urmet domus IMAGO 1707/1 User manual

sec. new 2009
−−−−
1
2GO! - Technical manual
ne
W
SECTION NEW 2009
NEWS
2009
IMAGO HANDS-FREE COLOUR TFT 4”
VIDEO DOOR PHONE Ref. 1707/1 2
BLACK/WHITE VIDEO DOOR PHONE
Ref. 1740/1 5
COLOUR VIDEO DOOR PHONE Ref. 1740/40 6
BLACK/WHITE VIDEO DOOR PHONE
Ref. 1715/1 10
Download from www.urmetdomus.com Technical Manuals area.
SECTION CONTENTS

2
−−−−
sec. new 2009 2GO! - Technical manual
ne
W
IMAGO HANDS-FREE COLOUR TFT 4” VIDEO DOOR PHONE Ref. 1707/1
SPECIFICATIONS
TECHNICAL SPECIFICATIONS
IMAGO HANDS-FREE COLOUR TFT 4” VIDEO DOOR PHONE
IMAGO HANDS-FREE COLOUR TFT 4” VIDEO
DOOR PHONE Ref. 1707/1
The Imago video door phone has been designed by architect Trabucco
and is provided with a dedicated call loudspeaker and 3-level call tone
volume adjustment (high-low-mute).
Imago is equipped with additional buttons for additional services and
with an OSD display that allows adjustment of colour, brightness and
contrast directly from the display, using a joystick on the video door
phone. During the installation it is possible to choice the video door
phone operating mode: Hands-free or Button pressed. In the first case,
after receiving a call, press the Audio on button to start conversation,
and press again the same button to stop it; in the second case, keep
the Audio ON button pressed during all the conversation time.
SPECIFICATIONS
The main characteristics of the video door phone are:
Flat 4” LCD colour module.
Call tone volume adjustment and call tone exclusion function (Mute).
In Mute mode (call excluded) is visible a mechanical red signal.
MUTEMAX. MIN.
When volume is set to “MUTE” the video door phone will not ring
but the video module will light up.
•
•
§
1
2
6
7
8
34
5
10
9
220 mm
124 mm
1AUXILIARY BUTTONS: these can be used for specific functions
according to the system.
2JOYSTICK: this is used to adjust the video parameters.
3The left joystick button is used to decrease video parameters.
4The right joystick button is used to increase video parameters.
5SELECT: This button is used to select the video parameter to be
adjusted.
6AUTO-ON BUTTON
7DOOR OPENER BUTTON: This turns green when the video
door phone is on. It turns red to indicate that the door is open
and blinks red to indicate that the automatic door opening
function is on.
8AUDIO BUTTON: This turns green when the video door phone
is on. The button will turn amber when the audio button is
pressed.
9CALL VOLUME/MUTE CONTROL
10 MUTE INDICATOR: A tab protrudes from the left-hand side of
the video door phone when the volume is muted.
TECHNICAL SPECIFICATIONS
Power voltage: 16 ÷ 26Vcc
Working: max 0,36A
PAL version: Vertical frequency: 50Hz ± 5Hz
Horizontal frequency: 15625 ± 100Hz
Video signal: 1Vpp ± 10%
Kinescope: 4” TFT (with OSD)
Video impedance: >10KW
Resolution: 960 (H) x 234 (V) dot
Receiving capsule: 45speaker
OSD Menu Control: Brightness, Contrast and Colour
Max. call volume: 85dB
Transmitting capsule: electret microphone
Button voltage: 24Veff. max
Button current: 0,5Aeff
Operating temperature range: -5° ÷ +50°C
Max. humidity: 90% UR
Ref. 1707/1

sec. new 2009
−−−−
3
2GO! - Technical manual
ne
W
IMAGO HANDS-FREE COLOUR TFT 4” VIDEO DOOR PHONE Ref. 1707/1
BRACKETS FOR IMAGO VIDEO DOOR PHONE
INSTALLATION
IMAGO HANDS-FREE COLOUR TFT 4” VIDEO DOOR PHONE Ref. 1707/1
BRACKETS FOR IMAGO VIDEO DOOR PHONE
The Imago video door phone is supplied without bracket that must be
purchased separately.
Kit Ref. 1707/701 including the following devices:
System 2GO! bracket Ref. 1707/82
One-user distributor Ref. 1082/51
The one-user distributor must be installed only for video door
phones connected in extension configuration. The distributor is
not required with connections in in-out configuration.
The bracket fits connection terminals, programming dip switches and
line terminal switch.
A yellow LED is provided for checking correct reception of the video
signal. The LED comes on if reception is not optimal.
(IN/OUT)
LINE
(DER)
LINE
ON
OFF
1082/51 PATENTED
1
2
3
4
5
6
1Yellow indicator LED
2Apartment internal code dip switch (INT)
3User code dip switch (CODE)
4Line terminal switch
5Terminal board
6One-user distributor
BRACKET TERMINAL BOARD
LINE IN
}
Non-polarised bus line
LINE IN
LINE OUT
}
Not polarized Bus line for line output connection
LINEOUT
S+ Supplementary ringer connection positive
S- Supplementary ringer connection negative
CP
}
Floor call button
CP
TECHNICAL SPECIFICATIONS Ref. 1707/701
Max. bracket draw with monitor on: 550mA
Max. bracket draw in standby: 11mA
Working one-user distributor: 8 ÷ 12mA
DEFAULT PROGRAMMING
User code: 31
Indoor station code: 0
Line termination: ON
•
•
§
INSTALLATION
Fasten the bracket to the wall with screws and bolts respecting the
side dimensions.
10 cm 10 cm
1,55 m
Connect the non-polarised Bus line wire to the LINE IN terminals.
To use the floor call or supplementary ringer function, connect the
respective wires.
Fit the video door phones on the brackets after checking that the
bracket yellow LEDs are off.
Remove the cardboard protection.
Fasten the video door phone as shown in the figure.
To replace the video door phone, press the hook αand turn it
clockwise.
α
•
•
•
•
•
•
•

4
−−−−
sec. new 2009 2GO! - Technical manual
ne
W
TONE SELECTION
Five tones can be selected on 2GO! system indoor stations. The tones
can be programmed also by the end user by following the simple
sequence below.
DOOR PHONE CALL TONE
Five tones can be selected on 2GO! system indoor stations. The tones
can be programmed also by the end user by following the simple
sequence below:
1. Hold the door opener button pressed. Press and release the
button. The indoor station will play a tone.
2. Hold the door opener button pressed and press the button
again to change the tone.
3. Release the door opener button when you have chosen the
tone you want. The tone is now programmed.
FLOOR CALL TONE
Five floor call tones can be selected on 2GO! system indoor stations.
The tones can be programmed also by the end user by following the
simple sequence below:
1. Hold the door opener button pressed. Press and release the
button . The indoor station will play a tone.
2. Hold the door opener button pressed and press the button
again to change the tone.
3. Release the door opener button when you have chosen the
tone you want. The tone is now programmed.
PROGRAMMING DATA DELETION (RESTORE
DEFAULT SETTINGS)
Proceed as follows to delete all optional programming data:
1. Holding button pressed, press button . The video door
phone will beep twice to indicate that it is in programming mode.
Button will start blinking red.
2. Press and at the same time for 3 seconds until you hear the
deletion tone.
3. Press the apartment station button . The video door phone will
beep when you exit programming. Button will go out.
IMAGO HANDS-FREE COLOUR TFT 4” VIDEO DOOR PHONE Ref. 1707/1
TONE SELECTION
CONTRAST, BRIGHTNESS, COLOUR ADJUSTMENT
IMAGO HANDS-FREE COLOUR TFT 4” VIDEO DOOR PHONE Ref. 1707/1
CONTRAST, BRIGHTNESS, COLOUR
ADJUSTMENT
These video parameters can be adjusted only when the video door
phone is on, after receiving a call or selecting the auto-on function.
Use the joystick button (2) to access the setting menu.
Press the right button (4) to increase and the left button (3) to
decrease.
Press the SELECT (5) to go to the next parameter in the following
sequence:
contrast
exit
OSD menu
brightness colour
reset
The RESET is used to return all parameters to the initial condition.
Press either the right or the left button of the joystick to reset the
parameters. Press the middle button to exit the setting menu.
The changes will not be stored if the video door phone goes out
before exiting setting mode.
•
•
•

sec. new 2009
−−−−
5
2GO! - Technical manual
ne
W
SIGNO BLACK/WHITE VIDEO DOOR PHONE Ref. 1740/1
SIGNO BLACK/WHITE VIDEO DOOR PHONE Ref. 1740/1
BRACKETS FOR IMAGO VIDEO DOOR PHONE
INSTALLATION
SIGNO BLACK/WHITE VIDEO DOOR PHONE
Ref. 1740/1
The Signo video door phone, designed by architect Citterio, is
provided with 1 button for door lock release backlit with a blue led,
3 buttons for additional services, call tone volume adjustment with
function “Mute”.
It is equipped with a special handset that allows deaf people,
provided with a suitable earphone, to hear who is speaking from the
push button panel.
The video door phone is easy to install, because no masonry is
necessary and all connections can be done on the bracket to which
it will be fastened.
SPECIFICATIONS
The main characteristics of the video door phone are:
Flat 4” black and white video module.
Call tone volume adjustment and call exclusion function (Mute). The
Mute function is signalled by a red indicator on the front side.
MAX. MIN. MUTE
When volume is set to “MUTE” the video door phone will not ring
but the video module will light up.
The door lock release button is backlit by led when the video
module is on.
Service buttons ( , , ), for example for the activation of additional
electric locks, stairs lights, video door phone auto-on, etc.
Adjustable brightness and contrast.
•
•
§
•
•
•
1
5
2
3
4
225 mm
50 mm
205 mm
1Door opener button
2Auxiliary buttons
3Contrast adjustment control
4Brightness adjustment control
5Call volume control and adjustment
TECHNICAL SPECIFICATIONS
Power voltage: 16 ÷ 18,5Vcc
Working: Uptake: max 0,35A
Stand-by: 0A
Working power: max 6,5W
CCIR version: Vertical frequency: 50Hz ± 2Hz
Horizontal frequency: 15625 ± 300Hz
Video signal: 1Vpp 75nominal
1Vpp -6dB minimum
Kinescope: 4” flat 13mm neck
Phosphorous: P45
Screen size: 81 x 59mm
Geometric distorsion: vert. 5% max.
horiz. 5% max.
barrel 10% max.
Brightness: 170cd/m2max. setting
X-rays: none
Switch-on delay: 4sec. Max
Transmitting capsule: electret microphone
Receiving capsule: 45speaker
Buttons contacts range: 0,5A @ 18Vdc
Operating temperature range: -5° ÷ +50°C
Max. humidity: 90% UR

6
−−−−
sec. new 2009 2GO! - Technical manual
ne
W
SIGNO COLOUR VIDEO DOOR PHONE
Ref. 1740/40
The Signo video door phone, designed by architect Citterio, is a colour
apartment station that, as for the black/white version, is provided with
a door lock release button backlit with blue led, 3 buttons for additional
services, call tone volume adjustment with “Mute” function.
It is equipped with a special handset that allows deaf people,
provided with a suitable earphone, to hear who is speaking from the
push button panel.
The video door phone is easy to install, because no masonry is
necessary and all connections can be done on the bracket to which
it will be fastened.
SPECIFICATIONS
The main characteristics of the video door phone are:
4” LCD colour flat video module.
Call tone volume adjustment and call exclusion function (Mute). The
Mute function is signalled by a red indicator on the front side.
MAX. MIN. MUTE
When volume is set to “MUTE” the video door phone will not ring
but the video module will light up.
The door lock release button is backlit by led when the video
module is on.
Additional buttons ( , , ) for special decoder activation, auto
power-on, Intercom calling and advanced programming.
Image brightness and colour adjustment.
•
§
•
•
•
1
5
2
3
4
225 mm
50 mm
205 mm
1Door opener button
2Auxiliary buttons
3Colour adjustment control
4Brightness adjustment control
5Call volume control and adjustment
TECHNICAL SPECIFICATIONS
Power voltage: 16 ÷ 18,5Vcc
Working Uptake: max 0,35°A
Stand-by: 0A
Working power: max 6,5W
CCIR version Vertical frequency: 50Hz ± 2Hz
Horizontal frequency: 15625 ± 300Hz
Video signal: 1Vpp 75 nominal
1Vpp -6 dB minimum
LCD: 4” backlit
Screen size: 81 x 59mm
Resolution: 380H x 250V pixel
Colour system: PAL
Switch-on delay: 4sec. Max
Transmitting capsule: electret microphone
Receiving capsule: 45speaker
Buttons contacts range: 0,5A @ 18Vdc
Operating temperature range: -5° ÷ +50° C
Max. humidity: 90% UR
SIGNO COLOUR VIDEO DOOR PHONE Ref. 1740/40
SPECIFICATIONS
TECHNICAL SPECIFICATIONS
SIGNO COLOUR VIDEO DOOR PHONE Ref. 1740/40

sec. new 2009
−−−−
7
2GO! - Technical manual
ne
W
SIGNO BRACKET AND ONE-USER
DISTRIBUTOR KIT Ref. 1740/701
The Signo video door phone is supplied without bracket that must be
purchased separately.
Kit Ref. 1740/701 including the following devices:
System 2GO! bracket Ref. 1740/82
One-user distributor Ref. 1082/51
The one-user distributor must be installed only for video door
phones connected in extension configuration. The distributor is
not required with connections in in-out configuration.
The bracket fits connection terminals, programming dip switches and
line terminal switch.
A yellow LED is provided for checking correct reception of the video
signal. The LED comes on if reception is not optimal.
(IN/OUT)
LINE
(DER)
LINE
ON
OFF
1082/51 PATENTED
1
2
3
4
5
6
1User code dip switch (CODE)
2Apartment internal code dip switch (INT)
3Yellow indicator LED
4Line terminal switch
5Terminal board
6One-user distributor
BRACKET TERMINAL BOARD
LINE
}
Non-polarised bus line
LINE
S+ Supplementary ringer connection positive
S- Supplementary ringer connection negative
CP
}
Floor call button
CP
To use the floor call or supplementary ringer function, remove the
dedicated terminal protection and connect the respective wires.
TECHNICAL SPECIFICATIONS Ref. 1740/701
Max. bracket draw with monitor on: 550mA
Max. bracket draw in standby: 11mA
Working one-user distributor: 8 ÷12mA
•
•
§
DEFAULT PROGRAMMING
User code: 31
Indoor station code: 0
Line termination: ON
INSTALLATION
Proceed as follows to install the Signo video door phone and the
respective bracket:
1. Arrange the duct so that it ends in correspondence with the input
hole on the bracket.
2. Fasten the bracket to the wall at the height from the floor shown
by means of the four screws.
1,55 m
Ref. 1740/82
3. Remove the card board protection.
4. Connect the wires to the specific terminals.
5. Configure the dip switches as shown in the “System installation
and activation” section.
Complete system installation and power the system up before
fastening the video door phone to the bracket. Check that
the yellow LED on the brackets is off. Otherwise proceed as
follows:
Check correct setting of line terminal.
Check programmed settings of apartment stations and
brackets.
Split the system up to isolate the part which generates video
signal transmission and reception problems.
6. Extract the retainer hook αand pulling the hook downwards.
7. Fasten the video door phone to the bracket as shown in the
figure.
The switch can be either in position “A” or in position “B” on
video door phones.
8. Fasten the video door phone by pushing the retainer hook α
upwards.
α
§
•
•
•
§
SIGNO VIDEO DOOR PHONE
SIGNO VIDEO DOOR PHONE
SIGNO BRACKET AND ONE-USER DISTRIBUTOR KIT Ref. 1740/701

8
−−−−
sec. new 2009 2GO! - Technical manual
ne
W
TONE SELECTION
Five tones can be selected on 2GO! system indoor stations. The tones
can be programmed also by the end user by following the simple
sequence below.
DOOR PHONE CALL TONE
Hold the door opener button pressed. Press and release the button
. The indoor station will play a tone.
Hold the door opener button pressed and press the button again
to change the tone.
Release the door opener button when you have chosen the tone
you want. The tone is now programmed.
The selected tone will be the same for all door phone calls. The source
of the call can however be distinguished by timing the tone:
Call origin Time
Call from main door unit 3s ON
Call from secondary door unit 0,4s ON-0,2s OFF for 5 times
Intercom call 0,5s ON-0,5s OFF for 5 times
FLOOR CALL TONE
Five floor call tones can be selected on 2GO! system indoor stations.
The tones can be programmed also by the end user by following the
simple sequence below.
Hold the door opener button pressed. Press and release the button .
The indoor station will play a tone.
Hold the door opener button pressed and press the button again
to change the tone.
Release the door opener button when you have chosen the tone
you want. The tone is now programmed.
–
–
–
–
–
–
PROGRAMMING DATA DELETION
Proceed as follows to delete all optional programming data:
Hold the door opener button pressed and pick up the handset.
Press and at the same time for 3 seconds until you hear the
deletion tone.
Release buttons and and hang up.
ACCESSORIES FOR SIGNO VIDEO DOOR
PHONES
ADD-ON Ref. 1083/96
A special add-on module Ref. 1083/96 can be purchased separately
and combined with basic monitors in intercom systems where up to 6
buttons, 2 LEDs and a switch are required.
FUNCTION
AUTOMATIC DOOR OPENER FUNCTION
This function can be switched on and off by means of the dedicated
button on the Ref. 1083/96 add-on. The green LED will light up
when the function is on. A door opener command is transmitted when
a call from a door unit is received. Program this function on one of the
indoor stations only if there are several indoor stations in parallel.
MASTER DOOR UNIT OPEN DOOR FUNCTION
The indoor stations can monitor the physical state of the Master door
by connecting a sensor to the SP/GND terminals. The red LED on the
Ref. 1083/96 will light up when the door is open.
INTERCOM CALL FORWARDING
This function is similar to the basic function illustrated for the buttons.
Six buttons can be programmed for managing the same number of
calls.
–
–
–
SIGNO VIDEO DOOR PHONE
TONE SELECTION
ACCESSORIES FOR SIGNO VIDEO DOOR PHONES
SIGNO VIDEO DOOR PHONE

sec. new 2009
−−−−
9
2GO! - Technical manual
ne
W
INSTALLATION
Fasten the add-on to the bracket using the plates provided.
REAR VIEW
1,55 m
Connect the flat wire provided to the video door phone bracket.
Fasten the monitor to the bracket after connecting: extract fastening
hook αto fasten the monitor; fasten it to the bracket and block it by
pushing the hook αinwards.
α
•
•
•
Remove the clear plastic cover to access the name tags•
SIGNO VIDEO DOOR PHONE
SIGNO VIDEO DOOR PHONE
ACCESSORIES FOR SIGNO VIDEO DOOR PHONES

10
−−−−
sec. new 2009 2GO! - Technical manual
ne
W
ARCO BLACK/WHITE VIDEO DOOR PHONE
Ref. 1715/1
Besides its modern style, Arco is equipped with the best technology
for image displaying, offering the best quality/price ratio. This video
door phone can be used in any new architectural context and also to
replace the previous models Artico and Sentry+. Arco can be surface
mounted, avoiding masonry works for the flush mounting box and is
provided with a 4” flat screen that reduces the wall level stick-out.
The video door phone Ref. 1715/17 is set up to a speaker
capable interfacing with hearing aids by means of the “T”
function.
SPECIFICATIONS
The main characteristics of the video door phone are:
Flat 4” black and white video module.
Call tone volume adjustment and call exclusion function (Mute). The
Mute function is signalled by a red indicator on the front side.
MAX. MIN.MAX. MIN. MUTE
When volume is set to “MUTE” the video door phone will not ring
but the video module will light up.
Door opener button dedicated.
Additional buttons ( , ) for programming, auto power-on,
special decoder activation for secondary electrical locks, staircase
lights, etc.).
Adjustable brightness and contrast.
•
•
§
•
•
•
206 mm70 mm
230 mm
1
2
4
6
5
3
1Call volume control and adjustment
2Door opener button
3Auxiliary button: used for special functions
4Auxiliary button: used for special functions
5Brightness adjustment control
6Contrast adjustment control
TECHNICAL SPECIFICATIONS
Power voltage: 16 ÷ 18Vcc
Working: max 0,6A
Working power: Uptake: max 10W
CCIR version Vertical frequency: 50Hz ± 2Hz
Horizontal frequency: 15625 ± 300Hz
Video signal: 1Vpp 75nominal
1Vpp -6dB minimum
Kinescope: 4” flat 20mm neck
Phosphorous: P45
Geometric distorsion: vert. 5% max
horiz. 5% max
barrel 10% max
Brightness: >100cd/m2max. setting
X-rays: none
Switch-on delay: 7 sec. max
Transmitting capsule: electret microphone
Receiving capsule: 45speaker
Button voltage: 24Veff. max
Button current: 1,2Aeff
Operating temperature range: -5° ÷ +50°C
Max. humidity: 90% UR
ARCO BLACK/WHITE VIDEO DOOR PHONE Ref. 1715/1
SPECIFICATIONS
TECHNICAL SPECIFICATIONS
ARCO BLACK/WHITE VIDEO DOOR PHONE Ref. 1715/1