urmet domus 6025/401 User manual

INSTRUKCJA
DOORPHONE ANALOG SET
WITH PANEL ELITE (flush mounting)
AND UNIPHONE SIGNO
6025/401
6025/402
6025/441
6025/442
Version I, 10.09.2018

DOORPHONE ANALOG SET
6025/401 6025/402 6025/441 6025/442
2
SPEAKER’S MODULE REF. NO. 6025/PR1
6025/PR2
GENERAL INFORMATIONS
Speaker's plate is made of stainless steel, vandal-proof degree of
protection IK07. Its compact size makes it ideal for mounting on
narrow pillars fence. Additional protection is a patent bolt securing
the front panel. Speaker’s module have 1, 2 call buttons and the
control module.
Speaker’s module can be mounted in two versions:
• surface-mounted –have to applied housing
Ref. no. 6025 / OND-M.
• flush have to applied frame Ref. no. 6025 / RP-OP-M. This is a
version without the visor. Very well masks any unevenness hole
prepared for the panel.
Speaker’s modules ref. no. 6025 / PR1, 6025 / PR2co-
operate with the following types of power supplies:
- Version classical: 18A2, 18L1;
- Version witch intercom: 19A2, 19L1.

CONNECTORS DESCRIPTION
441 "plus" microphone amplifier,
MK "minus" microphone amplifier,
GL, GL loudspeaker panel
AC, AC power panel
G GND key generator call signal,
G1 terminal of the first call button uniphone
G2 terminal of the second call button uniphone
TECHNICAL DATA
Power supply:
12V AC
Working temperature:
-20C +45C
Dimensions with
nr. ref 6025/OND-M
157 x 67 x 23 [mm] (without visor)
157 x 67 x 35 [mm] (with visor)
Dimensions with
nr. ref 6025/ RP-OP-M
176 x 87 x 23 [mm]
Level of security
IK 07
Weight:
0,18 kg
Dimensions of info window: 30 mm x 70 mm
DIMENSIONS OF CASING
Surface-mounted housing ref. no. 6025/OND-M
Flush-mounted housing ref. no. 6025/RP-OP-M

SPEAKER’S MODULE REF. NO. 6025/PR1..2
MONTAGE
3
PANEL MONTAGE
INSERTING THE LABEL TO INFO WINDOW
To attach the label information have to:
1. Unscrew with the included wrench the screw that secures
the front panel.
2. Remove the lower screw fastening motherboard.
PHOTO NO. 1
3. Remove the label
PHOTO NO. 2
4. In the slot in the faceplate Plexiglas insert the correct
label.
5. Tighten the screw that secures the motherboard.
In the original packaging is one additional label.
You can download from the website
http://urmet.com.pl/INSTRUKCJE/6025_PRx_FOR
MATKA.pdf template labels printable version.
FLUSH MOUNTING

SPEAKER’S MODULE REF. NO. 6025/PR1..2
MONTAGE
4
To mount the panel-mounted version follow the steps below.
1. Loosen the screw with a key patent secures the front panel.
Remove the face plate.
2. Insert the wires connecting using one B of the holes in the back
of housing (Photo below).
3. Place housing in the wall (hole).
4. Screw housing to the ground using the holes A.
5. Connect the wires to the appropriate terminals speaker’s module
according to the wiring diagram.
6. Close and screw on the front panel of the module.

UNIPHONE NR REF. 1140/1 , 1140/41
GENERAL INFOMATIONS
5
UNPHONE “SIGNO” NR REF. 1140/1 (white),
1140/41 (black)
Rys. 1 Dimensions
The uniphone is designed to work in 4 + n analogue doorphone
systems. Uniphone with reference number: 1140/1 is available in
white. It is equipped with a door open button, one additional button
and the option to buy two more function buttons.
1140/41 is in black. It is equipped with a door open button and three
additional function buttons.
The function buttons are independent of each other and can be
used for various additional functions, e.g.
• calling another uniphone (intercom - no such function in the
set),
• lighting in the staircase,
• opening the second electrolock or gate.
Signo Unifon has the option of adding a volume call control ref.
1140/53 (not included)
Rys. 2 Volume call control
CONNECTORS DESCRIPTION
Inside the uniphone, after removing its housing on the PCB, there is
a terminal strip used to connect the camera to the system. The
function buttons have independent contacts.
Description of terminals:
T1, T2. T3 terminals for function keys
G / T terminals for function keys
CA call,
1 speaker line,
2 microphone line,
6, 10 mass,
9 electric lock line

UNIPHONE NR REF. 1140/1 , 1140/41
MONTAGE
6
INSTALATION
SIGNO can be mounted on a wall
WALL MOUNT
It is advisable to install the uniphone at such a height that the
highest part of the device is at a height of 1.55 m from the ground
To mount a uniphone in a hanging version, follow the steps below.
1.Remove the uniphone housing by releasing plastic latches using
a screwdriver blade (Fig. 4).
Rys. 3 way of opening the uniphone housing
2. Attach the uniphone to the wall using two dowels supplied with
the uniphone (Fig. 5).
3. Route the wires through the hole in the back of the uniphone.
4. Cut the wires to the required length and isolate their ends.
Rys. 4 montage of the SIGNO uniphone
122/5000
5.Connect the cable ends to the appropriate terminals of the
uniphone connector.
6. Reconnect both housing parts (Fig. 6).
Rys. 5 Fig. 6 way of closing the housing

POWER SUPPLY NR REF. 18A2
GENERAL INFORMATIONS
7
POWER SUPPLY UNIT REF. 18A2
BASIC FEATURES
Power supply unit ref. 18A2 it is a part of house
phone system. Apart from power supply unit, each
house phone system must consist of:
entrance panel with suitable loudspeaking unit and
push buttons.
Power supply unit ref. 18A2it is a product from the latest
generation of power supply units produced by MIWI-
URMET. It is equipped with overload protection and special
circuit which is responsible for quiet call signal heard in
entrance panel during the call (call feedback). The additional
triac is used to release electric lock.
TERMINALS DESCRIPTION
~12 voltage 12Vac used to backlight or to release
electric lock,
~0 ground for voltage12Vac;
0ground;
MU microphone output for house phones;
SU loudspeaker output for house phones;
GP loudspeaker output for entrance panel;
MP microphone output for entrance panel;
G tone generator;
LZ door lock release line for house phones;
Z electric lock;
SETTINGS
The power supply ref. 18A2 is equipped with 2
potentiometers for adjusting external (on the right) and
internal volume (on the left).
Exchanging of the fuse is possible after taking the
cover of power supply off. Remember to switch off the
mains before performing this operation.
BLOCK DIAGRAM
n = number of house phones
TECHNICAL SPECIFICATIONS
Power supply
230 V a. c. 50/60 Hz
Power
10 VA
Working temperature
-5°C ÷+45°C
Min. Resistance for
tone generator
> 20 Ohm
Protection
fuse T100mA
Dimensions (L x W x
D)
106 x 90 x 66 mm (6 DIN)
–without external cover
110 x 130 x 66 mm
–with external cover

SCHEMA
WITH POWER SUPPLY 18A2 AND SPEAKER’S MODULE 6025/PR1
8

SCHEMA
WITH POWER SUPPLY 18A2 AND SPEAKER’S MODULE 6025/PR2
9

MIWI-URMET Co. Ltd.
Pojezierska 90A
90-341 Lodz, Poland
tel: [phone]
fax: [phone]
e-mail: [e-mail]
http:/www.miwiurmet.pl
The symbol of the crossed out wheeled bin indicates that the product (electrical and electronic equipment) should not be placed in municipal
waste. Please check local regulations for disposal of electronic products.