urmet domus MATIBUS 1752/20D User manual

DIGITAL
CALL SYSTEM
VIDEO POWER SUPPLY
ref no. 1752/20D
27.08.2015r.

POWER SUPPLY REF. NO. 1752/20D
GENERAL INFORMATIONS / USER MANUAL
VIDEO POWER SUPPLY REF. NO 1752/20D
GENERAL INFORMATIONS
Video Power Supply Ref. no. 1752 / 20D is
designed for installations of MATIBUS SE system
with the video.
The main features include:
• Ensuring energy efficiency for video installations,
• Commutation main bus data connections
and the secondary bus data for rise I and II.
• The ability to integrate video amplifier regulated
to the risers.
• The ability to quickly connect up to 3 panels
keyboard input, additional or principal.
In addition, the power supply has a green LED
indicating connection status to the mains.
CONSTRUCTION
DESCRIPTION OF TERMINAL BOARD
~0V Input voltage ~0V
~230V Input voltage ~230V
R2 Camera power positive output 18,3 VDC
R1 Camera power ground
LU1 RJ12 connector for riser LU1
LU2 RJ12 connector for riser LU2
P1 RJ45 connector – input panel no.1
P2 RJ45 connector – input panel no.2
P3 RJ45 connector – input panel no.3
MAG GL
RJ45 connector – input of main bus data
IN
MAG GL
RJ45 connector – output of main bus
OUT data
WE RJ45 connector – input of secondary
DOD bus data from power supply
ref. no. 1052/31R…33R
WE RJ45 connector – input of main bus
GL data from power supply
ref. no. 1052/31R…33R
USER MANUAL
JUMPERS P1, P2, P3, TER i AMP
In the power supply 1752 / 20D panels can be easily change
from the main bus data to secondary bus data and vice
versa.
To do this, attach a suitable jumper P1, P2 and P3,
respectively, for the panel 1, 2 and 3.Then the data line,
audio and video signal will be automatically redirected to
the correct bus data.
• No jumper means panel working on the secondary bus
data,
• Established jumper means panel working on the main bus
data
The jumper marked TER is permanently turn on termination
video signal in the main bus data.
The jumper labeled as AMP permanently turn on video
amplifier to both divisions.
VIDEO AMPLIFIER
The amplifier can increase the range of video transmission
in the risers 1 and 2. At longer distances, switching
amplifier improves the quality of the video signal.
Switching amplifier is performed by setting jumper AMP .
TECHNICAL DATA
Supply: 230 VAC
Power: 60VA
Output voltage of R2, R1: 18,3V / 2,5A
DC
Working temperature: -5
°
C
÷
+45
°
C
Power security: thermal
Dimensions:
Length 180 mm
Width 90 mm
Thickness 75 mm
Weight: 0,45kg
The length matches to 10 DIN modules.

POWER SUPPLY REF. NO. 1752/20D
ASSEMBLY AND CONNECTIONS
INSTRUCTIONS FOR CONNECTIONS
RJ45 connectors on the both sides of wires should be
installed on T-568 standard. The list of wires colors and
their corresponding pin standard T-568 shown in the figure
below:
No. Color
1 Orange-white
2 Orange
3 Green-white
4 Blue
5 Blue-white
6 Green
7 Brown-white
8 Brown
For connecting the risers with Dys-Dek 1052/54RM use
RJ12 connectors plug (6P6C). The list of wires colors and
their corresponding pins shown in the table below:
No. Color
1 Green-white
2 Orange-white
3 Blue
4 Blue-white
5 Orange
6 Green
A pair of brown color-coded wires should be connected to
terminals:
R1 – Brown-white
R2 – Brown.
The list of connectors, wires colors and their
corresponding pins shown in the table below:
Connectors LU1 i LU2 (RJ12).
No. Color Designation Description
1 Green-white 0L Ground line of
doorphones
2 Orange-white VB
Video signal.
Line B twisted
pair
3 Blue R2
Positive (+)
video power
supply (+18V
DC)
4 Blue-white R1 Ground video
power supply
5 Orange VA
Video signal.
Line A twisted
pair
6 Green LU Line of
doorphones
On the second end of this wire should be installed
plug RJ45 using T-568 standard. Plug with RJ45
connect to Dys-Dek ref. No. 1052/54RM.
Connectors WE DOD (RJ45).
No. Color Designation Description
1 Orange-white 0L
Ground line of
doorphones
LU1
2 Orange LU1
Line of
doorphones
LU1
3 Green-white 0L Ground line of
sound
4 Blue DD+
Data line of
secondary bus
data DG+
5 Blue-white DD-
Data line of
secondary bus
data DG-
6 Green LD
Line of sound
for secondary
bus data
7 Brown-white 0L
Ground line of
doorphones
LU2
8 Brown LU2
Line of
doorphones
LU2
The second end of this wire should be connected to
power supply ref. No. 1052/31R…33R.

POWER SUPPLY REF. NO. 1752/20D
ASSEMBLY AND CONNECTIONS
Connectors WE GL (RJ45).
No. Color Designation Description
1 Orange-white - Not connected
2 Orange - Not connected
3 Green-white 0L Ground line of
doorphones
4 Blue DG+
Data line of
main bus data
DG+
5 Blue-white DG-
Data line of
main bus data
DG-
6 Green LG
Line of sound
for main bus
data
7 Brown-white EO
Switching the
video signal
from the main
bus data to the
riser
8 Brown - Not connected
The second end of this wire should be connected to
power supply ref. No. 1052/31R…33R.
Connectors MAG GL (RJ45).
No. Color Designation Description
1 Orange-white VB
Video signal.
Line B twisted
pair
2 Orange VA
Video signal.
Line A twisted
pair
3 Green-white 0L Ground line of
sound
4 Blue DG+
Data line of
main bus data
DG+
5 Blue-white DG-
Data line of
main bus data
DG-
6 Green LG
Line of sound
for main bus
data
7 Brown-white R1 Ground video
power supply
8 Brown R1 Ground video
power supply
The second end of this wire should be connected to next
power supply ref. No. 1752/20D.
Connectors P1, P2 i P3 (RJ45).
No. Color Designation Description
1 Orange-white VB
Video signal.
Line B twisted
pair
2 Orange VA
Video signal.
Line A twisted
pair
3 Green-white 0L Ground line of
sound
4 Blue DG+ Data line of
bus data DG+
5 Blue-white DG- Data line of
bus data DG-
6 Green LG Line of sound
7 Brown-white R1/GND Ground video
power supply
8 Brown R Switching
camera
The second end of this wire should be connected to
panel with camera module for ex. 1752/141D.
WAY TRANSMISION OF SIGNAL
VIDEO IN THE SYSTEM
In the complex video installations, it is
recommended that the video signal from the panels
pinned in the main bus leading distribute from the
space located in the middle of the system, so that
the video signal has unidirectional character. This
method is illustrated on Fig. 4a.
Suppose that the total length of the bus data video
denoted as S, then:
S = A1 + A2 + … + An + B1 + B2 + … + Bn + C1
lub;
S = A1 + A2 + … + An + B1 + B2 + … + Bn + C2
lub;
S = A1 + A2 + … + An + B1 + B2 + … + Bn +
Cn.
In the case where the video bus data length S
exceeds 250m use the video distributor Ref.
955/40. How to connect the distributor Ref. 955/40
is shown in Fig. 4b.
MONTAGE
The power supply is mounted on a DIN rail
or screwed to the substrate using two screws or
bolts minimum dimensions Ø4 / 50mm Fig. 3. The
method of mounting the power supply is shown in
Figure 1a and 1b. To mount the power supply for
DIN rail use a flat screwdriver to pull the pin
locking, then put the power supply on a DIN rail,
then release the pin. After mounting the power
supply on the rail, you can protect it against
dismantling by fusing the pin with the casing using
bolt and nut dimensions Ø4 / 36mm. The
protection method shown in Figure 2.

POWER SUPPLY REF. NO. 1752/20D
ASSEMBLY AND CONNECTIONS
Fig. 1a The method of mounting the power supply
on rail (pull the pin).
Rys. 1b The method of mounting the power supply
on rail (release the pin).
Rys. 2 Protect against dismantling by fusing the pin
with the casing
Rys.3 Screwing to the substrate using two screws or
bolts
ELECTRICAL CONNECTIONS
Electrical connections should be performed
by a person with knowledge of the basic issues of
electrical engineering. All connections should be
made in accordance with the attached schedule,
and with disconnected power supply.
The building installation should include, multi-
pole connector adapter with at least 3 mm spacing
between all poles. The supply voltage must be
accompanied only after all connections and the
protective cover after screwing supply terminals.

POWER SUPPLY REF. NO. 1752/20D
DOORPHONE SYSTEM IN MASTER / SLAVE CONNECTION
WITH POWER SUPPLY 1752/20D
~230
0L
OC1
OC2
AC1
AC2
EO
~0
EI
0L
+20
DD+
LU2
LU1
0L
LD
0L
~230
~0
~0
~12
+20
0L
AC1
AC2
LG
D (D+)
GND
ELEKTROZACZEP
+CL
-CL
NO
C
NC
GND
EXI
PH
R
0L
+V
DODATKOWE STEROWANIE
NP. BRAMY AUTOMATYCZNEJ
VA
VB
GND
R
R2
4
*
7
1
5 6
0
8
#
9
2 3
Błędy kasuj przyciskiem......
Aby otworzyć drzwi
wciśnij.................... .............
oraz
wprowadź kod otwarcia
i zatwierdź przyciskiem........
#
#
*
Wybierz numer lokalu
i poczekaj na połączenie
lub zatwierdź przyciskiem... #
D-
DD-
P1 P2 P3
WE
DOD
WE
GŁ
MAG
GŁ MAG
GŁ
LU1 LU2
~0 ~230
0L
DG+
LG
DG-
KAMERA
LG
SKR
AGND
AVDD
SPK
red
black
AC1
AC2
LG
D (D+)
GND
ELEKTROZACZEP
+CL
-CL
NO
C
NC
GND
EXI
PH
R
0L
+V
DODATKOWE STEROWANIE
NP. BRAMY AUTOMATYCZNEJ
VA
VB
GND
R
R2
4
*
7
1
5 6
0
8
#
9
2 3
Błędy kasuj przycis kiem......
Aby otworzyć drzwi
wciśnij........... ......................
oraz
wprowadź kod otwarcia
i zatwierdź przyciski em........
#
#
*
Wybierz numer lokalu
i poczekaj na połączenie
lub zatwierdź przyc iskiem... #
D-
KAMERA
LG
SKR
AGND
AVDD
SPK
red
black
UTP KAT 6
UTP KAT 5E
UTP KAT 5E RISER IN
RISER OUT
UTP KAT 5E UTP KAT 5E
OUT DOUT C
IN
OUT
IN
OUT 3DD
R2
R1
GND
3DC
GND
3DA
GND
3DB
GND
PRZYCISK DZWONKA LOKALNEGO
PRZYCISK DZWONKA LOKALNEGO
PRZYCISK DZWONKA LOKALNEGO
PRZYCISK DZWONKA LOKALNEGO
UTP KAT 5E
UTP KAT 5E RISER IN IN
RISER OUT
UTP KAT 5E UTP KAT 5E
OUT DOUT C
IN
OUT
IN
OUT 3DD
R2
R1
GND
3DC
GND
GNDGND
PRZYCISK DZWONKA LOKALNEGO
PRZYCISK DZWONKA LOKALNEGO
PRZYCISK DZWONKA LOKALNEGO
PRZYCISK DZWONKA LOKALNEGO
OUT AOUT B
3DA3DB
OUT AOUT B
4k7
1
9
6
2
CA
Y1
X2
X1
Y2
NIEBIESKI
BRĄZOWO-BIAŁY
BRĄZOWY
NIEBIESKO-BIAŁY
4k7
1
9
6
2
CA
Y1
X2
X1
Y2
NIEBIESKI
BRĄZOWO-BIAŁY
BRĄZOWY
NIEBIESKO-BIAŁY
UTP KAT 6 UTP KAT 6
R1
V3
RD
UTP (4x2x0.5 kat.5e)
UTP (4x2x0.5 kat.5e)
UTP kat.6
UTP kat.6
do następnych Dysdeków
do następnego
zasilacza
1752/20D
do następnego
zasilacza
1752/20D
IN
UTP (4x2x0.5 kat.5e
lub UTP 6)
UTP (4x2x0.5 kat.5e
lub UTP 6)
UTP (4x2x0.5 kat.5e
lub UTP 6)
(RJ45)
UTP (4x2x0.5 kat.5e
lub UTP 6)
(RJ45) (RJ45)
(RJ45)
(RJ45)
(RJ45) (RJ12) (RJ12) (RJ45)
R1 R2
(RJ45)
(RJ45)
P3 P2 P1
OFF OFF ON
do następnego
panela
1752/141D
(RJ45)
R1
R2

ZASILACZ NR REF. 1752/20D
WAY TRANSMISION OF SIGNAL VIDEO IN THE SYSTEM
4
*
7
1
5 6
0
8
#
9
2 3
Błędy kasuj przyciskiem......
Aby otworzyć drzwi
wciśnij.................................
oraz
wprowadź kod otwarcia
i zatwierdź przyciskiem........
#
#
*
Wybierz numer lokalu
i poczekaj na połączenie
lub zatwierdź przyciskiem... #
4
*
7
1
5 6
0
8
#
9
2 3
Błędy kasuj przyciskiem......
Aby otworzyć drzwi
wciśnij.................................
oraz
wprowadź kod otwarcia
i zatwierdź przyciskiem........
#
#
*
Wybierz numer lokalu
i poczekaj na połączenie
lub zatwierdź przyciskiem... #
4
*
7
1
5 6
0
8
#
9
2 3
Błędy kasuj przyciskiem......
Aby otworzyć drzwi
wciśnij.................................
oraz
wprowadź kod otwarcia
i zatwierdź przyciskiem........
#
#
*
Wybierz numer lokalu
i poczekaj na połączenie
lub zatwierdź przyciskiem... #
4
*
7
1
5 6
0
8
#
9
2 3
Błędy kasuj przyciskiem......
Aby otworzyć drzwi
wciśnij.................................
oraz
wprowadź kod otwarcia
i zatwierdź przyciskiem........
#
#
*
Wybierz numer lokalu
i poczekaj na połączenie
lub zatwierdź przyciskiem... #
4
*
7
1
5 6
0
8
#
9
2 3
Błędy kasuj przyciskiem......
Aby otworzyć drzwi
wciśnij.................................
oraz
wprowadź kod otwarcia
i zatwierdź przyciskiem........
#
#
*
Wybierz numer lokalu
i poczekaj na połączenie
lub zatwierdź przyciskiem... #
4
*
7
1
5 6
0
8
#
9
2 3
Błędy kasuj przyciskiem......
Aby otworzyć drzwi
wciśnij.................................
oraz
wprowadź kod otwarcia
i zatwierdź przyciskiem........
#
#
*
Wybierz numer lokalu
i poczekaj na połączenie
lub zatwierdź przyciskiem... #
4
*
7
1
5 6
0
8
#
9
2 3
Błędy kasuj przyciskiem......
Aby otworzyć drzwi
wciśnij.................................
oraz
wprowadź kod otwarcia
i zatwierdź przyciskiem........
#
#
*
Wybierz numer lokalu
i poczekaj na połączenie
lub zatwierdź przyciskiem... #
4
*
7
1
5 6
0
8
#
9
2 3
Błędy kasuj przyciskiem......
Aby otworzyć drzwi
wciśnij.................................
oraz
wprowadź kod otwarcia
i zatwierdź przyciskiem........
#
#
*
Wybierz numer lokalu
i poczekaj na połączenie
lub zatwierdź przyciskiem... #
4
*
7
1
5 6
0
8
#
9
2 3
Błędy kasuj przyciskiem......
Aby otworzyć drzwi
wciśnij.................................
oraz
wprowadź kod otwarcia
i zatwierdź przyciskiem........
#
#
*
Wybierz numer lokalu
i poczekaj na połączenie
lub zatwierdź przyciskiem... #
Fig.4a
4
*
7
1
5 6
0
8
#
9
2 3
*4
*
7
1
5 6
0
8
#
9
2 3
*
4
*
7
1
5 6
0
8
#
9
2 3
*
4
*
7
1
5 6
0
8
#
9
2 3
*
4
*
7
1
5 6
0
8
#
9
2 3
*
4
*
7
1
5 6
0
8
#
9
2 3
*
4
*
7
1
5 6
0
8
#
9
2 3
*4
*
7
1
5 6
0
8
#
9
2 3
*4
*
7
1
5 6
0
8
#
9
2 3
*
R1 R2 A B
IN
B
A
OUT
I
B
A
OUT
II
R1 R2
MAG GL
OUT
DO NASTĘPNEGO
ZASILACZA 1752/20D
DO NASTĘPNEGO
ZASILACZA 1752/20D
B
A
OUT
III
B
A
OUT
IV
R1 R1
TER
2 x
82?
2 x
82?
ON
Fig. 4b

MIWI-URMET sp. z o. o.
ul. Pojezierska 90A
91-341 Łódź
tel: [phone]
fax: [phone]
e-mail: [e-mail]
http:/www.miwiurmet.pl