m]
Overall Length, Extension Out 128.5 in. [3,26 m] 128.5 in. [3,26 m] 128.5 in. [3,26 m] 128.5 in. [3,26 m]
Drivable Height 20 ft. [6,1 m] 20 ft. [6,1 m] 26 ft. [7,93 m] 30.58 ft. [9,3 m]
Drive Speed
Platform Lowered 0 to 2.0 mph [0 to 3,2 km/h]
Platform Raised 0 to 0.62 mph [0 to 1 km/h]
Energy Source 24 Volt Battery Pack (4-220 Amp Hour, 6 Volt Batteries, min. wt. 62 lbs. [28,12 kg] each)
Motor 24 Volt 4 Horse Power DC Electric Motor
System Voltage 24 Volt DC
Battery Charger 25 AMP, 110/220 VAC
Battery Duty Cycle 25% for 8 Hours
Hydraulic Tank Capacity 4 Gallons [15,2 l] 4 Gallons [15,2 l] 4 Gallons [15,2 l] 5 Gallons [19 l]
Maximum Hydraulic Pressure 3000 psi [206,8 bar]
Lift System One Single Stage Lift Cylinder One Single Stage Lift Cylinder One Single Stage Lift Cylinder Two Single Stage Lift
Cylinders
Lift Speed Raise, 35 sec./Lower 30 sec. Raise, 40 sec./Lower 30 sec. Raise, 45 sec./Lower 40 sec. Raise, 65 sec./Lower 40 sec.
Control System Control Handle with Interlock Switch, Rotary Drive/Lift Switch, and Red Mushroom EMERGENCY STOP Switch
Drive System Dual Front Wheel Hydraulic Motors
Tires 15 in. [381 mm] Diameter Solid Rubber, non-marking
Parking Brake Dual Spring Applied, Hydraulic Release
Turning Radius 8 in. [254 mm] Inside
Maximum Gradeability 23% [13°] 23% [13°] 22% [12°] 20% [11° ]
Wheel Base 74.75 in. [1,9 m]
Guardrails 40 in. [1,02 m] High
Toeboard 6 in. [152 mm] High