UWE ADM Series User manual

CONTENTS
CAUTIONS
1. INSTALLATION
2. SPECIFICATIONS
3. KEYBOARD LAYOUT AND DESCRIPTION
4. INITIAL SETUP
5. INSTRUCTION FOR USE
6. TROUBLE SHOOTING
7. DAILY CARE AND MAINTENANCE

CAUTIONS
1. This unit is legal for trade only when it is sealed
(and/or stamped) and bearing a serial number. Do not
attempt to break the seal (or stamp) affixed to this
scale or remove the serial number. Contact your dealer
for more information and after sales service.
2. For most accurate weighing result, do not use this
scale in where or when the environment condition falls
beyond as those listed on SPECIFICATIONS.
3. Do not attempt to open this unit or conduct any trouble
shootings other than those listed on TROUBLE
SHOOTING.
4. Do not submerge scale into water.
5. Do not use pressurized water nozzle for cleaning.
6. Do not use this scale for chemical substances or in
any environment that contains chemical vapor.
7. Precision measuring instrument, handle with care.
8. Always apply the rubber cap (FIG 2 E) when not in
charging.
9. Do not attempt to open scale.

1. INSTALLATION
1.1 Check and make sure that the following accessories
are included:
This operation manual
Scale x 1
Plastic platter x 1
Stainless steel cover x 1
Screw x 1
Rubber cap x 1
Power adaptor x 1
Contact your dealer if any items are missed.
1.2 Lock the plastic platter (FIG 1 A) to the platter
holder, with the screw (FIG 1 B) included and then
apply the rubber cap (FIG 1 C).
1.3 Place the stainless steel platter (FIG 1 D) onto
the plastic platter.
1.4 Power on the scale
a. Before plugging the power adaptor into
electricity outlet, check and make sure that the
input voltage of power adaptor matches with the
output voltage of the outlet. If not, do not plug
in and contact your dealer immediately.
b. Before first time use, plug the adaptor into the
wall outlet and charge the scale for at least 8
hours.
c. After battery is fully recharged, remove adaptor
from scale. Apply the rubber cap (FIG 2 E) to seal
the DC input jack of scale.

FIG 1
FIG 2

2. SPECIFICATIONS
Model No.
Capacity
(Max)
Division (e)
OIML
Non-OIML
ADM-1500
1500g
0.5g
NIL
ADM-3000
3000g
1g
0.5g
ADM-6000
6000g
2g
1g
ADM-15K
15kg
0.005kg
0.002kg
ADM-30K
30kg
0.01kg
0.005kg
Tare Range
Full tare range (Subtractive)
Display
5 x 24mm LCD display
Operation
Environment
0o~40oC (32o~104oF),
Non-condensed. R.H.≦85%
Power source
By Built-in rechargeable battery or power
adaptor
Specifications subject to change without notice
*The minimum load of 15kg for Non-OIML application is
25e
NOTE 1:
OIML = Legal for trade (1/3000)
Non-OIML = Not legal for trade (1/6000~1/7500)
NOTE 2:
Display resolution of avoirdupois weight units (lb/lb
and lb/oz) always = 1/3000

3. KEYBOARD LAYOUT AND DESCRIPTION
1. ON/ZERO KEY
Press this key to turn scale on, or reset displayed
weight to zero when the scale is not loaded.
2. TARE KEY
Press this key to tare off the weight of a container
during normal operation.
3. MODE KEY
Press this key to shift among different weight units
and display parameters.
4. OFF KEY
Press this key to turn scale off.

5. ZERO INDICATOR
This indicator appears to indicate a zero weight
status.
6. NET INDICATOR
This indicator appears to indicate the tare function
is in effect and weight displayed is net weight.
7. METRIC UNIT INDICATOR
This indicator appears to indicate the weighing unit
being selected is at metric (kilogram or gram).
8. LO-BAT INDICATOR
When this indicator appears, recharge the scale
immediately. Failure to do so may cause unrecoverable
damage to the rechargeable battery inside scale.
9. IN-CHARGE INDICATOR
Red color: Recharging battery
Green color: Charging completed
10. lb/lb UNIT INDICATOR
This indicator appears to indicate the weighing unit
being selected. Two avoirdupois weight units are
available and this indicator means the weighing unit
is at decimal pound (e.g. 5.62 means 5.62 lb).
11. lb/oz UNIT INDICATOR
This indicator appears to indicate the weighing unit
being selected is at pound/ounce (e.g. 2.15.1 means
2 lb and 15.1 ounce).

4. INITIAL SETUP
4.1 PLACING THE SCALE
In order to obtain an accurate weighing result, the scale
must be placed on a strong and level surface. If required,
adjust the adjustable feet (FIG 2 F) underneath scale
to obtain a level position. Refer to the bubble indicator
for leveling condition.
4.2 INTERNAL SETTING
4.2.1 Display Segment Check
User can enter this function to check to see if the display
and backlight (if purchased) are functioning properly.
a. Scale is off
b. Press and hold TARE, then press ON/ZERO
c. Scale displays F.1
d. Press TARE once
e. Scale displays F.2
f. Press MODE and all segments will light up to allow
user to check the condition of display
g. Press TARE for next function setup or ON/ZERO to
restart the scale
4.2.2 Select Auto Power Off Setting
The scale is equipped with Auto Power Off Function. The
scale will power off automatically if it is not used
for 4 minutes. Follow the below steps to enable/disable
Auto Power Off Function.

a. Scale is off
b. Press and hold TARE, then press ON/ZERO
c. Scale displays F.1
d. Press TARE three times
e. Scale displays F.4
f. Press MODE to shift between 0._OFF and 4._OFF
-To enable Auto Power Off Function, press TARE when
4._OFF appears
-To disable Auto Power Off Function, press TARE when
0._OFF appears
g. Press ON/ZERO to restart the scale or TARE for next
function setup
4.2.3 Select RS-232 Baud Rate & Protocol
This scale is equipped with 4 RS232C output baud rate
and 2 transmission protocol settings for user to select.
a. Scale is off
b. Press and hold TARE, then press ON/ZERO
c. Scale displays F.1
d. Press TARE four times
e. Scale displays F.5
f. Press MODE to select baud rate of 4800, 9600, 19200,
38400
g. Press and hold MODE for 2 seconds to enter
transmission protocol setup
h. Press MODE to select protocol of N81 or E71
i. When the preferred transmission protocol shows on
display, press ON/ZERO to confirm and restart the
scale or TARE for next function setup