OPERATION INSTRUCTION
10
DESCRIPTION OF TERMINAL BOARDS
LG Voice line
0L GND.
DData line.
RAdditional control terminal for video version
GND Contacts input/output ground.
+V Input voltage + 15…+20 V DC.
AC1 Input voltage ~12 V AC.
AC2 Input voltage ~12 V AC.
+CL Electric lock output (+).
-CL Electric lock output (-).
NC Relay normally closed contact.
CRelay Common contact.
NO Relay normally open contact.
PH Door lock release.
GND Contacts input/output ground.
EXI Door sensor input.
X1 Microphone socket.
X2 Speaker socket.
X12 Backlight module power socket (only in 1052/11../11D or
1052/16../16D).
X10 Dallas key socket.
BASIC SYSTEM FUNCTIONS
1. Calling to all house phones,
2. General and individual opening codes,
3. Dallas key reader (only in 1052/15../15D and 1052/16../16D),
4. Exit transmitter NC-O-NO controlled by general and individual
opening codes and additional button in the house phone,
5. Open door input.
6. Exit dedicated to handling video,
7. Hall button timed input,
8. Programmable system,
9. System information shown on LED display.
SERIAL NUMBER OF CALL MODULE
To see serial number of call module:
-first push this buttons combination 0
∗
2
#,
then you will see less
significant part of serial number.
- press
#
to show the rest part of serial number.
SERIAL NUMBER OF POWER SUPPLY
To see serial number of power supply:
- first push this button combination: 0
∗
1
#
then you will see the less
significant part of serial number of this power supply.
- press
#
to show the rest part of serial number.
RESET OF POWER SUPPLY
To reset power supply please push this button combination
0
∗
666
#
.
To reset MASTER power supply, push this button
combination in call module connected to the main channel.
EMERGENCY ENTER TO THE PROGRAMMING MODE
If the entering password is unknown, we are able to enter to the
programming mode by pressing two buttons- first SW1 button which
is located on PCB board inside the panel and after this function we
have got maximum 2 seconds time to press
∗
∗∗
∗
button on the
keyboard.
OPERATION INSTRUCTION
DEFAULT SETTINGS OF USER CODES
Power supply is default programmed for the first 50 user codes in
the first riser. Default, first riser handle user codes in range 1-50,
but system is able to generate 255 user codes automatically.
Number of user codes can be increase by changing parameters in
programming mode. In order to increase number of user codes
automatically, change parameters in steps 7.4 and 7.5, and
generate new individual opening user codes by step 4.4 .
SIGNALING OF DOOR LOCK AND NO-NC RELEASING
If the door lock or NO-C-NC relay is releasing, call module emits
beeps and on display appears rotating dashes.
CALL TO USERS
Each user of the Matibus SE system can be called by entering the
appropriate number. The personal user code can compose of
numbers from 1 to 4 long and in range from 1……9999. These
users’ codes (logic codes) are associated with the house phones
codes (physical codes). Every house phone has unique code
depending of the number of riser and of
the
setting the jumpers in
house phone. In Matibus SE system is possible that two house
phones can work in parallel.
After entering the correct user code we can wait 3 s and the call
connection will be initiated automatically, or press the
#
button and
connect straight away.
If we made a mistake please press
∗
∗∗
∗
and this will delete previous
number.
•Called house phone will ring as long as it was programmed.
The programmable time is from 1s to 30 s. The answering time
is also programmable in the same range what ringing time from
1 s to 30 s. Pickup time signaled is a recurrent dual signal calls
(option is on)
•Conversation is possible when we picked up the handest.
During the conversation we can open the door by pressing
dedicated button for this function. After pressed the button in
the receiver will be played short signal to confirm this function.
The electric lock will be open as long as we programmed it, the
range of this time is from 1s to 30s.
Maximum time of conversation is from 30s to 120s, after that time in
the receiver will be played signal to warn that the conversation is
nearly over, and after it, the conversation will be disconnected.
GENERAL OPENING CODES IN USE
We are able to open door using 1 from 64 general 4 digits opening
codes. To do it:
•
Press
#
button,
•
Enter 1 of 64 general 4 digital opening code, for example:
1234,
•
Confirm by pressing
#
button.
General opening code can be turned off in a programming mode.
INDIVIDUAL OPENING CODES IN USE
We are able to open door using 1 of the individual opening code.
This code is 4 digits. To open door with this code first we have to
enter logical user code and than individual opening code which was
associated with each other. Individual opening code can be from 5
to 8 digits.
•
Press
#
button,
•
Enter individual opening code – from 5 to 8 digits (logical user
code + 4 digits combination code),
•Confirm by pressing
#
button.
